How Are Coil Springs Removed and Installed on 2004 Dodge Ram 1500?

First, raise and support the vehicle, then take out the front wheel and tire. Put support under the lower control arm on the outer side so the car doesn't sag and remove the shock absorber. Attach the Spring Compressor into the lower suspension arm, through the coil spring and into the shock hole on the frame, with the bell-shaped end of the adapter touching the lower suspension arm and fasten the nut at the shock hole finger tight before loosening it by 1/2 turn so the spring is still held in place. Then remove the lower stabilizer link and the nut on the lower ball joint at the knuckle and detach the ball joint from the knuckle with Ball Joint Remover 8677, supporting the upper arm and knuckle to stop downward rebound. Get rid of the lower arm support rod, then tighten the compressor to give room for the ball joint's removal and unbolt the control arm's pivot bolt for easier swing down. Gradually relax how tight the spring compressor is, to let the lower suspension arm lower and then unhook everything and extract both the coil spring and its isolator pad. To install the isolator pad, tape it to the coil spring at the top and set it in the lower suspension arm just right. Replace the Spring Compressor DD-1278 into the car by feeding it through the lower arm, spring and shock hole in the frame and tighten the device nut to lower the spring. Remove the upper control arm's holder and lower the ball joint into the steering knuckle, then use a 20 mm wrench to tighten the retaining nut to the required torque, followed by an additional 90° turn if it is a 1500 series or 135 Nm and another turn for the HD 4X2. Remember to uninstall the spring compressor, hold the lower control arm on the outer side and reinstall the shock absorber and the stabilizer link. Take off the lower control arm support, fit the wheel and tire assembly and put the car on the ground. Next, let the vehicle rest on the floor loaded with weight and secure both the front and rear control arm mounting bolts to 285 Nm (210 ft. lbs.) on HD 4X2 and 204 Nm (150 ft. lbs.) for LD 4X2 once the vehicle is at the shop.

