How to Service the Drive Shaft's Front Propeller on Dodge Ram 2500?

For the front propeller shaft service, rack the transmission and the transfer case into neutral, next place the vehicle on stands and remove the skid plate if it's present. Mark lines at both transfer case and propeller shaft flange yokes, as well as the lines across the propeller and pinion shaft yokes for easy installation reference. Disconnect the bolts connecting the pinion shaft yoke to the universal joint strap and remove the bolts securing the propeller shaft to the transfer case companion flange. Finally, remove the propeller shaft. To install, put the front propeller shaft under the vehicle and have the rear universal joint over the transfer case companion flange and fit the front universal joint onto the axle pinion yoke. Position the marks correctly and loosely put the bolts in place to fasten the universal joint to the transfer case companion flange. Place the front universal joint in line with the axle pinion yoke and screw the bolts in until they reach a torque of 19 Nm (14 ft. lbs.). Ultimately, use a torque wrench to tighten the bolts connecting the universal joint to the transfer case companion flange to 88 Nm (65 ft. lbs.), reinstall the skid plate if you have one, lower the vehicle and see if the problem has been resolved during a road test.

How to Determine the Angle of a Drive Shaft for Both Two-Piece and One-Piece Configurations on Dodge Ram 2500?

For proper measurement of the propeller shaft angle in both designs, first raise the vehicle, support the axles as evenly as you can and let the wheels and shaft rotate. If you have them, take out the universal joint snap rings so the inclinometer base fits flat. Turn the shaft until you can see that the output yoke bearing is facing toward the ground. Whenever you measure, go front to back keeping to the same side of the motor. Carefully attach Inclinometer 7663 to either the yoke bearing cap or pinion flange ring above the shaft. Align the bubble in the sight so it's in the center and record the observed Output Angle (A). Turn the propeller shaft 90 degrees and put the inclinometer on the yoke bearing so it is even with the shaft and sight the bubble in the glass to measure Propeller Shaft Angle (C) at at the front of the shaft. Rotate the propeller shaft by 90 degrees and position the inclinometer on the eventsuboutput data partner bracket such that the bubble is in the middle of the glass at Companion Flange Input Pinion Angle (B). Subtract the smaller figure (C) from the larger (A) to find the Transmission/Transfer Case Output Operating Angle. Proper cancellation of U-Joint angles is less than 1 degree, while operating angles should be less than 3 degrees. Moreover, for double cardan U-Joint, the operating angles must be less than 10 degrees and at least 1/2 of one degree of propeller shaft angle should be continuous.

OEM Dodge Ram 2500 Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

100 Drive Shafts found

View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123390AD
$932.62 MSRP: $1430.00
You Save: $497.38 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear 1-Piece
- Replaces: 52123390AC, 52123390AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Dodge Ram 2500 | Laramie, Power Wagon, SLT, ST, SXT, TRX | 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123117AC
$1110.53 MSRP: $1700.00
You Save: $589.47 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear 1-Piece
- Replaces: 5146475AA, 52123117AA, 52123117AB, 52105809AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2010 Dodge Ram 2500 | 5.7L V8, 5.9L L6, 6.7L L6
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123104AB
$1685.13 MSRP: $2575.00
You Save: $889.87 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 52123104AA, 52853186AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Dodge Ram 2500 | Laramie, SLT, ST, Sport, TRX4 | 5.9L L6, 6 Cyl 5.9 L DIESEL, 6.7L L6
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123220AD
$2082.93 MSRP: $3165.00
You Save: $1082.07 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear 1-Piece
- Replaces: 52123220AA, 52123220AB, 52123152AA, 52123220AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Dodge Ram 2500 | Laramie, SLT, ST, SXT, TRX | 5.7L V8, 5.9L L6, 6 Cyl 6.7 L DIESEL, 6.7L L6
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123021AC
$1036.23 MSRP: $1525.00
You Save: $488.77 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Front
- Replaces: 52123021AB, 52123021AA, 52105990AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2009 Dodge Ram 2500 | Laramie, Power Wagon, SLT, ST, SXT, Sport, TRX4 | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123386AC
$2994.55 MSRP: $4540.00
You Save: $1545.45 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear 2-Piece
- Replaces: 52123386AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Dodge Ram 2500 | Laramie, SLT, ST, SXT, TRX | 6 Cyl 6.7 L DIESEL
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52105871AB
$846.47 MSRP: $1073.05
You Save: $226.58 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2001 Dodge Ram 2500 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123133AA
$47.79 MSRP: $275.00
You Save: $227.21 (83%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear 2-Piece
- Replaces: 52853146AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2008 Dodge Ram 2500 | Laramie, Power Wagon, SLT, ST, SXT, Sport, TRX4 | 5.7L V8, 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123139AC
$668.53 MSRP: $1015.00
You Save: $346.47 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear 2-Piece
- Replaces: 52123139AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Dodge Ram 2500 | Laramie, SLT, ST, SXT, TRX | 6 Cyl 6.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123325AD
$783.45 MSRP: $1205.00
You Save: $421.55 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 52123325AB, 52123325AA, 52123325AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Dodge Ram 2500 | Laramie, Power Wagon, SLT, ST, SXT, TRX | 5.7L V8, 6.7L L6, 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123360AC
$814.39 MSRP: $1235.00
You Save: $420.61 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear 2-Piece
- Replaces: 52123360AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Dodge Ram 2500 | Laramie, Power Wagon, SLT, ST, SXT, TRX | 6 Cyl 6.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123364AC
$961.35 MSRP: $1475.00
You Save: $513.65 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear 1-Piece
- Replaces: 52123364AB, 5146489AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Dodge Ram 2500 | Laramie, Power Wagon, SLT, ST, SXT, TRX | 5.7L V8, 6.7L L6, 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123327AC
$1065.22 MSRP: $1620.00
You Save: $554.78 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 52123327AB, 52123327AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Dodge Ram 2500 | Laramie, Power Wagon, SLT, ST, SXT, TRX | 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123162AC
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear 1-Piece
- Replaces: 52123162AB, 52123162AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Dodge Ram 2500 | Laramie, Power Wagon, SLT, ST, SXT, TRX | 5.9L L6, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52105866AB
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2002 Dodge Ram 2500 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123122AA
Product Specifications
- Other Name: Shaft - Drive; Driveshaft; Shaft Drive Rear 1-Piece
- Replaces: 52853185AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2007 Dodge Ram 2500 | 5.9L L6
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123105AB
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 52123105AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Ram 2500 | Laramie, SLT, ST, Sport, TRX4 | 5.9L L6, 6 Cyl 5.9 L DIESEL
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123100AB
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 52105810AF, 52123100AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2007 Dodge Ram 2500 | Laramie, Power Wagon, SLT, ST, Sport, TRX4 | 5.7L V8, 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123138AC
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 52123138AA, 52123138AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2009 Dodge Ram 2500 | 5.7L V8, 5.9L L6, 6.7L L6
- 2004 Dodge Ram 2500
View related parts
Dodge Ram 2500 Drive Shaft Part Number: 52123110AC
Product Specifications
- Other Name: Shaft - Drive; Driveshaft
- Replaces: 52123110AB, 52105930AC, 52105930AE, 52105930AF, 52105930AD, 52105930AB, 52123110AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2009 Dodge Ram 2500 | Laramie, Power Wagon, SLT, ST, SXT, Sport, TRX4 | 5.7L V8, 5.9L L6, 6.7L L6, 8 Cyl 5.7 L GAS

