How to Remove the Right and Left Exhaust Manifold on Chrysler Aspen?

After you pull out the negative cable from the battery's terminal, take out the air cleaner assembly, resonator assembly and air inlet hose. Then, pull off the accessory drive belt and next take out the A/C compressor and the A/C accumulator support bracket fastener. Draw out the coolant up to the level of the car's heater hoses and then unhook the hoses from the engine side. Unscrew or pull off the fasteners that hold the exhaust manifold heat shield and take out the heat shield as well. Take off all the fasteners that hold the upper exhaust manifold in place, lift the car on a hoist, disconnect the exhaust pipe from the manifold and remove the fasteners holding the starter in position. Remove the lower mounting bolts from the exhaust manifold and pull the manifold and gasket out from below the engine area. After removing the negative cable from the battery, jerk the end of the lift up to turn the vehicle so you can work comfortably below and on top of the engine. Peel back the flex pipe at the manifold, have the vehicle lowered, securely hold it down and unfasten the heat shield in the front. Afterward, lift the vehicle again and do the same for the rear heat shield fasteners. Take off the heat shield, lower the vehicle and take away the upper exhaust manifold retaining bolts. Rise the vehicle for the second time and now remove the lower retaining bolts of the exhaust manifold. Remove the exhaust manifold and gasket from below the engine compartment.

How to Install an Exhaust Manifold Correctly on Chrysler Aspen?

For proper installation of the exhaust manifold, set both the exhaust manifold and the gasket beneath the engine, then put in the lower fasteners one at a time, without tightening the bolts before all are set. Fix each bolt in the upper manifold, starting in the middle of the manifold and tightening outward to a pressure of 25 Nm (18 ft. lbs.). Make sure the fasteners of the heat shield are not overtightened, since this may cause it to bend or crack. Then, install the exhaust manifold heat shield and secure the fasteners to 8 Nm (72 in. lbs.), then lose them by 45 degrees. Mount the starter, fasteners and exhaust pipe to the manifold and add the heater hoses at the engine. Place the A/C accumulator fastener and then screw the A/C compressor and its fasteners as well. Replace the accessory belt, then fix the air cleaner assembly, the resonator assembly and the air inlet hose. Connect the wires and install the battery in the end. After completing the right exhaust manifold installation, connect the negative cable to the battery and make sure all steps are the same for the left exhaust manifold.

OEM Chrysler Aspen Exhaust Manifold

Engine Exhaust Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Exhaust Manifolds found

View related parts
Chrysler Aspen Exhaust Manifold, Driver Side Part Number: 53032437AD
$493.09 MSRP: $892.00
You Save: $398.91 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left
- Position: Driver Side
- Replaces: 53032437AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Chrysler Aspen | Limited | 5.7L V8, 8 Cyl 5.7 L GAS
View related parts
Chrysler Aspen Exhaust Manifold, Passenger Side Part Number: 68045560AB
$49.01 MSRP: $70.75
You Save: $21.74 (31%)
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right; Exhaust Manifold Gasket; Manifold Gasket; Manifold; Manifold Exhaust
- Position: Passenger Side
- Replaces: 53034138AC, 68045560AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Chrysler Aspen | Limited, Limited Hybrid | 5.7L V8, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
View related parts
Chrysler Aspen Exhaust Manifold, Driver Side Part Number: 53032901AG
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left; Manifold; Manifold Exhaust
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Chrysler Aspen | Limited | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Chrysler Aspen Exhaust Manifold, Passenger Side Part Number: 53030808AD
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right; Exhaust Manifold Gasket; Manifold Gasket; Manifold; Manifold Exhaust
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Chrysler Aspen | Limited | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Chrysler Aspen Exhaust Manifold, Driver Side Part Number: 53030809AD
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left; Manifold; Manifold Exhaust
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Chrysler Aspen | Limited | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Chrysler Aspen Exhaust Manifold, Driver Side Part Number: 68045437AB
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left; Manifold; Manifold Exhaust
- Position: Driver Side
- Replaces: 68045437AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Chrysler Aspen | Limited | 8 Cyl 4.7 L FLEX
View related parts
Chrysler Aspen Exhaust Manifold, Passenger Side Part Number: 68045438AB
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right; Manifold; Manifold Exhaust
- Position: Passenger Side
- Replaces: 68045438AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Chrysler Aspen | Limited | 8 Cyl 4.7 L FLEX
View related parts
Chrysler Aspen Exhaust Manifold, Passenger Side Part Number: 53032198AZ
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right; Manifold
- Position: Passenger Side
- Replaces: 53032198AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Chrysler Aspen | Limited | 5.7L V8, 8 Cyl 5.7 L GAS
View related parts
Chrysler Aspen Exhaust Manifold, Passenger Side Part Number: 53032898AF
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right; Manifold; Manifold Exhaust
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Chrysler Aspen | Limited | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Chrysler Aspen Exhaust Manifold Part Number: 68045559BB
$40.60 MSRP: $59.60
You Save: $19.00 (32%)
Product Specifications
- Other Name: Manifold - Exhaust; Manifold Gasket; Manifold
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Chrysler Aspen | Limited, Limited Hybrid | 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS

