How to Properly Install Battery Cables in the Engine Compartment on Dodge Caliber?

Put the battery cables into the engine compartment, then install the battery cable pushpins, fasteners and routing clips from black to red, until they are in place. Bind the battery cable to the B+ terminal of the starter motor after tightening the nut to 13 Nm (115 in. lbs.) and do the same for the connection to the B+ terminal of the generator (14 Nm or 125 in. lbs.). Wrap the negative cable around the body ground stud with nut (1) and tighten it down to 12 Nm (9 ft. lbs.). Note that gasoline and diesel engine vehicles have their battery polarity opposite to each other, so check the locations of each cable before handling the battery. After you've connected the plus side of the battery, hook up the minus side, fasten the cable clamp nuts down to 5 Nm (45 in. lbs.). Add nut (2) to make sure TIPM cable (1) is securely attached to battery clamp stud (5), then secure air cleaner fresh air duct (2) by turning retaining clips (3).

How to Maintain Battery Cables on Dodge Caliber?

You should start by disconnecting and isolating the negative battery cable. After that, simply rotate the retainers and take out the air cleaner fresh air duct. Note that the polarity of the cables used for batteries on gasoline and diesel vehicles is not the same, so first check the cables before beginning any work on the battery. Take out the nut securing the Totally Integrated Power Module (TIPM) cable to the battery clamp stud and then disconnect along with remove the negative and positive cables from the battery. Unscrew the nut holding the negative cable to the body ground stud and remove both battery cables from the B+ terminals of the generator and the starter motor. Work your way through disconnecting the battery retaining devices, pushpins and clips on the cables and finally remove them from the engine.

OEM Dodge Caliber Battery Cable

Car Battery Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Battery Cables found

View related parts
Dodge Caliber Wire Harness Part Number: 4801329AD
$40.30 MSRP: $59.20
You Save: $18.90 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wiring - Battery Feed; Battery Cables; Battery Cable; Wiring Battery Feed
- Replaces: 4801329AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2012 Dodge Caliber | Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, SXT Plus, Uptown | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Wiring Harness Part Number: 68058200AB
Product Specifications
- Other Name: Wiring - Battery; Battery Cables; Ground Strap; Battery Cable; Positive Cable; Negative Cable; Wiring Battery
- Replaces: 68058200AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010-2012 Dodge Caliber | Express, Heat, Mainstreet, R/T, Rush, SE, SXT, SXT Plus, Uptown | 1.8L L4, 2.0L L4, 2.4L L4, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Wiring Harness Part Number: 5148444AA
Product Specifications
- Other Name: Wiring - Battery; Battery Cables; Ground Strap; Battery Cable; Positive Cable; Negative Cable; Wiring Battery
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Dodge Caliber | R/T, SE, SRT-4, SXT | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Wiring Harness Part Number: 4795318AE
Product Specifications
- Other Name: Wiring - Battery; Battery Cables; Ground Strap; Battery Cable; Positive Cable; Negative Cable; Wiring Battery
- Replaces: 4795318AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Dodge Caliber | R/T, SE, SRT-4, SXT | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Wiring Harness Part Number: 5035047AA
Product Specifications
- Other Name: Battery; Wiring Battery
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Dodge Caliber | SRT-4 | 4 Cyl 2.4 L GAS

Dodge Caliber Battery Cable

Choose OEM Battery Cable that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Battery Cable follows strict manufacturing steps to lock in quality and fit. If your Dodge Caliber matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Caliber parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Dodge calibe battery cable is a very important part of automatic car and its flows current from the battery side to the vehicle starter for igniting the engine. The Dodge Caliber Battery Cable is indispensable because this component is used for getting a good contact that helps to avoid potential starting problems and failures. Unfortunately, the battery cables wear out and corrode with time and can, therefore, require replacement from time to time, thus the importance of the Dodge Caliber owners to conduct regular checks on the cables. This regular check-up also has added advantage of increasing the efficiency of the car because a Dodge caliber should be in its optimum state at all times. These battery cables fit different models of the Dodge Caliber especially the SE and the SXT, because they are made in such a way that they will serve the different models in the right way. Conspicuously, it might be crucial to accentuate that the Dodge Caliber Battery Cable offered on the market is characterized by very high quality construction and optimized conductivity thus contributing to the minimization of possibilities of electrical failures in the vehicle. The Dodge Caliber Battery Cable is a recommended product that will be useful for the owners of cars of this brand who want to increase the durability of their vehicle. Therefore, when selecting the appropriate Dodge Caliber Battery Cable, the driver can always be able to rely and have a safe car on road.

Dodge Caliber Battery Cable Parts and Q&A

Wire Harness
4801329AD
Q: How to Properly Install Battery Cables in the Engine Compartment on Dodge Caliber?
A:
Put the battery cables into the engine compartment, then install the battery cable pushpins, fasteners and routing clips from black to red, until they are in place. Bind the battery cable to the B+ terminal of the starter motor after tightening the nut to 13 Nm (115 in. lbs.) and do the same for the connection to the B+ terminal of the generator (14 Nm or 125 in. lbs.). Wrap the negative cable around the body ground stud with nut (1) and tighten it down to 12 Nm (9 ft. lbs.). Note that gasoline and diesel engine vehicles have their battery polarity opposite to each other, so check the locations of each cable before handling the battery. After you've connected the plus side of the battery, hook up the minus side, fasten the cable clamp nuts down to 5 Nm (45 in. lbs.). Add nut (2) to make sure TIPM cable (1) is securely attached to battery clamp stud (5), then secure air cleaner fresh Air Duct (2) by turning retaining clips (3).
Wiring Harness
5148444AA
Q: How to Maintain Battery Cables on Dodge Caliber?
A:
You should start by disconnecting and isolating the negative battery cable. After that, simply rotate the retainers and take out the air cleaner fresh Air Duct. Note that the polarity of the cables used for batteries on gasoline and diesel vehicles is not the same, so first check the cables before beginning any work on the battery. Take out the nut securing the Totally Integrated Power Module (TIPM) cable to the battery clamp stud and then disconnect along with remove the negative and positive cables from the battery. Unscrew the nut holding the negative cable to the body ground stud and remove both battery cables from the B+ terminals of the generator and the starter motor. Work your way through disconnecting the battery retaining devices, pushpins and clips on the cables and finally remove them from the engine.