How to Service and Repair a Parking Brake Cable for Front on Dodge Challenger?

Service the front parking brake cable by first lifting and supporting the vehicle. You sometimes need to lock out the parking brake lever, since the lever has only a short travel and tends to stay up because of low tension. Untie the cable under the front parking brake (5) from the connector (3) linked to the rear cable (4) above the axle. Detach the front cable (3) from the equalizer (2), then remove screw (2) securing the cable (1) routing bracket to the rear crossmember front flange (3). After that, unfasten the nuts (1), bolt (2) and push-pins (4) holding the lower rear wheelhouse shield (3) to the vehicle body and remove the shield afterward. Unscrew the screw (6) and remove the routing clip (4) nuts from cable (7) under the body (3) before you lower the vehicle. Get rid of the driver door opening sill scuff plate and cowl side trim and pull the carpet at the front to reach the cable. The cable at the lever should not be taken off from the parking brake connector unless it is secured, because it might end up inside the housing. Pull downward on the connector with the pliers and secure it in the parking brake lever bracket's retaining fork. Lift the front parking brake cable strand (1) off the cable connector (2) which is kept in place by the retaining fork. Grasp the cable retainer at the lever bracket with a 13 mm 12-point box wrench (2) and rotate again to collapse the fingers. While the fingers are collapsed, pull the cable from the bracket. Then, unclip the parking brake cable grommet (2) from the floor pan (3) and remove the parking brake cable (7) through the hole from under the vehicle.

How to Install a Parking Brake Cable for the Rear on Dodge Challenger?

Route the leading part of the rear parking brake cable up through the cable guide on the crossmember, pass it through the crossmember bracket by the equalizer and press the retainer into the bracket to secure the cable. Take the cable end without the spring and guide it through the rear knuckle (3). Use the supplied handle and tighten the screw firmly so that the torque indicator reads 8 Nm (71 in. lbs.). Fit the parking brake cable end with the actuator lever (1), so that word UP is facing outside and put in the parking brake shoes as well as the necessary supporting components. This service on the parking brake can be done without having to lock out the parking brake lever, thanks to the car's short travel and weak springs. Attach the rear parking brake cable at the equalizer/front cable by linking the left cable (1) at the equalizer (2) above the rear axle differential and rear crossmember (6) or by linking the right cable (4) at connector (3) above the rear axle differential and rear crossmember (6). Wheels just above the floor-yes, that's the spot-parking brake up, press it, lower it and press again. Apply the lever to check if the rear wheels can move freely and after releasing the lever, see if the rotation of the rear wheels is unhassled. Adjust the parking brake shoes as needed and lower the vehicle after that.

OEM Dodge Challenger Parking Brake Cable

Emergency Parking Brake Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Parking Brake Cables found

View related parts
Dodge Challenger Front Cable Part Number: 4779591AH
$71.42 MSRP: $109.00
You Save: $37.58 (35%)
ADD TO CART
Product Specifications
- Other Name: Cable - Parking Brake; Brake Cable; Cable Parking Brake
- Replaces: 4779591AF, 4779591AG, 4779591AE, 4779591AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2023 Dodge Challenger | 392 Hemi Scat Pack Shaker, GT, R/T, R/T 392, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, R/T Shaker, Rallye Redline, SE, SRT 392, SRT Demon, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock, SRT8, SXT, SXT Plus, Scat Pack, T/A, T/A 392, T/A 392 Widebody | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Rear Cable Part Number: 4779592AF
$28.69 MSRP: $42.80
You Save: $14.11 (33%)
ADD TO CART
Product Specifications
- Other Name: Cable - Parking Brake; Brake Cable; Cable Parking Brake
- Replaces: 4779592AD, 4779592AB, 4779592AC, 4779592AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2023 Dodge Challenger | 392 Hemi Scat Pack Shaker, GT, R/T, R/T 392, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, R/T Shaker, Rallye Redline, SE, SRT 392, SRT Demon, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock, SRT8, SXT, SXT Plus, Scat Pack, T/A, T/A 392, T/A 392 Widebody | 3.6L V6, 5.7L V8, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Rear Cable Part Number: 5290824AB
$48.39 MSRP: $70.85
You Save: $22.46 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable - Parking Brake; Brake Cable; Cable Parking Brake
- Replaces: 5290824AA, 4779260AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Challenger | SRT8 | 8 Cyl 6.1 L GAS
View related parts
Dodge Challenger Rear Cable Part Number: 4779973AD
$69.41 MSRP: $105.00
You Save: $35.59 (34%)
ADD TO CART
Product Specifications
- Other Name: Cable - Parking Brake; Brake Cable; Cable Parking Brake
- Replaces: 4779973AC, 4779973AA, 4779973AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2023 Dodge Challenger | 392 Hemi Scat Pack Shaker, GT, R/T, R/T 392, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, R/T Shaker, Rallye Redline, SE, SRT 392, SRT Demon, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock, SRT8, SXT, SXT Plus, Scat Pack, T/A, T/A 392, T/A 392 Widebody | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Rear Cable Part Number: 68066095AE
$41.68 MSRP: $62.05
You Save: $20.37 (33%)
ADD TO CART
Product Specifications
- Other Name: Cable - Parking Brake; Brake Cable; Cable Parking Brake
- Replaces: 68066095AC, 68066095AD, 68066095AB, 68066095AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2023 Dodge Challenger | GT, SXT | 3.6L V6, 6 Cyl 3.6 L GAS
View related parts
Dodge Challenger Rear Cable Part Number: 68066189AF
$43.14 MSRP: $64.20
You Save: $21.06 (33%)
ADD TO CART
Product Specifications
- Other Name: Cable - Parking Brake; Brake Cable; Cable Parking Brake
- Replaces: 68066189AD, 68066189AC, 68066189AB, 68066189AE, 68066189AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2023 Dodge Challenger | 392 Hemi Scat Pack Shaker, GT, R/T, R/T 392, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, R/T Shaker, Rallye Redline, SE, SRT 392, SRT Demon, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock, SRT8, SXT, SXT Plus, Scat Pack, T/A, T/A 392, T/A 392 Widebody | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Front Cable Part Number: 4779591AC
Product Specifications
- Other Name: Cable - Parking Brake; Brake Cable; Cable Parking Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Dodge Challenger | R/T, SE, SRT8 | 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Challenger Rear Cable Part Number: 4779322AH
$44.60 MSRP: $64.40
You Save: $19.80 (31%)
Product Specifications
- Other Name: Cable - Parking Brake; Brake Cable; Front Cable; Cable Parking Brake
- Replaces: 4779322AG, 4779322AC, 4779322AF, 4779322AB, 4779322AE, 4779322AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2023 Dodge Challenger | GT, SXT | 3.6L V6, 6 Cyl 3.6 L GAS
View related parts
Dodge Challenger Front Cable Part Number: 4779560AB
Product Specifications
- Other Name: Cable - Parking Brake; Brake Cable; Cable Parking Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Challenger | SRT8 | 8 Cyl 6.1 L GAS

