How to Install a Power Steering Pump for a 3.5L Engine on Dodge Sprinter 2500?

First of all, install the pulley if it was removed before you install the power steering pump for the 3.5L engine. After that, replace the front and rear pump brackets if they were separated earlier. With a torque wrench, tighten the engine bolts to 21 Nm (15 ft. lbs.). Swap out each O-ring and hose clamp and after that, attach the supply hose to the pump and fasten the clamp. Tighten the high pressure hose to the pump and make sure it has a torque of 38 Nm (28 ft. lbs.). Set up the power steering drive belt and then add the proper power steering fluid. Afterwards, install the mounting screws and link up the electrical cables again.

How to Service and Repair a Power Steering Pump on Dodge Sprinter 2500?

The initial step to servicing or repairing a power steering pump is to take off the belt from the pump. After that, unscrew the washer bottle's mount and disconnect the electric wires so you can move the bottle. Take out as much power steering fluid as you can, after that detach the steering pump hose and the supply hose. Untighten the pulley bolts that connect the power steering pump to the engine and remove the pulley if it's in your way. When everything is tolerant, transfer the front and rear pump brackets as required.

OEM Dodge Sprinter 2500 Power Steering Pump

Power Steering Pump Unit

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Power Steering Pumps found

View related parts
Dodge Sprinter 2500 Power Steering Pump Part Number: 68006168AA
Product Specifications
- Other Name: Pump - Power Steering; Steering Pump, Mech; Pump Power Steering
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Dodge Sprinter 2500 | Base | 6 Cyl 3.5 L GAS
View related parts
Dodge Sprinter 2500 Power Steering Pump Part Number: 68012236AA
Product Specifications
- Other Name: Pump - Power Steering; Pump Power Steering
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Dodge Sprinter 2500 | Base | 6 Cyl 3.0 L DIESEL
View related parts
Dodge Sprinter 2500 Power Steering Pump Part Number: 5119548AA
Product Specifications
- Other Name: Pump - Power Steering
- Replaces: 5103795AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2006 Dodge Sprinter 2500 | Base | 2.7L L5, 5 Cyl 2.7 L DIESEL

Dodge Sprinter 2500 Power Steering Pump

Choose OEM Power Steering Pump that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Power Steering Pump follows strict manufacturing steps to lock in quality and fit. If your Dodge Sprinter 2500 matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Sprinter 2500 parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Dodge Sprinter 2500 Power Steering Pump is an essential part that has a major positive impact on the vehicle's steering - and therefore exploration - capabilities. This Power Steering Pump is well known for its trusted performance and productivity, this great unit efficiently transform the varying energy in the engine to hydraulic power that assist the driver in the Dodge Sprinter 2500 for easy handling especially when compounded in enclosed urban or mere immensely broad highways. Applicable for the Dodge Sprinter 2500 with the 4-door van and the 2-door pickup, it helps support the efficient performance of the automotive through the suppression of the force needed to steer the car. This part of the car is commonly powered by the car's crankshaft and has some relation to a fluid that is stored in a special container and then supplied the steering mechanism with a constant hydraulic pressure. This reliability is important because normal problems such as leakage or noise lower the performance and therefore requires timely repairs. What defines the Dodge Sprinter 2500 in the automotive market is its relatively invulnerable structure and the fine workmanship that goes with the Dodge logo. The Dodge Sprinter 2500 Power Steering Pump is available in many engines and configurations to satisfy the needs of the consumers and give the smooth and precise handling of the vehicle. At the end, the Power Steering Pump reflects a Dodge company's dedication to delivering quality, performance, and satisfaction to its clients.

Dodge Sprinter 2500 Power Steering Pump Parts and Q&A

Power Steering Pump
68012236AA
Q: How to Install a Power Steering Pump for a 3.5L Engine on Dodge Sprinter 2500?
A:
First of all, install the pulley if it was removed before you install the power steering pump for the 3.5L engine. After that, replace the front and rear pump brackets if they were separated earlier. With a torque wrench, tighten the engine bolts to 21 Nm (15 ft. lbs.). Swap out each O-ring and hose clamp and after that, attach the supply hose to the pump and fasten the clamp. Tighten the high pressure hose to the pump and make sure it has a torque of 38 Nm (28 ft. lbs.). Set up the power steering Drive Belt and then add the proper power steering fluid. Afterwards, install the mounting screws and link up the electrical cables again.
Power Steering Pump
68006168AA
Q: How to Service and Repair a Power Steering Pump on Dodge Sprinter 2500?
A:
The initial step to servicing or repairing a power steering pump is to take off the belt from the pump. After that, unscrew the washer bottle's mount and disconnect the electric wires so you can move the bottle. Take out as much power steering fluid as you can, after that detach the steering pump hose and the supply hose. Untighten the pulley bolts that connect the power steering pump to the engine and remove the pulley if it's in your way. When everything is tolerant, transfer the front and rear pump brackets as required.