How to Remove and Install Front Engine Mounts on Jeep Cherokee?

Each side of the engine is supported by a rubber-made front engine mount. Start by removing the negative terminal from the battery, lifting up the vehicle and placing some support under the engine to get them out. Then, get rid of the through bolt nut, making sure the through bolt remains and proceed to remove the retaining bolts and nuts from the support cushions, after which you remove both the through bolt and the support cushions. Should the engine support bracket be missing, place the Left and Right brackets on the cylinder block and tighten the stud nuts and bolts on the Right Side to 61 Nm (45 ft. lbs.) and 46 Nm (34 ft. lbs., respectively) and 61 Nm (45 ft. lbs.) on the Left Side bolts. As long as the support cushion brackets have been removed, hold them to the lower front sill and attach the bolts, tightening all the bolts to 54 Nm (40 ft. lbs.) and all the stud nuts to 41 Nm (30 ft. lbs.). Set the support cushions onto the support cushion brackets and use a torque wrench to fasten the right cushion nuts to 65 Nm (48 ft. lbs.) and tighten the left cushion bolt and nuts to 41 Nm (30 ft. lbs.). In the end, fit the through bolt and retaining nut and set the through bolt nut's tightness to 65 Nm (48 ft. lbs.). Take out the engine support, settle the car onto the floor and attach the battery negative cable again.

How to Service and Repair a Front Engine Mount on Jeep Cherokee?

Start the service of the front engine mount by disconnecting the negative cable from the car battery, then raise the vehicle to keep the engine elevated. Pull off the nut from the through bolt, but keep the bolt in place, then remove the bolts and nuts from the support cushions and after that, remove the through bolt and support cushions. When installing, if the engine support bracket is missing, install it onto the block and tighten the bolts to 61 Nm (45 ft. lbs.). Should the support cushion bracket be missing, put it on the lower front sill, put in the bolts and nuts and tighten them to the required torque. Fasten the support cushion with the bracket and tighten the bolts and nuts to 41 Nm (30 ft. lbs.) force. Assemble the through bolt and retaining nut, then tighten the nut to 65 Nm (48 ft. lbs.). Once you're done with the other steps, disconnect the engine support, bring the vehicle back down and attach the negative cable to the battery.