Dodge Challenger Parking Brake Cable

Choose OEM Parking Brake Cable that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Parking Brake Cable follows strict manufacturing steps to lock in quality and fit. If your Dodge Challenger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Challenger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Dodge Challenger Parking Brake Cable is crucial vehicle element that proves our devotion and focus on quality of the Dodge Challenger line. This critical part anchors the parking brake to the normal braking systems to ensure your Dodge Challenger does not roll when parked especially when on an incline. The Parking Brake Cable also improves the performance and Durability which is useful for all challenger models thus it is so important. This Parking Brake Cable serves for different vehicles regardless the models; be it the classic first generation Dodge Challenger or the new generation cars every driver will admire the efficiency of this Parking Brake Cable. The importance of this model, namely the Parking Brake Cable, is quite tangible because it serves as the primary means of preventing accidents and offers a feeling of confident parking. Some of the signs that may indicate that parking brake cable either has faults or is not in good condition include a loose parking brake or even if the warning light is on, thus the need for one to service the vehicle frequently. Therefore, the primary competitive advantage of the Dodge Challenger Parking Brake Cable in the automotive market is its high-quality components made to endure daily use while offering the characteristic power of the Dodge automobiles. In conclusion, Parking Brake Cable is not simply a part of the car but embodies and represents the brand's history and key values; thus, the Dod Chase Challenger Parking Brake Cable remains an essential part of the Dod Chase Challenger.

Dodge Challenger Parking Brake Cable Parts and Q&A

Front Cable
4779591AC
Q: How to Service and Repair a Parking Brake Cable for Front on Dodge Challenger?
A:
Service the front parking brake cable by first lifting and supporting the vehicle. You sometimes need to lock out the parking brake lever, since the lever has only a short travel and tends to stay up because of low tension. Untie the cable under the front parking brake (5) from the connector (3) linked to the rear cable (4) above the axle. Detach the front cable (3) from the equalizer (2), then remove screw (2) securing the cable (1) routing bracket to the rear crossmember front flange (3). After that, unfasten the nuts (1), bolt (2) and push-pins (4) holding the lower rear wheelhouse shield (3) to the vehicle body and remove the shield afterward. Unscrew the screw (6) and remove the routing clip (4) nuts from cable (7) under the body (3) before you lower the vehicle. Get rid of the driver door opening sill scuff plate and cowl side trim and pull the carpet at the front to reach the cable. The cable at the lever should not be taken off from the parking brake connector unless it is secured, because it might end up inside the housing. Pull downward on the connector with the pliers and secure it in the parking brake lever bracket's retaining fork. Lift the front parking brake cable strand (1) off the cable connector (2) which is kept in place by the retaining fork. Grasp the cable retainer at the lever bracket with a 13 mm 12-point box wrench (2) and rotate again to collapse the fingers. While the fingers are collapsed, pull the cable from the bracket. Then, unclip the parking brake cable grommet (2) from the floor pan (3) and remove the parking brake cable (7) through the hole from under the vehicle.
Rear Cable
5290824AB
Q: How to Install a Parking Brake Cable for the Rear on Dodge Challenger?
A:
Route the leading part of the rear parking brake cable up through the cable guide on the crossmember, pass it through the crossmember bracket by the equalizer and press the retainer into the bracket to secure the cable. Take the cable end without the spring and guide it through the rear knuckle (3). Use the supplied handle and tighten the screw firmly so that the torque indicator reads 8 Nm (71 in. lbs.). Fit the parking brake cable end with the actuator lever (1), so that word UP is facing outside and put in the Parking Brake Shoes as well as the necessary supporting components. This service on the parking brake can be done without having to lock out the parking brake lever, thanks to the car's short travel and weak springs. Attach the rear parking brake cable at the equalizer/front cable by linking the left cable (1) at the equalizer (2) above the rear axle differential and rear crossmember (6) or by linking the right cable (4) at connector (3) above the rear axle differential and rear crossmember (6). Wheels just above the floor-yes, that's the spot-parking brake up, press it, lower it and press again. Apply the lever to check if the rear wheels can move freely and after releasing the lever, see if the rotation of the rear wheels is unhassled. Adjust the parking brake shoes as needed and lower the vehicle after that.