How to Install an ABS Control Module Correctly on Dodge Charger?

The first step in installing the Electronic Brake Control Module is to clean anything stuck to the links between the HCU and ABM. Never use lubricants when fitting new O-rings or solenoid valve stem seals. Should the solenoid valve seals be old, take the chance to replace them altogether, as reusing them could open the way for moisture and debris; never reuse old seals. If the pump/motor connector O-ring isn't new, change it and place it in the mounting groove properly. Connect the components and set the ABM onto the HCU, then attach the four screws and tighten them with a torque of 2 Nm (17 in. lbs). Slide the ICU up to the mounting grommets found in the body side rail and gently press the ICU bracket. Clamp the rear brake tubes beneath the Fuse And Relay Center and clip the right front brake tubes to the routing clip on that same bracket. Clip the brake tubes into the two guides that are fixed to the upper radiator support. Remember to install the seal inside the ABM harness connector before fitting it to the ABM. Slide the ABM harness connector into the socket of the ABM and close the cover to secure it. Finally, attach the negative cable from the battery to the battery post and ensure it's done right. Perform the Diagnostic Verification Test to erase any faults from the computer.

How to Remove the ABS Control Module on Dodge Charger?

Start by taking off the negative cable from the battery post and set it aside to remove the Electronic Brake Control Module. After that, unplug the 47-Way wiring connector from the ABM. Take off the brake tubes from their clips along the radiator support and remove the brake tube from its clip under the Fuse And Relay Center. With the assembly off the mounting grommets, slide it just inside so you can access the attaching screws for the ABM. Slide off the equipment behind the HCU after removing the three screws holding the ABM to it.

OEM Dodge Charger ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

35 ABS Control Modules found

View related parts
Dodge Charger Control Module Part Number: 68341606AC
$274.19 MSRP: $407.00
You Save: $132.81 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module Anti-Lock Brake System
- Replaces: 68341606AB, 68341606AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2018 Dodge Charger | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SXT, SXT Plus, SXT Plus Leather | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Modulator Valve Part Number: 68258644AA
$459.68 MSRP: $698.00
You Save: $238.32 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - Anti-Lock Brake; ABS Control Module; ABS Control Unit; Modulator; Hydraulic Control Unit Anti-Lock Brake System; Control Unit Anti-Lock Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2023 Dodge Charger | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SXT, SXT Plus, SXT Plus Leather, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Control Module Part Number: 68028991AA
$502.66 MSRP: $737.00
You Save: $234.34 (32%)
ADD TO CART
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Control Module Part Number: 68291563AA
$331.97 MSRP: $489.00
You Save: $157.03 (33%)
ADD TO CART
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; ABS Control Unit; Module Anti-Lock Brake System
- Replaces: 68266996AA, 68258645AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2016 Dodge Charger | Pursuit, R/T, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SXT | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Control Module Part Number: 68297830AB
$346.97 MSRP: $527.00
You Save: $180.03 (35%)
ADD TO CART
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module Anti-Lock Brake System
- Replaces: 68297830AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2016 Dodge Charger | Pursuit, R/T, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SXT | 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Control Module Part Number: 68003539AB
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Dodge Charger | Base, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Control Module Part Number: 68237098AA
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module; Module Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Control Module Part Number: 68048305AC
$467.16 MSRP: $685.00
You Save: $217.84 (32%)
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module Anti-Lock Brake System
- Replaces: 68048305AA, 68048305AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT | 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Modulator Valve Part Number: 68028990AA
Product Specifications
- Other Name: Control - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Modulator; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Modulator Part Number: 68002339AA
Product Specifications
- Other Name: Control - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Dodge Charger | Base, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Control Module Part Number: 5134111AA
Product Specifications
- Other Name: Master Cylinder - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Modulator Valve; Modulator; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Control Module Part Number: 5159192AC
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Modulator; Module Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Control Module Part Number: 68137007AA
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module; Module Anti-Lock Brake System
- Replaces: 68089527AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011 Dodge Charger | Pursuit, R/T, SE | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Charger Control Module Part Number: 68002341AB
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module
- Replaces: 68002341AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Dodge Charger | Base, Pursuit, R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Modulator Part Number: 68004546AA
Product Specifications
- Other Name: Master Cylinder - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Hydraulic Control Unit Anti-Lock Brake System
- Replaces: 5175605AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Charger | Base, Pursuit, R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Control Module Part Number: 5191296AA
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Modulator Valve; ABS Control Module; Modulator; Module Anti-Lock Brake System
- Replaces: 5159193AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Control Module Part Number: 68210119AB
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module; Module Anti-Lock Brake System
- Replaces: 68210119AA, 68195727AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2014 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Modulator Valve Part Number: 68048306AA
Product Specifications
- Other Name: Control - Anti-Lock Brake System; ABS Hydraulic Assembly; ABS Modulator Valve; ABS Control Module; Modulator; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Control Module Part Number: 68089525AA
Product Specifications
- Other Name: Master Cylinder - Anti-Lock Brake System; ABS Hydraulic Assembly; ABS Modulator Valve; ABS Control Module; Modulator Valve; Modulator; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT, SXT Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Control Module Part Number: 68160269AB
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; Module; Module Anti-Lock Brake System
- Replaces: 68154644AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT, SXT Plus | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS

