How to Service a Driveshaft Center Support Bearing on Dodge Sprinter 3500?

First, take out the propeller shaft and mark it for correct installation during reassembling. Open both of the collar clamps and pull apart the propeller shaft. Motivate to remove the snap ring and then use a Bearing Splitter 1130 and Bridge 938 to pull off the driveshaft center support bearing with the splitter behind the thrust washer. To mount, place the driveshaft center support bearing on the propeller shaft with the protective caps and washer, using Installer 9275. Install the snap ring after that and apply universal grease to the propeller shaft spline. Put the rubber boot on the propeller shaft and press the shaft until it firmly joins in the middle, where the markings align. Make sure the rubber seal is fixed properly and add the newly supplied collar clamps before putting on the propeller shaft again.

How to Install a Driveshaft Center Support Bearing on Dodge Sprinter 3500?

When installing the driveshaft center support bearing, press the bearing onto the propeller shaft with your caps and washer using the installer tool 9275. If the driveshaft center support bearing includes a round flange, put a new bolt into the center of the flange and tighten it to 95 Nm (70 ft. lbs.). Then, set the snap-ring into place and grease the propeller shaft spline with a universal grease. Put the rubber boot in place on the propeller shaft first, then bring the propeller shaft halves together till you can see the markings line up correctly. Secure the rubber seal in the correct place and put on the new clamps for the propeller shaft before you install it.

OEM Dodge Sprinter 3500 Driveshaft Center Support Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Driveshaft Center Support Bearings found

View related parts
Dodge Sprinter 3500 Center Bearing Part Number: 68031836AA
$148.42 MSRP: $175.00
You Save: $26.58 (16%)
Product Specifications
- Other Name: Bearing - Drive Shaft; Drive Shaft Center Support Bearing; Driveshaft Center Support Bearing; Center Bearing Drive Shaft
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2009 Dodge Sprinter 3500 | Base | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.5 L GAS
View related parts
Dodge Sprinter 3500 Center Bearing Part Number: 5104574AA
Product Specifications
- Other Name: Bearing - Drive Shaft; Drive Shaft Center Support Bearing; Driveshaft Center Support Bearing; Center Support Bearing; Center Bearing Drive Shaft
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2006 Dodge Sprinter 3500 | Base | 5 Cyl 2.7 L DIESEL
View related parts
Dodge Sprinter 3500 Center Bearing Part Number: 68031835AA
Product Specifications
- Other Name: Bearing - Drive Shaft; Driveshaft Center Support Bearing
- Replaces: 68006649AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2009 Dodge Sprinter 3500 | Base | 3.0L V6, 3.5L V6, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.5 L GAS

Dodge Sprinter 3500 Driveshaft Center Support Bearing

Choose OEM Driveshaft Center Support Bearing that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Driveshaft Center Support Bearing follows strict manufacturing steps to lock in quality and fit. If your Dodge Sprinter 3500 matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Sprinter 3500 parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

A vital component of the Dodge Sprinter 3500 Driveshaft Center Support Bearing ensures transmission power reaches the rear axle with reliability and performs as expected for driveshaft power transfer. The Driveshaft Center Support Bearing attaches to the front piece of a two-piece driveshaft which enables pivoting activities and suspension movement and reduces vibration levels significantly. The Driveshaft Center Support Bearing has universal application for Dodge Sprinter 3500 vehicles produced between 2003 and 2009 which simultaneously improves driving performance and safety. Driveshaft flexibility increases through the employment of U-Joints together with double cardan joints alongside Rzeppa-type constant velocity joints that enable all-wheel and four-wheel drive capacity. Correct maintenance requires attention because wear and insufficient lubrication in the Driveshaft Center Support Bearing generate noise and vibration which increases at higher speeds. The Dodge Sprinter 3500, with its impressive fuel efficiency of approximately 25 mpg and a towing capacity of 5,000 pounds, benefits greatly from the reliability of the Driveshaft Center Support Bearing. The Dodge Sprinter 3500 Driveshaft Center Support Bearing stands out as an essential automotive component with strong design and wide body compatibility which allows the vehicle to perform optimally.

Dodge Sprinter 3500 Driveshaft Center Support Bearing Parts and Q&A

Center Bearing
5104574AA
Q: How to Service a Driveshaft Center Support Bearing on Dodge Sprinter 3500?
A:
First, take out the propeller shaft and mark it for correct installation during reassembling. Open both of the collar clamps and pull apart the propeller shaft. Motivate to remove the snap ring and then use a Bearing Splitter 1130 and Bridge 938 to pull off the driveshaft center support bearing with the splitter behind the thrust washer. To mount, place the driveshaft center support bearing on the propeller shaft with the protective caps and washer, using Installer 9275. Install the snap ring after that and apply universal grease to the propeller shaft spline. Put the rubber boot on the propeller shaft and press the shaft until it firmly joins in the middle, where the markings align. Make sure the rubber seal is fixed properly and add the newly supplied collar clamps before putting on the propeller shaft again.
Center Bearing
68031835AA
Q: How to Install a Driveshaft Center Support Bearing on Dodge Sprinter 3500?
A:
When installing the driveshaft center support bearing, press the bearing onto the propeller shaft with your caps and washer using the installer tool 9275. If the driveshaft center support bearing includes a round flange, put a new bolt into the center of the flange and tighten it to 95 Nm (70 ft. lbs.). Then, set the snap-ring into place and grease the propeller shaft spline with a universal grease. Put the rubber boot in place on the propeller shaft first, then bring the propeller shaft halves together till you can see the markings line up correctly. Secure the rubber seal in the correct place and put on the new clamps for the propeller shaft before you install it.