JeepParts
My Garage
My Account
Cart
OEM Chrysler 300 Center Console Base
- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
11 Center Console Bases found
Chrysler 300 Base, Center Part Number: 1LD99DX9AA
$35.47 MSRP: $204.00You Save: $168.53 (83%)Ships in 1-2 Business Days
Chrysler 300 Console Body, Center Part Number: 68270656AE
$152.96 MSRP: $226.00You Save: $73.04 (33%)Ships in 1-3 Business Days
Chrysler 300 Console Assembly, Beige, Center Part Number: 1PJ85HL1AH
Chrysler 300 Console Assembly, Black, Center Part Number: 1PJ85DX9AH
Chrysler 300 Console Assembly, Beige, Center Part Number: 1JN68HL1AG
Chrysler 300 Console Assembly, Black, Center Part Number: 1JN68DX9AG
Chrysler 300 Floor Console, Center Part Number: 1BX61XDVAA
Chrysler 300 Floor Console, Gray, Center Part Number: 1BX611P7AA
Chrysler 300 Floor Console, Gray Part Number: 1AJ731P7AA
Chrysler 300 Floor Console, Gray Part Number: 1AJ731D5AA
Chrysler 300 Floor Console, Dark Gray, Center Part Number: 1AJ731D1AA
Chrysler 300 Center Console Base
Choose OEM Center Console Base that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Center Console Base follows strict manufacturing steps to lock in quality and fit. If your Chrysler 300 matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine 300 parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.
Chrysler 300 Center Console Base Parts and Q&A
- Q: How to Install a Center Console Base on Chrysler 300?A:Position the floor console back far enough that you can reach and attach the jumper wire to the accessory power outlet under the console and if there is a heated seat in the rear, connect the connector as well. Jam one side of the console into its slot on the lower panel, then use the front of the console to place the ears in the openings at the front of the panel. You should then see two alignment holes on the console matching up with the two pins on the instrument panel. Push the pin on the rear of the console into the dark hole behind your steering wheel and install and tighten both front screws to 3 Nm (23 in. lbs.). Following this, install and secure the three 8 mm bolts into the rear bin that connect the console to the floor panel transmission tunnel by turning them to 5 Nm (40 in. lbs.). Put the console shifter bezel over the gear selector lever so the tabs match the holes in the floor console, add the two screws at the front to hold it and tighten them to 3 Nm (23 in. lbs.). In the back of the console, set the mat so its curve is facing forward and, in the front of the console, place it in the cubby bin. Drop the shifter trim ring all the way to its position, then move the gear selector lever into the Park spot. For cars which have Automatic Express Up power windows, any time the door module's power is interrupted, calibration is required and the battery reconnect procedure must also be performed after disconnecting the battery. Lastly, hook the negative Battery Cable back to the car. For the install, attach the center console cover with DVD, tighten it using six screws and set the side covers in place.
- Q: How to Remove the Center Console Base and Floor Console with DVD Cover on Chrysler 300?A:First, use the parking brake, put the Ignition Switch on, press the service brakes, use Neutral and turn the ignition off again before releasing the service brakes. In an Automatic Express Up vehicle, do a calibration for this feature after a module loss power out and reconnect the battery if the battery was not connected during the event. Take out the battery's negative cable and next, separate and disconnect the retaining ring at the base of the gear shifter with a small flat bladed tool before pulling it down the shaft. Press the shifter knob up and then slide it out of the shifter shaft. After opening the lid of the rear bin, take out the mat from inside the cubby bin on the front of the floor console and then from the bin at the back. Unscrew both screws holding the front part of the shifter bezel to the console and then unsnap the bezel with an insert trim stick. Slide out the floor console by first removing the 8 mm bolts from the rear bin mounting points and then the two screws from the mounting brackets at the front of the console against the instrument panel. Gently pull the vehicle's console back and disconnect its jumper wire from the bottom accessory outlet. If you have a rear heated seat, disconnect its connector as well before taking out the console from the cabin. To get your Center Console Cover with DVD out, open the console top, remove the side covers, remove six screws and then take off the cover.
