How to Remove and Install an Engine Mount on 2000 Jeep Cherokee?

The rear engine mount is a rubber bushing that allows the transmission to sit between the transmission extension housing and the rear support member. Before you take out the rear mount, disconnect the negative cable from your battery, then hoist and hold up the transmission. Remove all the nuts that connect the support cushion to the crossmember and get rid of the crossmember. When using a manual transmission, remove the cushion nuts as well as the cushion and take out the bracket bolts if you have to. If you're doing this procedure using an automatic transmission, loosen and remove the bolts connecting the support cushion and the transmission support bracket from the frame and if the vehicle is 2WD, release and remove the adapter bracket from the transmission and frame as well. Should the transmission support bracket be missing, fit it against the transmission and tighten its bolts to 43 Nm (32 ft. lbs.). Then, fix the cushion support onto the transmission support bracket and add the nuts, tightening them with 46 Nm (34 ft. lbs. torque). For automatic transmission, if the original bracket for the adapter was taken off, mount it back onto the transmission and screw the bolts on until you reach 75 Nm (55 ft. lbs. torque). After that, place the transmission support bracket and support cushion on the transmission, add the bolts and tighten them until you reach 75 Nm (55 ft. lbs.) torque. Second to last, lay the crossmember onto the studs on the cushion and install its nuts, tightening them to 22 Nm (192 in. lbs.). Last, install the crossmember to the sill bolts and turn them to 41 Nm (30 ft. lbs.). Take the transmission support out, lower the car and attach the negative cable to the battery again.

OEM 2000 Jeep Cherokee Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Engine Mounts found

View related parts
2000 Jeep Cherokee Cushion Part Number: 52059347AB
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount Torque Strut; Insulator Engine Mount
- Item Weight: 5.60 Pounds
- Item Dimensions: 10.2 x 10.5 x 10.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52059347AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Cherokee Submodels:
- Classic, Limited, SE, Sport | 6 Cyl 4.0 L GAS
View related parts
2000 Jeep Cherokee Front Mount Part Number: 52019278AD
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount; Engine Mount Bracket; Motor Mount; Insulator; Insulator Engine Mount
- Replaces: 52019278AB, 52019278AC
- Item Weight: 2.10 Pounds
- Item Dimensions: 3.4 x 3.8 x 4.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 52019278AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Cherokee Submodels:
- Classic, Country, Limited, SE, Sport | 6 Cyl 4.0 L GAS
View related parts
2000 Jeep Cherokee Motor Mount Part Number: 52019201AC
Product Specifications
- Other Name: Support - Engine Support; Engine Mount Torque Strut; Engine Mount Bracket; Engine Mount; Front Mount; Front Insulator; Cushion; Cushion Engine Support
- Item Weight: 2.00 Pounds
- Item Dimensions: 3.4 x 4.5 x 4.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52019201AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Cherokee Submodels:
- Base, Briarwood, Chief, Classic, Country, Laredo, Limited, Pioneer, SE, Sport | 6 Cyl 4.0 L GAS
View related parts
2000 Jeep Cherokee Motor Mount Part Number: J3242711
Product Specifications
- Other Name: Insulator; Front Mount; Insulator, Right, Engine Support Right, Mount, Engine - Right
- Item Weight: 1.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: J3242711
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2000 Jeep Cherokee Submodels:
- Base, Chief, Laredo, Pioneer, SE, Sport | 4 Cyl 2.5 L GAS
View related parts
2000 Jeep Cherokee Mount Bracket Part Number: 52003005
Product Specifications
- Other Name: Bracket Engine Mount; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Support Bracket; Front Mount; Left Engine Bracket; Front Cushion To Sill.
- Item Weight: 2.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52003005
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2000 Jeep Cherokee Submodels:
- Base, Chief, Laredo, Pioneer, SE, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS
View related parts
2000 Jeep Cherokee Mount Bracket, Driver Side Part Number: 52002607
Product Specifications
- Other Name: Bracket Engine Mount; Engine Mount Bracket, Left; Engine Mount Torque Strut; Motor Mount; Support Bracket; Front Mount; Engine Mount Bracket
- Position: Driver Side
- Item Weight: 6.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52002607
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Cherokee Submodels:
- Base, Briarwood, Chief, Classic, Country, Laredo, Limited, Pioneer, SE, Sport | 6 Cyl 4.0 L GAS
View related parts
2000 Jeep Cherokee Transmission Mount Part Number: 52001180
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Transmission Mount Cushion; Rear Support for Manual Transmission.
- Item Weight: 3.00 Pounds
- Item Dimensions: 9.3 x 5.3 x 3.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52001180
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Cherokee Submodels:
- Base, Chief, Laredo, Limited, Pioneer, SE, Sport | 4 Cyl 2.1 L DIESEL, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
2000 Jeep Cherokee Mount Bracket Part Number: 52019010AC
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Front Support; Front Mount; Front Bracket; Bracket Engine Mount
- Item Weight: 2.70 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52019010AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2000 Jeep Cherokee Submodels:
- Base, Briarwood, Classic, Country, Laredo, Limited, SE, Sport | 6 Cyl 4.0 L GAS
View related parts
2000 Jeep Cherokee Mount Bracket Part Number: 52002603AD
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Front Support; Front Mount; Front Bracket
- Replaces: 52002603AC
- Item Weight: 3.40 Pounds
- Item Dimensions: 9.1 x 10.1 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52002603AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Cherokee Submodels:
- Base, Briarwood, Chief, Classic, Country, Laredo, Limited, Pioneer, SE, Sport | 4.0L V6, 6 Cyl 4.0 L GAS
View related parts
2000 Jeep Cherokee Mount Bracket Part Number: 52018450AB
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Front Bracket; Bracket Engine Mount
- Item Weight: 7.50 Pounds
- Item Dimensions: 5.9 x 6.9 x 5.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52018450AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Cherokee Submodels:
- SE | 4 Cyl 2.5 L GAS
View related parts
2000 Jeep Cherokee Front Mount Part Number: 52019276AD
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount; Engine Mount Bracket; Motor Mount; Mount; Insulator; Insulator Engine Mount
- Replaces: 52019276AC
- Item Weight: 2.10 Pounds
- Item Dimensions: 4.8 x 4.6 x 3.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 52019276AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Cherokee Submodels:
- SE | 4 Cyl 2.5 L GAS
View related parts
2000 Jeep Cherokee Mount Bracket Part Number: 52058877AB
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Front Bracket; Bracket Engine Mount
- Item Weight: 9.00 Pounds
- Item Dimensions: 8.3 x 6.6 x 4.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52058877AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Cherokee Submodels:
- SE | 4 Cyl 2.5 L GAS
View related parts
2000 Jeep Cherokee Mount Bracket, Passenger Side Part Number: 52020270AB
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Right; Engine Mount Torque Strut; Motor Mount; Support Bracket; Front Mount; Front Bracket; Bracket Engine Mount; Engine Mount Bracket
- Position: Passenger Side
- Item Weight: 4.00 Pounds
- Item Dimensions: 6.6 x 4.5 x 4.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52020270AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Cherokee Submodels:
- Base, Briarwood, Chief, Classic, Country, Laredo, Limited, Pioneer, SE, Sport | 6 Cyl 4.0 L GAS
View related parts
2000 Jeep Cherokee Mount Bracket Part Number: 52020219AB
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Support Bracket; Front Bracket; Bracket Engine Mount
- Item Weight: 5.00 Pounds
- Item Dimensions: 10.9 x 9.4 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52020219AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Cherokee Submodels:
- SE | 4 Cyl 2.5 L GAS

