Where is the Crankshaft Position Sensor located and How to remove it on Dodge Ram 3500?

The crankshaft position (CKP) sensor is situated at the rear-right side of the engine cylinder block. The sensor is positioned and bolted in place in a machined hole on the engine block. To disconnect the CKP electrical connector at the sensor, first raise the vehicle and then remove the sensor. Then, take out the CKP mounting bolt. Gently twist and detach the sensor from the cylinder block and take it away from the vehicle. Lastly, check the condition of the sensor O-ring.

How to install the Crankshaft Position Sensor on the 5.7L V-8 on Dodge Ram 3500?

In the 5.7L V-8 Crankshaft Position Sensor installation, clean the machined hole in the engine block before installation. Using a small amount of the engine oil, apply some oil on the sensor o-ring then install the sensor into the engine block with a slight rocking action while twisting it. When tightening the mounting bolt, ensure that the sensor is completely flush to the cylinder block. Failure to do so may damage the sensor mounting tang. Fasten the mounting bolt and tighten it to the torque of 28 Nm (21 ft. lbs.). To finish up, connect the electrical connector to the sensor and lower the vehicle.

OEM Dodge Ram 3500 Crankshaft Position Sensor

Engine Crankshaft Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Crankshaft Position Sensors found

View related parts
Dodge Ram 3500 Crankshaft Position Sensor Part Number: 68569185AA
$112.62 MSRP: $171.00
You Save: $58.38 (35%)
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor
- Replaces: 56027870
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2003 Dodge Ram 3500 | Base | 5.9L V8, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View related parts
Dodge Ram 3500 Crankshaft Position Sensor Part Number: 56028815AB
$146.07 MSRP: $220.00
You Save: $73.93 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor Crankshaft Position
- Replaces: 56028815AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Dodge Ram 3500 | Laramie, SLT, Sport, ST | 5.7L V8, 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 3500 Crankshaft Position Sensor Part Number: 5149230AA
$63.33 MSRP: $93.40
You Save: $30.07 (33%)
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor Sensoe; Crankshaft Sensor; Sensor Crankshaft Position
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2009 Dodge Ram 3500 | Laramie, SLT, ST, SXT | 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 3500 Crankshaft Position Sensor Part Number: 68526830AA
$136.87 MSRP: $244.00
You Save: $107.13 (44%)
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft/Camshaft Position; Engine Camshaft & Crankshaft Position Sensor.; Crankshaft Sensor; Camshaft Sensor
- Replaced by: 68526830AB
- Replaces: 5093101AA, 5179099AB, 5179099AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2010 Dodge Ram 3500 | Laramie, SLT, ST, SXT, Sport, TRX4 | 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL
View related parts
Dodge Ram 3500 Crankshaft Position Sensor Part Number: 68407875AA
$138.26 MSRP: $209.00
You Save: $70.74 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor
- Replaces: 5015488AB, 5015488AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2002 Dodge Ram 3500 | Base | 5.9L L6
- 1998 Dodge Ram 3500 | 5.9L L6
View related parts
Dodge Ram 3500 Crankshaft Position Sensor Part Number: 56027871
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor Crankshaft Position
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2002 Dodge Ram 3500 | Base | 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View related parts
Dodge Ram 3500 Crankshaft Position Sensor Part Number: 56027273AB
Product Specifications
- Other Name: Sensor - Crankshaft; Engine Crankshaft Position Sensor; Crankshaft Sensor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1996 Dodge Ram 3500 | Base | 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View related parts
Dodge Ram 3500 Crankshaft Position Sensor Part Number: 56041041
Product Specifications
- Other Name: Sensor - Crankshaft Timing; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1996 Dodge Ram 3500 | Base
View related parts
Dodge Ram 3500 Crankshaft Position Sensor Part Number: 56028373AB
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor Sensoe; Crankshaft Sensor; Sensor Crankshaft Position
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2005 Dodge Ram 3500 | Laramie, SLT, ST | 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 3500 Crankshaft Position Sensor Part Number: 56027864
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor; Sensor Crankshaft Position
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2003 Dodge Ram 3500 | Base, Laramie, SLT, ST | 10 Cyl 8.0 L GAS
View related parts
Dodge Ram 3500 Crankshaft Position Sensor Part Number: 5149009AD
$82.94 MSRP: $125.00
You Save: $42.06 (34%)
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor
- Replaces: 5149009AA, 5149009AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Dodge Ram 3500 | Laramie, SLT, Sport, ST, SXT | 5.7L V8, 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 3500 Crankshaft Position Sensor Part Number: 68407879AA
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor
- Replaces: 56027272
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1996 Dodge Ram 3500 | Base | 5.9L L6, 5.9L V8, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS, 8.0L V10

Dodge Ram 3500 Crankshaft Position Sensor

Choose OEM Crankshaft Position Sensor that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Crankshaft Position Sensor follows strict manufacturing steps to lock in quality and fit. If your Dodge Ram 3500 matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Ram 3500 parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Dodge Ram 3500 Crankshaft Position Sensor Parts and Q&A

Crankshaft Position Sensor
56028815AB
Q:
Where is the Crankshaft Position Sensor located and How to remove it on Dodge Ram 3500?
A:
The crankshaft position (CKP) sensor is situated at the rear-right side of the engine cylinder block. The sensor is positioned and bolted in place in a machined hole on the engine block. To disconnect the CKP electrical connector at the sensor, first raise the vehicle and then remove the sensor. Then, take out the CKP mounting bolt. Gently twist and detach the sensor from the cylinder block and take it away from the vehicle. Lastly, check the condition of the sensor O-ring.
Crankshaft Position Sensor
5149230AA
Q:
How to install the Crankshaft Position Sensor on the 5.7L V-8 on Dodge Ram 3500?
A:
In the 5.7L V-8 Crankshaft Position Sensor installation, clean the machined hole in the engine block before installation. Using a small amount of the engine oil, apply some oil on the sensor o-ring then install the sensor into the engine block with a slight rocking action while twisting it. When tightening the mounting bolt, ensure that the sensor is completely flush to the cylinder block. Failure to do so may damage the sensor mounting tang. Fasten the mounting bolt and tighten it to the torque of 28 Nm (21 ft. lbs.). To finish up, connect the electrical connector to the sensor and lower the vehicle.