OEM Jeep Cherokee Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

29 Engine Mounts found

View related parts
Jeep Cherokee Link Part Number: 68384495AB
$41.01 MSRP: $59.10
You Save: $18.09 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mount; Bracket Engine Mount Torque Strut; Bracket Engine Mount
- Replaces: 68384495AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2019-2022 Jeep Cherokee | 80th Anniversary, Altitude, High Altitude, Latitude Lux, Latitude Plus, Limited, Overland, Trailhawk, Trailhawk Elite | 4 Cyl 2.0 L GAS
View related parts
Jeep Cherokee Upper Bracket Part Number: 68184357AC
$53.36 MSRP: $76.90
You Save: $23.54 (31%)
Product Specifications
- Other Name: Bracket - Torque Strut; Automatic Transmission Mount Bracket, Upper; Bracket; Bracket Torque Strut
- Position: Upper
- Replaces: 68184357AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2018 Jeep Cherokee | 75th Anniversary, Latitude, Latitude Plus, Limited, Overland, Sport, Trailhawk | 2.4L L4, 3.2L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
View related parts
Jeep Cherokee Front Mount Part Number: 52019278AD
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount; Engine Mount Bracket; Motor Mount; Insulator; Insulator Engine Mount
- Replaces: 52019278AB, 52019278AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2000 Jeep Cherokee | Classic, Country, Limited, SE, Sport | 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Cushion Part Number: 52059347AB
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount Torque Strut; Insulator Engine Mount
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Jeep Cherokee | Classic, Limited, SE, Sport | 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Motor Mount Part Number: 52019201AC
Product Specifications
- Other Name: Support - Engine Support; Engine Mount Torque Strut; Engine Mount Bracket; Engine Mount; Front Mount; Front Insulator; Cushion; Cushion Engine Support
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-2001 Jeep Cherokee | Base, Briarwood, Chief, Classic, Country, Laredo, Limited, Pioneer, SE, Sport | 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Motor Mount, Front Part Number: 52000141
Product Specifications
- Other Name: Cushion Front Support; Front Mount; Mount, Engine
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-1986 Jeep Cherokee | Base, Chief, Laredo, Pioneer | 6 Cyl 2.8 L GAS
View related parts
Jeep Cherokee Mount Bracket Part Number: 52019010AC
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Front Support; Front Mount; Front Bracket; Bracket Engine Mount
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1991-2001 Jeep Cherokee | Base, Briarwood, Classic, Country, Laredo, Limited, SE, Sport | 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Motor Mount, Front Passenger Side Part Number: 52000074
Product Specifications
- Other Name: Engine Engine Front Cushion (R; Front Mount; Insulator, Left; Engine Mount, Left
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-1990 Jeep Cherokee | Base, Chief, Laredo, Pioneer, Sport | 4 Cyl 2.5 L GAS
View related parts
Jeep Cherokee Transmission Mount Part Number: 52001180
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Transmission Mount Cushion; Rear Support for Manual Transmission.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-2000 Jeep Cherokee | Base, Chief, Laredo, Limited, Pioneer, SE, Sport | 4 Cyl 2.1 L DIESEL, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Mount Bracket, Driver Side Part Number: 52002607
Product Specifications
- Other Name: Bracket Engine Mount; Engine Mount Bracket, Left; Engine Mount Torque Strut; Motor Mount; Support Bracket; Front Mount; Engine Mount Bracket
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-2001 Jeep Cherokee | Base, Briarwood, Chief, Classic, Country, Laredo, Limited, Pioneer, SE, Sport | 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Mount Bracket Part Number: 52003005
Product Specifications
- Other Name: Bracket Engine Mount; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Support Bracket; Front Mount; Left Engine Bracket; Front Cushion To Sill.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-2000 Jeep Cherokee | Base, Chief, Laredo, Pioneer, SE, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS
View related parts
Jeep Cherokee Motor Mount Part Number: J3242711
Product Specifications
- Other Name: Insulator; Front Mount; Insulator, Right, Engine Support Right, Mount, Engine - Right
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-2000, 1984-1990 Jeep Cherokee | Base, Chief, Laredo, Pioneer, SE, Sport | 4 Cyl 2.5 L GAS
View related parts
Jeep Cherokee Cushion Part Number: J3242728
Product Specifications
- Other Name: Insulator - Engine Mount; Insulator, Right, Support Front Cushion; Mount, Engine Support Right; Insulator Engine Mount
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997 Jeep Cherokee | SE | 4 Cyl 2.5 L GAS
View related parts
Jeep Cherokee Mount Bracket Part Number: 52002603AD
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Front Support; Front Mount; Front Bracket
- Replaces: 52002603AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-2001 Jeep Cherokee | Base, Briarwood, Chief, Classic, Country, Laredo, Limited, Pioneer, SE, Sport | 4.0L V6, 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Mount Bracket Part Number: 52018450AB
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Front Bracket; Bracket Engine Mount
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-2000 Jeep Cherokee | SE | 4 Cyl 2.5 L GAS
View related parts
Jeep Cherokee Front Mount Part Number: 52019276AD
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount; Engine Mount Bracket; Motor Mount; Mount; Insulator; Insulator Engine Mount
- Replaces: 52019276AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2000 Jeep Cherokee | SE | 4 Cyl 2.5 L GAS
View related parts
Jeep Cherokee Mount Bracket Part Number: 52058877AB
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Front Bracket; Bracket Engine Mount
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-2000 Jeep Cherokee | SE | 4 Cyl 2.5 L GAS
View related parts
Jeep Cherokee Mount Bracket, Passenger Side Part Number: 52020270AB
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Right; Engine Mount Torque Strut; Motor Mount; Support Bracket; Front Mount; Front Bracket; Bracket Engine Mount; Engine Mount Bracket
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-2001 Jeep Cherokee | Base, Briarwood, Chief, Classic, Country, Laredo, Limited, Pioneer, SE, Sport | 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Mount Bracket Part Number: 52020219AB
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Support Bracket; Front Bracket; Bracket Engine Mount
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-2000 Jeep Cherokee | SE | 4 Cyl 2.5 L GAS
View related parts
Jeep Cherokee Trans Crossmember Part Number: 52058643AC
Product Specifications
- Other Name: Crossmember - Transmission; Crossmember Transmission
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1996 Jeep Cherokee | SE