Chrysler Aspen Exhaust Manifold

Choose OEM Exhaust Manifold that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Exhaust Manifold follows strict manufacturing steps to lock in quality and fit. If your Chrysler Aspen matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Aspen parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The product called the Chrysler Aspen Exhaust Manifold is a crucial part that considerably influences the vehicle's capabilities and performance. Economically recognized for its stability, the Exhaust Manifold does a great job in the channeling of hot exhaust gases produced by the engine to the exhaust system and hence enhances the performance of the engine while at the same time reducing hazardous emission. Chrysler Aspen is a full-size luxury SUV with powerful driving dynamics and towing capability that makes this feature valuable for the car. Suits different Aspen models, the Standard 4.7L V8 and the beefed-up 5.7L HEMI V8, the Exhaust Manifold is specifically tasked with the responsibility of maintaining an optimal air to fuel ratio, one that is imperative in producing the power, while at the same time preventing disasters. Made from high quality materials such as cast iron or stainless steel, and having the ability to resist high temperatures and develop a layer of oxidation, the Chrysler Aspen Exhaust Manifold is built to be long lasting. In the same prospect, the manifold is designed in a way that reduces flow resistance hence increasing the velocity of the exhaust gases that has a knock on the effect of increasing fuel efficiency. Looking at the Exhaust Manifold component the Chrysler Aspen can be deemed as being highly rigorous in terms of quality and engineering. For it is notable that Chrysler Aspen Exhaust Manifold is one of the key elements ensuring the car's enhanced power and vectors together with security and fuel efficiency; in this context, it is possible to ascertain that Chrysler Aspen Exhaust Manifold plays a crucial role in the car's performance, and this fact proves once again that Chrysler Aspen is a reliable and effective SUV.

Chrysler Aspen Exhaust Manifold Parts and Q&A

Exhaust Manifold, Driver Side
53032437AD
Q:
How to Remove the Right and Left Exhaust Manifold on Chrysler Aspen?
A:
After you pull out the negative cable from the battery's terminal, take out the air cleaner assembly, resonator assembly and air inlet hose. Then, pull off the accessory Drive Belt and next take out the A/C compressor and the A/C accumulator support bracket fastener. Draw out the coolant up to the level of the car's heater hoses and then unhook the hoses from the engine side. Unscrew or pull off the fasteners that hold the exhaust manifold heat shield and take out the heat shield as well. Take off all the fasteners that hold the upper exhaust manifold in place, lift the car on a hoist, disconnect the Exhaust Pipe from the manifold and remove the fasteners holding the Starter in position. Remove the lower mounting bolts from the exhaust manifold and pull the manifold and gasket out from below the engine area. After removing the negative cable from the battery, jerk the end of the lift up to turn the vehicle so you can work comfortably below and on top of the engine. Peel back the flex pipe at the manifold, have the vehicle lowered, securely hold it down and unfasten the heat shield in the front. Afterward, lift the vehicle again and do the same for the rear heat shield fasteners. Take off the heat shield, lower the vehicle and take away the upper exhaust manifold retaining bolts. Rise the vehicle for the second time and now remove the lower retaining bolts of the exhaust manifold. Remove the exhaust manifold and gasket from below the engine compartment.
Exhaust Manifold, Passenger Side
68045438AB
Q:
How to Install an Exhaust Manifold Correctly on Chrysler Aspen?
A:
For proper installation of the exhaust manifold, set both the exhaust manifold and the gasket beneath the engine, then put in the lower fasteners one at a time, without tightening the bolts before all are set. Fix each bolt in the upper manifold, starting in the middle of the manifold and tightening outward to a pressure of 25 Nm (18 ft. lbs.). Make sure the fasteners of the heat shield are not overtightened, since this may cause it to bend or crack. Then, install the exhaust manifold heat shield and secure the fasteners to 8 Nm (72 in. lbs.), then lose them by 45 degrees. Mount the Starter, fasteners and Exhaust Pipe to the manifold and add the heater hoses at the engine. Place the A/C Accumulator fastener and then screw the A/C compressor and its fasteners as well. Replace the accessory belt, then fix the air cleaner assembly, the resonator assembly and the air inlet hose. Connect the wires and install the battery in the end. After completing the right exhaust manifold installation, connect the negative cable to the battery and make sure all steps are the same for the left exhaust manifold.