How to Detach the Drive Shaft on Dodge Sprinter 3500?

Before you take out the propeller shaft, secure your vehicle in place to keep it from rolling. Glue thin lines on both sides of the propeller shaft to mark the correct position. Remove the intermediate bearing nuts from the retaining bracket as well as the bracket used in the brake cable, next. After that, take out the bracket bolts. Following that, take out the rear axle and transmission propeller shaft bolts from the propeller flange. Your last step should be to take out the shaft of the engine.

How to Service and Repair a Drive Shaft on Dodge Sprinter 3500?

Before you start on the propeller shaft, place the car in neutral, lift it and level out the axles. Uninstall the universal joint snap rings to provide a better, flat fit for the Inclinometer 7663 base if equipped. Turn the shaft so that the transmission case output yoke bearing is located down below the vehicle. It's important to measure both from front to rear and from only one side of the car at a time. Set the Inclinometer 7663 face down on the yoke bearing beside the shaft, so it's parallel, make sure the bubble inside the sight glass falls dead middle and record this angle for the Output Angle reading. After that, turn the propeller shaft 90 degrees and rest the inclinometer on the yoke bearing so the bubble falls in the middle. Read the recorded value for the Propeller Shaft Angle. Following the previous steps, turn the propeller shaft 90 degrees more and place the inclinometer on the boss bearing so that its bubble is in the center. This gives you the Pinion Boss Input Angle. The Transmission Output Operating Angle is found by subtracting the smaller figure (A) from the larger (C) and the axle Input Operating Angle is obtained by subtracting the smaller (B) from the larger (C). Cancellation should be less than 1 degree, operating angles less than 3 degrees, and the continuous operating angle should be at least 1 degree higher. Both two-piece and three-piece propeller shaft angles are measured in the same way as a single-piece shaft.

OEM Dodge Sprinter 3500 Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Drive Shafts found

View related parts
Dodge Sprinter 3500 Drive Shaft Part Number: 68056107AA
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 68056112AA, 68006640AA, 68006641AA, 68006658AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2009 Dodge Sprinter 3500 | Base | 3.0L V6, 3.5L V6, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.5 L GAS
View related parts
Dodge Sprinter 3500 Drive Shaft Part Number: 5129034AA
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive 2 Piece
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2006 Dodge Sprinter 3500 | Base | 5 Cyl 2.7 L DIESEL
View related parts
Dodge Sprinter 3500 Drive Shaft Part Number: 5119086AA
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive 2 Piece
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2006 Dodge Sprinter 3500 | Base | 5 Cyl 2.7 L DIESEL
View related parts
Dodge Sprinter 3500 Drive Shaft Part Number: 68138113AA
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 68006638AA, 68047594AA, 68056139AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Dodge Sprinter 3500 | Base | 3.5L V6, 6 Cyl 3.5 L GAS
View related parts
Dodge Sprinter 3500 Drive Shaft Part Number: 5104083AA
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear, Front Section
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2006 Dodge Sprinter 3500 | Base | 5 Cyl 2.7 L DIESEL
View related parts
Dodge Sprinter 3500 Drive Shaft Part Number: 68055987AA
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 68006622AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2009 Dodge Sprinter 3500 | Base | 3.0L V6, 6 Cyl 3.0 L DIESEL
View related parts
Dodge Sprinter 3500 Drive Shaft Part Number: 5104084AA
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear, Rear Section
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2006 Dodge Sprinter 3500 | Base | 5 Cyl 2.7 L DIESEL
View related parts
Dodge Sprinter 3500 Drive Shaft Part Number: 68138114AA
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 68056138AA, 68006637AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2009 Dodge Sprinter 3500 | Base | 3.0L V6, 6 Cyl 3.0 L DIESEL
View related parts
Dodge Sprinter 3500 Drive Shaft Part Number: 68056147AA
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 68055991AA, 68006632AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Dodge Sprinter 3500 | Base | 6 Cyl 3.5 L GAS

Dodge Sprinter 3500 Drive Shaft

Choose OEM Drive Shaft that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Drive Shaft follows strict manufacturing steps to lock in quality and fit. If your Dodge Sprinter 3500 matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Sprinter 3500 parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Dodge Sprinter 3500 Drive Shaft is one of the crucial components in the automotive market, incorporated for the proper delivery of power and Torque to the drive wheels from the engine. This part is a critical link compromising of other powertrain parts to deliver adequate power for different models of the Sprinter 3500. Being a Dodge Sprinter 3500 Drive Shaft, it is designed to be extremely strong and offer high torsional capacity as well as shear strength and yet a relatively lightweight to help the vehicle run more efficiently. This Drive Shaft comes in one piece, two-part, and slip-in-tube design and is suited for two-wheel and all-wheel applications of Dodge Sprinter 3500 manufactured from 2003-2009. The contribution to the overall safety cannot be overemphasized; since a faulty or, for that matter, efficient Drive Shaft affects the car's steadiness and stable performance in any driving conditions. More to note, the Dodge Sprinter 3500 Drive Shaft is also compatible with modern drivetrain layouts and, in particular, front wheel drive layouts which take its performance to the next level. The towing capacity of this vehicle is 5,000 pounds besides, the fuel efficiency is considerably at about 25 mpg; among these the Dodge Sprinter 3500 Drive Shaft is an important part which adds efficiency and safety to the vehicle. The above mentioned features enhances the trustworthiness of Dodge Sprinter 3500 Drive Shaft in commercial as well as individual market.

Dodge Sprinter 3500 Drive Shaft Parts and Q&A

Drive Shaft
68056107AA
Q: How to Detach the Drive Shaft on Dodge Sprinter 3500?
A:
Before you take out the propeller shaft, secure your vehicle in place to keep it from rolling. Glue thin lines on both sides of the propeller shaft to mark the correct position. Remove the intermediate bearing nuts from the retaining bracket as well as the bracket used in the brake cable, next. After that, take out the bracket bolts. Following that, take out the rear axle and transmission propeller shaft bolts from the propeller flange. Your last step should be to take out the shaft of the engine.
Drive Shaft
5119086AA
Q: How to Service and Repair a Drive Shaft on Dodge Sprinter 3500?
A:
Before you start on the propeller shaft, place the car in neutral, lift it and level out the axles. Uninstall the universal joint snap rings to provide a better, flat fit for the Inclinometer 7663 base if equipped. Turn the shaft so that the transmission case output yoke bearing is located down below the vehicle. It's important to measure both from front to rear and from only one side of the car at a time. Set the Inclinometer 7663 face down on the yoke bearing beside the shaft, so it's parallel, make sure the bubble inside the sight glass falls dead middle and record this angle for the Output Angle reading. After that, turn the propeller shaft 90 degrees and rest the inclinometer on the yoke bearing so the bubble falls in the middle. Read the recorded value for the Propeller Shaft Angle. Following the previous steps, turn the propeller shaft 90 degrees more and place the inclinometer on the boss bearing so that its bubble is in the center. This gives you the Pinion Boss Input Angle. The Transmission Output Operating Angle is found by subtracting the smaller figure (A) from the larger (C) and the axle Input Operating Angle is obtained by subtracting the smaller (B) from the larger (C). Cancellation should be less than 1 degree, operating angles less than 3 degrees, and the continuous operating angle should be at least 1 degree higher. Both two-piece and three-piece propeller shaft angles are measured in the same way as a single-piece shaft.