OEM 2004 Dodge Ram 1500 Coil Springs

Strut Spring

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Coil Springs found

View related parts
2004 Dodge Ram 1500 Spring, Front Part Number: 52106606AA
$8.76 MSRP: $11.10
You Save: $2.34 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Front Coil; Coil Spring, Front; Coil Spring Kit Front; Coil Spring Set; Coil Springs; Spring Front Coil
- Position: Front
- Item Weight: 17.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52106606AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Ram 1500 Submodels:
- Laramie, SLT, SRT-10, ST | 10 Cyl 8.3 L GAS, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2004 Dodge Ram 1500 Spring, Front Part Number: 52106602AA
$52.99 MSRP: $67.18
You Save: $14.19 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Front Coil; Coil Spring, Front; Coil Spring Kit Front; Coil Spring Set; Coil Springs; Spring Front Coil
- Position: Front
- Item Weight: 12.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52106602AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Ram 1500 Submodels:
- Laramie, SLT, SRT-10, ST | 10 Cyl 8.3 L GAS, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2004 Dodge Ram 1500 Spring, Front Part Number: 52106605AA
$131.49 MSRP: $166.68
You Save: $35.19 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Front Coil; Coil Spring, Front; Coil Spring Set; Coil Springs; Spring Front Coil
- Position: Front
- Item Weight: 16.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52106605AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Ram 1500 Submodels:
- Laramie, SLT, SRT-10, ST | 10 Cyl 8.3 L GAS, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2004 Dodge Ram 1500 Spring, Front Part Number: 52106604AA
Product Specifications
- Other Name: Spring - Front Coil; Coil Spring, Front; Coil Spring Set; Coil Springs; Spring Front Coil
- Position: Front
- Item Weight: 15.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52106604AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Ram 1500 Submodels:
- Laramie, SLT, SRT-10, ST | 10 Cyl 8.3 L GAS, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2004 Dodge Ram 1500 Coil Spring, Front Part Number: 52106600AA
Product Specifications
- Other Name: Spring - Front Coil; Coil Spring, Front; Coil Springs; Spring; Spring Front Coil
- Position: Front
- Item Weight: 12.00 Pounds
- Item Dimensions: 18.4 x 12.6 x 8.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52106600AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Ram 1500 Submodels:
- Laramie, SLT, SRT-10, ST | 10 Cyl 8.3 L GAS, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2004 Dodge Ram 1500 Spring, Front Part Number: 52106608AA
Product Specifications
- Other Name: Spring - Front Coil; Coil Spring, Front; Coil Springs; Spring Front Coil
- Position: Front
- Item Weight: 19.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52106608AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Ram 1500 Submodels:
- Laramie, SLT, SRT-10, ST | 10 Cyl 8.3 L GAS, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2004 Dodge Ram 1500 Spring, Front Part Number: 52106607AA
Product Specifications
- Other Name: Spring - Front Coil; Coil Spring, Front; Coil Springs; Spring Front Coil
- Position: Front
- Item Weight: 19.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52106607AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Ram 1500 Submodels:
- Laramie, SLT, SRT-10, ST | 10 Cyl 8.3 L GAS, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2004 Dodge Ram 1500 Spring, Front Part Number: 52106603AA
Product Specifications
- Other Name: Spring - Front Coil; Coil Spring, Front; Coil Spring Set; Coil Springs; Spring Front Coil
- Position: Front
- Item Weight: 14.20 Pounds
- Item Dimensions: 15.7 x 5.5 x 5.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52106603AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Ram 1500 Submodels:
- Laramie, SLT, SRT-10, ST | 10 Cyl 8.3 L GAS, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2004 Dodge Ram 1500 Spring, Front Part Number: 52106601AA
Product Specifications
- Other Name: Spring - Front Coil; Coil Spring, Front; Coil Springs; Spring Front Coil
- Position: Front
- Item Weight: 12.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52106601AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Ram 1500 Submodels:
- Laramie, SLT, SRT-10, ST | 10 Cyl 8.3 L GAS, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2004 Dodge Ram 1500 Spring, Front Part Number: 5290605AB
Product Specifications
- Other Name: Spring - Front Coil; Coil Spring, Front; Coil Springs; Spring Front Coil
- Position: Front
- Replaces: 5290605AA
- Item Weight: 2.10 Pounds
- Item Dimensions: 14.4 x 5.3 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5290605AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Ram 1500 Submodels:
- Laramie, SLT, SRT-10, ST, Sport, TRX4 | 10 Cyl 8.3 L GAS, 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8.3L V10

2004 Dodge Ram 1500 Coil Springs Parts and Q&A

Q: How Are Coil Springs Removed and Installed on 2004 Dodge Ram 1500?
A: First, raise and support the vehicle, then take out the front wheel and tire. Put support under the lower control arm on the outer side so the car doesn't sag and remove the shock absorber. Attach the Spring Compressor into the lower suspension arm, through the coil spring and into the shock hole on the frame, with the bell-shaped end of the adapter touching the lower suspension arm and fasten the nut at the shock hole finger tight before loosening it by 1/2 turn so the spring is still held in place. Then remove the lower stabilizer link and the nut on the lower ball joint at the knuckle and detach the ball joint from the knuckle with Ball Joint Remover 8677, supporting the upper arm and knuckle to stop downward rebound. Get rid of the lower arm support rod, then tighten the compressor to give room for the ball joint's removal and unbolt the control arm's pivot bolt for easier swing down. Gradually relax how tight the spring compressor is, to let the lower suspension arm lower and then unhook everything and extract both the coil spring and its isolator pad. To install the isolator pad, tape it to the coil spring at the top and set it in the lower suspension arm just right. Replace the Spring Compressor DD-1278 into the car by feeding it through the lower arm, spring and shock hole in the frame and tighten the device nut to lower the spring. Remove the upper control arm's holder and lower the ball joint into the steering knuckle, then use a 20 mm wrench to tighten the retaining nut to the required torque, followed by an additional 90° turn if it is a 1500 series or 135 Nm and another turn for the HD 4X2. Remember to uninstall the spring compressor, hold the lower control arm on the outer side and reinstall the shock absorber and the stabilizer link. Take off the lower control arm support, fit the wheel and tire assembly and put the car on the ground. Next, let the vehicle rest on the floor loaded with weight and secure both the front and rear control arm mounting bolts to 285 Nm (210 ft. lbs.) on HD 4X2 and 204 Nm (150 ft. lbs.) for LD 4X2 once the vehicle is at the shop.