| Page 1 of 2 |Next >

1-20 of 29 Results

Jeep Cherokee Engine Mount

Choose OEM Engine Mount that meet Jeep factory standards. Jeep designs and tests every component for precision and durability. Each Engine Mount follows strict manufacturing steps to lock in quality and fit. If your Jeep Cherokee matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Cherokee parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Engine Mount in Jeep Cherokee vehicles serves two primary functions: It has the function of noise and vibration absorbing from the engine and has a role of supporting and locating of the engine & transaxle within the car's chassis. One of these is isolation for enhancing comfort and the other is correct positioning of the engine for safety and to avoid straining of parts. The Engine Mounts used in Jeep Cherokee have been the regular rubber ones, fluid filled hydraulic ones and the recently developed sophisticated electronic active Engine Mounts. Conventional rides have metal parts which are separated by rubber spacers while hydraulic types have more damping capability. The new active mounts are variable which precisely alter the firmness in performance depending on the engine RPM. Engine Mounts can get worn out through time, heat etc, this can lead to noise and vibration thus warranting inspection and or replacement.

Jeep Cherokee Engine Mount Parts and Q&A

Cushion
52059347AB
Q: How to Remove and Install Front Engine Mounts on Jeep Cherokee?
A:
Each side of the engine is supported by a rubber-made front engine mount. Start by removing the negative terminal from the battery, lifting up the vehicle and placing some support under the engine to get them out. Then, get rid of the through bolt nut, making sure the through bolt remains and proceed to remove the retaining bolts and nuts from the support cushions, after which you remove both the through bolt and the support cushions. Should the engine support bracket be missing, place the Left and Right brackets on the cylinder block and tighten the stud nuts and bolts on the Right Side to 61 Nm (45 ft. lbs.) and 46 Nm (34 ft. lbs., respectively) and 61 Nm (45 ft. lbs.) on the Left Side bolts. As long as the support cushion brackets have been removed, hold them to the lower front sill and attach the bolts, tightening all the bolts to 54 Nm (40 ft. lbs.) and all the stud nuts to 41 Nm (30 ft. lbs.). Set the support cushions onto the support cushion brackets and use a torque wrench to fasten the right cushion nuts to 65 Nm (48 ft. lbs.) and tighten the left cushion bolt and nuts to 41 Nm (30 ft. lbs.). In the end, fit the through bolt and retaining nut and set the through bolt nut's tightness to 65 Nm (48 ft. lbs.). Take out the engine support, settle the car onto the floor and attach the battery negative cable again.
Motor Mount
52019201AC
Q: How to Service and Repair a Front Engine Mount on Jeep Cherokee?
A:
Start the service of the front engine mount by disconnecting the negative cable from the car battery, then raise the vehicle to keep the engine elevated. Pull off the nut from the through bolt, but keep the bolt in place, then remove the bolts and nuts from the support cushions and after that, remove the through bolt and support cushions. When installing, if the engine support bracket is missing, install it onto the block and tighten the bolts to 61 Nm (45 ft. lbs.). Should the support cushion bracket be missing, put it on the lower front sill, put in the bolts and nuts and tighten them to the required torque. Fasten the support cushion with the bracket and tighten the bolts and nuts to 41 Nm (30 ft. lbs.) force. Assemble the through bolt and retaining nut, then tighten the nut to 65 Nm (48 ft. lbs.). Once you're done with the other steps, disconnect the engine support, bring the vehicle back down and attach the negative cable to the battery.