How to Service a Driveshaft Center Support Bearing on Dodge Challenger?

To service the driveshaft center support bearing, remove the propeller shaft from the vehicle and watch for the skip-tooth design on the interface, since this will ensure the propeller shaft can only be installed one way; installation markings are provided only to assist with installation. After that, mark points 2 and 3 on each column with installation reference marks. Part the front and rear segments of the propeller shaft at the bearing and then take out boot 1. After that, fit Bearing 1 onto the rear shaft segment using the Arbor Press and Bearing Splitter 1130.

How to Install a Driveshaft Center Support Bearing on Dodge Challenger?

Start by placing the rear part of the propeller shaft into a press and keeping it supported by the joint yoke. After that, put the Driveshaft Center Support Bearing assembly onto the shaft. Secure the Driveshaft Center Support Bearing assembly to the shaft by pressing it using installer C-4735. After taking off the propeller shaft from the press, add boot 1 to the aft end of the shaft. Because the skip-tooth design is used for the propeller shaft spline, there is only one correct way to place the propeller and shaft, to avoid imbalance. Bring the index marks together from your aborted attempt and slide the front section onto the rear section. After that, put boot 2 onto the front section and make sure it is into the groove marked 3. After all the other work is done, replace the propeller shaft.

OEM Dodge Challenger Driveshaft Center Support Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Driveshaft Center Support Bearings found

View related parts
Dodge Challenger Center Bearing Part Number: 5161435AA
$364.11 MSRP: $534.00
You Save: $169.89 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing - Drive Shaft; Drive Shaft Center Support Bearing; Driveshaft Center Support Bearing; Bearing Drive Shaft
- Replaces: 5142476AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010-2014 Dodge Challenger | R/T, R/T Classic, Rallye Redline, SE, SRT8, SXT, SXT Plus | 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Center Bearing Part Number: 68043376AA
Product Specifications
- Other Name: Bearing - Drive Shaft; Drive Shaft Center Support Bearing; Driveshaft Center Support Bearing; Bearing Drive Shaft
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2014 Dodge Challenger | R/T, R/T Classic, Rallye Redline, SE, SRT8, SXT, SXT Plus | 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.4 L GAS

Dodge Challenger Driveshaft Center Support Bearing

Choose OEM Driveshaft Center Support Bearing that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Driveshaft Center Support Bearing follows strict manufacturing steps to lock in quality and fit. If your Dodge Challenger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Challenger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Dodge Challenger Driveshaft Center Support Bearing serves as a critical system component that serves to increase Dodge Challenger reliability and drive performance by distributing motor power from transmission to rear axle when the vehicle operates using a rear-wheel drive. This vital part maintains the front portion of a two-piece driveshaft whereas it enables the required flexibility together with stability throughout driveshaft pivoting motions during suspension movement. A Driveshaft Center Support Bearing works with multiple Dodge Challenger editions because it welcomes both U-Joints and double cardan joints as flexible joints to minimize vibrations and maintain driving comfort. This support bearing maintains its position as one of the lasting Dodge Challenger components through its ability to tolerate regular usage but users must conduct regular maintenance to stop problematic vibrations and noise that occur mainly at high speeds. The Dodge Challenger benefits in two ways from this component since it makes the vehicle more efficient and plays an essential role in preventing unsafe driving conditions. The Driveshaft Center Support Bearing stands out in automotive markets through its strong design and universal joint adaptability which makes it a highly recommended option for driving enthusiasts and regular car operators. Dodge Challenger Driveshaft Center Support Bearing showcases the automaker's established commitment toward quality performance which earns lasting favor from car enthusiasts.

Dodge Challenger Driveshaft Center Support Bearing Parts and Q&A

Center Bearing
5161435AA
Q: How to Service a Driveshaft Center Support Bearing on Dodge Challenger?
A:
To service the driveshaft center support bearing, remove the propeller shaft from the vehicle and watch for the skip-tooth design on the interface, since this will ensure the propeller shaft can only be installed one way; installation markings are provided only to assist with installation. After that, mark points 2 and 3 on each column with installation reference marks. Part the front and rear segments of the propeller shaft at the bearing and then take out boot 1. After that, fit Bearing 1 onto the rear shaft segment using the Arbor Press and Bearing Splitter 1130.
Center Bearing
68043376AA
Q: How to Install a Driveshaft Center Support Bearing on Dodge Challenger?
A:
Start by placing the rear part of the propeller shaft into a press and keeping it supported by the joint yoke. After that, put the Driveshaft Center Support Bearing assembly onto the shaft. Secure the Driveshaft Center Support Bearing assembly to the shaft by pressing it using installer C-4735. After taking off the propeller shaft from the press, add boot 1 to the aft end of the shaft. Because the skip-tooth design is used for the propeller shaft spline, there is only one correct way to place the propeller and shaft, to avoid imbalance. Bring the index marks together from your aborted attempt and slide the front section onto the rear section. After that, put boot 2 onto the front section and make sure it is into the groove marked 3. After all the other work is done, replace the propeller shaft.