| Page 1 of 2 |Next >

1-20 of 35 Results

Dodge Charger ABS Control Module

Choose OEM ABS Control Module that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each ABS Control Module follows strict manufacturing steps to lock in quality and fit. If your Dodge Charger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Charger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Dod Charger ABS Control Module is a very vital part that serves as a reminder of the dint made by Dodge Charger car in performance and reliability. This module is used in the antilock braking system (ABS) to avoid wheel lock while stopping and which has greatly enhanced the safety of the vehicles. The Dodge Charger ABS Control Module hence promotes a consistent tractive force needed to maintain a strong contact with the roads; this goes a long way in enhancing the device's control, particularly when driving under difficult conditions. This module is compatible with multiple Charger models and is connected with the vehicle brake system, a group of elements as wheel speed sensors, valves, and pump that must function correctly to adjust the brake pressure. Some other things could also be included in the features of Dodge Charger ABS Control Module such as the electronic stability control (ESC) and the traction control making the Charger even safer and more efficient. This concentration on rendering and security has made the dimitri Dodge charger illustrious in the automotive industrialize, thereby turning it into the/top-grade vehicle for those who are hunting for powerful and trusty vehicles to drive. Dodge Charger ABS Control Module does not only improve the braking system but also plays a vital role to the performance of the car making the Charger continue as a tough competitor for other cars in its segment. Altogether, the Dodge Charger ABS Control Module is a perfect example of an auto part that combines state-of-the-street technologies and rock-like sturdiness, which is recognizable in the Dodge brand's devotion to quality.

Dodge Charger ABS Control Module Parts and Q&A

Control Module
68028991AA
Q: How to Install an ABS Control Module Correctly on Dodge Charger?
A:
The first step in installing the Electronic Brake Control Module is to clean anything stuck to the links between the HCU and ABM. Never use lubricants when fitting new O-rings or solenoid Valve Stem Seals. Should the solenoid valve seals be old, take the chance to replace them altogether, as reusing them could open the way for moisture and debris; never reuse old seals. If the pump/motor connector O-ring isn't new, change it and place it in the mounting groove properly. Connect the components and set the ABM onto the HCU, then attach the four screws and tighten them with a torque of 2 Nm (17 in. lbs). Slide the ICU up to the mounting grommets found in the body side rail and gently press the ICU bracket. Clamp the rear brake tubes beneath the Fuse And Relay Center and clip the right front brake tubes to the routing clip on that same bracket. Clip the brake tubes into the two guides that are fixed to the upper Radiator Support. Remember to install the seal inside the ABM harness connector before fitting it to the ABM. Slide the ABM harness connector into the socket of the ABM and close the cover to secure it. Finally, attach the negative cable from the battery to the battery post and ensure it's done right. Perform the Diagnostic Verification Test to erase any faults from the computer.
Modulator
68002339AA
Q: How to Remove the ABS Control Module on Dodge Charger?
A:
Start by taking off the negative cable from the battery post and set it aside to remove the Electronic Brake Control Module. After that, unplug the 47-Way wiring connector from the ABM. Take off the brake tubes from their clips along the Radiator Support and remove the brake tube from its clip under the Fuse And Relay Center. With the assembly off the mounting grommets, slide it just inside so you can access the attaching screws for the ABM. Slide off the equipment behind the HCU after removing the three screws holding the ABM to it.