How to Install a TPMS Sensor on Dodge Avenger?

You should start by removing old seal 2 and metal washer 1 and replace them at the bottom of the sensor valve stem 6 before fitting the sensor. Clean all around the sensor/valve mounting area in wheel 5, so the wheel surface is spotless. Be careful not to press the sensor antenna strap, so press near metal valve stem 2 as you move the sensor into the wheel from inside. Put washer 3 and sensor nut 3 into place by hand, then push down on the sensor housing 2 to make it join with the interior of the wheel; then tighten sensor nut 3 to 8 Nm-71 in. lbs. Make sure not to crank the sensor nut too carefully, since it might result in the sensor separating from the valve. For rotating wheel tire changers, place the sensor valve stem 2 approximately 280° away from the head of the changer. For rotating tool tire changers, position it 210° to the right away from the mounting/dismounting tool and be sure the sensor is clear of the lower part of the bead breaker. Make the tire pressure fit the instructions on the Tire Pressure Label and be sure the original valve stem cap is properly fixed. Affix the tire and wheel assembly to the vehicle, get rid of the support and lower down the car. Use TPM-RKE Analyzer, 9936, to program the tire pressure sensor ID into the WCM/SKREEM or just drive above 15 mph (24 km/h) for 10 minutes after the car has been at rest for at least 20 minutes. If a sensor can't be programmed to the correct signal strength, follow the diagnostic requirements.

OEM Dodge Avenger TPMS Sensor

Tire Pressure Monitoring System Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 TPMS Sensors found

View related parts
Dodge Avenger TPMS Sensor Part Number: 68078861AC
$106.43 MSRP: $161.00
You Save: $54.57 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Tire Pressure; Tire Pressure Monitoring System Sensor; TPMS Sensor Service Kit; Tire Pressure Sensor; Pressure Sensor; Hardware Kit; Sensor
- Replaces: 68078861AA, 68001696AA, 56053030AB, 68001696AB, 68078861AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2014 Dodge Avenger | Express, Heat, Lux, Mainstreet, R/T, SE, SXT, SXT Plus | 2.4L L4, 2.7L V6, 3.5L V6, 3.6L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX
View related parts
Dodge Avenger TPMS Sensor Part Number: 68078768AC
$48.91 MSRP: $105.00
You Save: $56.09 (54%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Tire Pressure; Tire Pressure Monitoring System Sensor; TPMS Sensor Service Kit; Tire Pressure Sensor; Pressure Sensor; Sensor
- Replaces: 68001698AB, 56053031AB, 68001698AC, 68078768AA, 56053031AC, 56029527AA, 68078768AB, 68001698AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2013 Dodge Avenger | R/T, SE, SXT, SXT Plus | 4 Cyl 2.4 L GAS, 6 Cyl 3.6 L FLEX

Dodge Avenger TPMS Sensor

Choose OEM TPMS Sensor that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each TPMS Sensor follows strict manufacturing steps to lock in quality and fit. If your Dodge Avenger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Avenger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The TPMS Sensor is a critical part of the Dodge Avenger since it works to offer precise tire pressure monitoring that is vital to the performance of Dodge Avenger automobiles. Special sensor of the TPMS is installed in each Dodge Avenger and the mentioned sensors can be of clamp-in, screw-in or snap-in types. The specific Dodge Avenger models operate with either the iTPMS or dTPMS technology, with the latter characterised by real time pressure data for up to sixty four tires to deliver maximum safety and performance results. As for the basic functionalities, iTPMS provides simplicity of the interface, on the other hand, there is dTPMS which is notable for the possibility to receive accurate measurements. Functionality, power and efficiency are displayed in the Dodge Avenger models, discussing how the car stands out from the others. The TPMS Sensor is a critical factor in improving the well-being of vehicles by eliminating other issues that affect tires hence safety. Also, the Dodge Avenger TPMS Sensor supports numerous Avenger models; thus, drivers can keep their vehicles' parameters and safety levels optimal. Through the integrated safety features of the product, TPMS has become a quality product that is accepted in the market which in turn strengthens the brand identity of Dodge car. Therefore, the Dodge Avenger TPMS Sensor is not just a component, but a valuable assistant in ensuring secure and optimized driving.

Dodge Avenger TPMS Sensor Parts and Q&A

TPMS Sensor
68078861AC
Q: How to Install a TPMS Sensor on Dodge Avenger?
A:
You should start by removing old seal 2 and metal washer 1 and replace them at the bottom of the sensor valve stem 6 before fitting the sensor. Clean all around the sensor/valve mounting area in wheel 5, so the wheel surface is spotless. Be careful not to press the sensor antenna strap, so press near metal valve stem 2 as you move the sensor into the wheel from inside. Put washer 3 and sensor nut 3 into place by hand, then push down on the sensor housing 2 to make it join with the interior of the wheel; then tighten sensor nut 3 to 8 Nm-71 in. lbs. Make sure not to crank the sensor nut too carefully, since it might result in the sensor separating from the valve. For rotating wheel tire changers, place the sensor valve stem 2 approximately 280° away from the head of the changer. For rotating tool tire changers, position it 210° to the right away from the mounting/dismounting tool and be sure the sensor is clear of the lower part of the bead breaker. Make the tire pressure fit the instructions on the Tire Pressure Label and be sure the original valve stem cap is properly fixed. Affix the tire and wheel assembly to the vehicle, get rid of the support and lower down the car. Use TPM-RKE Analyzer, 9936, to program the tire pressure sensor ID into the WCM/SKREEM or just drive above 15 mph (24 km/h) for 10 minutes after the car has been at rest for at least 20 minutes. If a sensor can't be programmed to the correct signal strength, follow the diagnostic requirements.