2000 Jeep Cherokee Engine Mount Parts and Q&A

Q: How to Remove and Install an Engine Mount on 2000 Jeep Cherokee?
A: The rear engine mount is a rubber bushing that allows the transmission to sit between the transmission extension housing and the rear support member. Before you take out the rear mount, disconnect the negative cable from your battery, then hoist and hold up the transmission. Remove all the nuts that connect the support cushion to the crossmember and get rid of the crossmember. When using a manual transmission, remove the cushion nuts as well as the cushion and take out the bracket bolts if you have to. If you're doing this procedure using an automatic transmission, loosen and remove the bolts connecting the support cushion and the transmission support bracket from the frame and if the vehicle is 2WD, release and remove the adapter bracket from the transmission and frame as well. Should the transmission support bracket be missing, fit it against the transmission and tighten its bolts to 43 Nm (32 ft. lbs.). Then, fix the cushion support onto the transmission support bracket and add the nuts, tightening them with 46 Nm (34 ft. lbs. torque). For automatic transmission, if the original bracket for the adapter was taken off, mount it back onto the transmission and screw the bolts on until you reach 75 Nm (55 ft. lbs. torque). After that, place the transmission support bracket and support cushion on the transmission, add the bolts and tighten them until you reach 75 Nm (55 ft. lbs.) torque. Second to last, lay the crossmember onto the studs on the cushion and install its nuts, tightening them to 22 Nm (192 in. lbs.). Last, install the crossmember to the sill bolts and turn them to 41 Nm (30 ft. lbs.). Take the transmission support out, lower the car and attach the negative cable to the battery again.