How to Service and Repair a Crankshaft Seal on 2001 Dodge Stratus?

Before doing maintenance on the crankshaft main bearing seal, first remove the transaxle and then take out the drive plate. Slip the shaft of a 3/16" wide flat bladed screwdriver into the area between the crankshaft seal's metal case and the dust lip, not allowing the screwdriver to get in contact with the seal itself, only with the chamfer. If the crankshaft has any uneven marks or scratches, gently sand it with 400 grit sandpaper to stop the seal from splitting during setup. Thereafter, put Special Tool 6926-1 Guide on the crankshaft and position it so that its base magnetically mounts it as a pilot tool. Put the seal over the pilot tool, so the seal's lip is next to the crankshaft and hold the pilot tool firmly during installation. Finish up by using Special Tool 6926-2 Installer and C-4171 Handle to push the seal into the retainer housing so it matches the housing surface, install the drive plate and transaxle again.

OEM 2001 Dodge Stratus Crankshaft Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Crankshaft Seals found

View related parts
2001 Dodge Stratus Front Crank Seal Part Number: 4663618
$20.20 MSRP: $29.95
You Save: $9.75 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Crankshaft Oil; Engine Crankshaft Seal, Front; Engine Timing Cover Seal; Timing Cover Gasket; Timing Cover Seal; Front Seal; Crankshaft Oil Front; Engine Crankshaft Seal.
- Position: Front
- Item Weight: 0.40 Pounds
- Item Dimensions: 0.2 x 2.1 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4663618
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Stratus Submodels:
- ES, R/T, SE, SE Plus, SXT | 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
2001 Dodge Stratus Rear Main Seal Part Number: 4621939AB
$27.24 MSRP: $40.20
You Save: $12.96 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Rear Main Crankshaft; Engine Crankshaft Seal, Rear; Rear Seal; Seal Rear Main Crankshaft Serviced With Retainer [04663625]; Crankshaft Seal
- Position: Rear
- Item Weight: 0.50 Pounds
- Item Dimensions: 0.7 x 4.6 x 4.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4621939AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Stratus Submodels:
- Base, ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
2001 Dodge Stratus Rear Main Seal Part Number: 4663625
$32.82 MSRP: $42.24
You Save: $9.42 (23%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Rear Main Crankshaft; Engine Crankshaft Seal, Rear; Rear Main Seal Gasket; Seal Rear Main Crankshaft See Note; Seal Rear Main Crankshaft
- Position: Rear
- Item Weight: 0.50 Pounds
- Item Dimensions: 4.8 x 4.7 x 0.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4663625
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Stratus Submodels:
- ES, R/T, SE, SE Plus, SXT | 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
2001 Dodge Stratus Rear Main Seal Retainer Part Number: 4663622
Product Specifications
- Other Name: Cover - Crankshaft Rear Oil Seal; Retainer Crankshaft Rear Oil Seal
- Position: Rear
- Item Weight: 0.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4663622
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Stratus Submodels:
- ES, R/T, SE, SE Plus, SXT | 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS

2001 Dodge Stratus Crankshaft Seal Parts and Q&A

Q: How to Service and Repair a Crankshaft Seal on 2001 Dodge Stratus?
A: Before doing maintenance on the crankshaft main bearing seal, first remove the transaxle and then take out the drive plate. Slip the shaft of a 3/16" wide flat bladed screwdriver into the area between the crankshaft seal's metal case and the dust lip, not allowing the screwdriver to get in contact with the seal itself, only with the chamfer. If the crankshaft has any uneven marks or scratches, gently sand it with 400 grit sandpaper to stop the seal from splitting during setup. Thereafter, put Special Tool 6926-1 Guide on the crankshaft and position it so that its base magnetically mounts it as a pilot tool. Put the seal over the pilot tool, so the seal's lip is next to the crankshaft and hold the pilot tool firmly during installation. Finish up by using Special Tool 6926-2 Installer and C-4171 Handle to push the seal into the retainer housing so it matches the housing surface, install the drive plate and transaxle again.