| Page 1 of 5 |Next >

1-20 of 100 Results

Dodge Ram 2500 Drive Shaft

Choose OEM Drive Shaft that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Drive Shaft follows strict manufacturing steps to lock in quality and fit. If your Dodge Ram 2500 matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Ram 2500 parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Drive Shaft of Dodge Ram 2500 vehicles allows for the passage of torque from the power source which could either be the engine or transmission to the axles, hence facilitating the transmission of power to the drive wheels. This component is a rod-shaped one that works at circuits of monstrous energy of motion, these energy loads require careful grounding, as otherwise it will be noisy and vibrate, indicating a problem. Concerning the usage of Drive Shafts, different generation Dodge Ram 2500 cars are equipped with one-piece, two pieces and slip-in-tube Drive Shafts. Each is designed to support a rather high mechanical load and at the same time to be fairly lightweight. The selection of a Drive Shaft influences performance much depending on the type of the car including four-wheel or all-wheel drive types that require more than one Drive Shaft to smoothly share the power between the front and rear axles if required.

Dodge Ram 2500 Drive Shaft Parts and Q&A

Drive Shaft
52105871AB
Q: How to Service the Drive Shaft's Front Propeller on Dodge Ram 2500?
A:
For the front propeller shaft service, rack the transmission and the transfer case into neutral, next place the vehicle on stands and remove the skid plate if it's present. Mark lines at both transfer case and propeller shaft flange yokes, as well as the lines across the propeller and pinion shaft yokes for easy installation reference. Disconnect the bolts connecting the pinion shaft yoke to the Universal Joint strap and remove the bolts securing the propeller shaft to the transfer case companion flange. Finally, remove the propeller shaft. To install, put the front propeller shaft under the vehicle and have the rear universal joint over the transfer case companion flange and fit the front universal joint onto the axle pinion yoke. Position the marks correctly and loosely put the bolts in place to fasten the universal joint to the transfer case companion flange. Place the front universal joint in line with the axle pinion yoke and screw the bolts in until they reach a torque of 19 Nm (14 ft. lbs.). Ultimately, use a torque wrench to tighten the bolts connecting the universal joint to the transfer case companion flange to 88 Nm (65 ft. lbs.), reinstall the skid plate if you have one, lower the vehicle and see if the problem has been resolved during a road test.
Drive Shaft
52123021AC
Q: How to Determine the Angle of a Drive Shaft for Both Two-Piece and One-Piece Configurations on Dodge Ram 2500?
A:
For proper measurement of the propeller shaft angle in both designs, first raise the vehicle, support the axles as evenly as you can and let the wheels and shaft rotate. If you have them, take out the Universal Joint snap rings so the inclinometer base fits flat. Turn the shaft until you can see that the output yoke bearing is facing toward the ground. Whenever you measure, go front to back keeping to the same side of the motor. Carefully attach Inclinometer 7663 to either the yoke bearing cap or pinion flange ring above the shaft. Align the bubble in the sight so it's in the center and record the observed Output Angle (A). Turn the propeller shaft 90 degrees and put the inclinometer on the yoke bearing so it is even with the shaft and sight the bubble in the glass to measure Propeller Shaft Angle (C) at at the front of the shaft. Rotate the propeller shaft by 90 degrees and position the inclinometer on the eventsuboutput data partner bracket such that the bubble is in the middle of the glass at Companion Flange Input Pinion Angle (B). Subtract the smaller figure (C) from the larger (A) to find the Transmission/Transfer Case Output Operating Angle. Proper cancellation of U-Joint angles is less than 1 degree, while operating angles should be less than 3 degrees. Moreover, for double cardan U-Joint, the operating angles must be less than 10 degrees and at least 1/2 of one degree of propeller shaft angle should be continuous.