How to Locate and Replace an Oxygen Sensor on 2001 Dodge Stratus?

Each of the O2 sensors is installed at the bottom of the two outlets in the catalytic converter. Be certain to cool the engine before starting the replacement, as the exhaust manifold, exhaust pipes and catalytic converter can heat up and cause injuries. To start, remove the negative battery cable and after that, make sure the car is raised and supported. All you need to do is disconnect the O2 sensor wire connector without pulling directly on the wire within the sensor. The YA 8875 Snap-On oxygen sensor wrench should be used when removing the sensor. Following sensor removal, use an 18 mm X 1.5 + 6E tap to clean the exhaust manifold threads. When keeping your original sensor, apply an anti-seize compound like Loctite 771-64 to its threads; new sensors already come pre-coated, so additional compound is not essential. First screw the sensor to 28 Nm (20 ft. lbs.) torque and then place the O2 sensor and tighten it to the same 28 Nm (20 ft. lbs.). Attach the O2 sensor wire connector, position the vehicle once more and put the negative battery cable back in.

OEM 2001 Dodge Stratus Oxygen Sensor

Oxygen O2 Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Oxygen Sensors found

View related parts
2001 Dodge Stratus Oxygen Sensor, Front Part Number: 4606133AD
$91.13 MSRP: $191.00
You Save: $99.87 (53%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front, Rear; Rear Oxygen Sensor; Front Oxygen Sensor; Sensor Oxygen
- Position: Front
- Item Weight: 0.60 Pounds
- Item Dimensions: 1.3 x 28.5 x 6.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4606133AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Stratus Submodels:
- ES, R/T, SE, SE Plus, SXT | 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
2001 Dodge Stratus Oxygen Sensor, Front Part Number: MD354851
$220.26 MSRP: $279.22
You Save: $58.96 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front Left; Sensor Oxygen
- Position: Front
- Item Weight: 0.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MD354851
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Stratus Submodels:
- R/T, SE | 6 Cyl 3.0 L GAS
View related parts
2001 Dodge Stratus Oxygen Sensor, Front Part Number: 4606555AB
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front; Sensor Oxygen
- Position: Front
- Item Weight: 0.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4606555AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Stratus Submodels:
- ES, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS
View related parts
2001 Dodge Stratus Oxygen Sensor, Rear Part Number: 4606135AD
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Rear; Sensor Oxygen
- Position: Rear
- Item Weight: 0.60 Pounds
- Item Dimensions: 16.3 x 1.0 x 1.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4606135AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Stratus Submodels:
- ES, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS
View related parts
2001 Dodge Stratus Oxygen Sensor, Rear Part Number: MR560365
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Rear; Rear Oxygen Sensor; Sensor Oxygen
- Position: Rear
- Item Weight: 0.70 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR560365
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Stratus Submodels:
- ES, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS
View related parts
2001 Dodge Stratus Oxygen Sensor, Front Part Number: MR560364
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front; Front Oxygen Sensor; Sensor Oxygen
- Position: Front
- Item Weight: 0.60 Pounds
- Item Dimensions: 3.6 x 1.3 x 1.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR560364
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Stratus Submodels:
- ES, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS
View related parts
2001 Dodge Stratus Oxygen Sensor, Front Part Number: MD354850
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front Right; Sensor Oxygen
- Position: Front
- Item Weight: 0.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MD354850
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Stratus Submodels:
- R/T, SE | 6 Cyl 3.0 L GAS
View related parts
2001 Dodge Stratus Oxygen Sensor, Rear Part Number: MD345230
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Rear; Sensor Oxygen
- Position: Rear
- Item Weight: 0.60 Pounds
- Item Dimensions: 6.1 x 7.4 x 1.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: MD345230
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Stratus Submodels:
- R/T, SE | 6 Cyl 3.0 L GAS

2001 Dodge Stratus Oxygen Sensor Parts and Q&A

Q: How to Locate and Replace an Oxygen Sensor on 2001 Dodge Stratus?
A: Each of the O2 sensors is installed at the bottom of the two outlets in the catalytic converter. Be certain to cool the engine before starting the replacement, as the exhaust manifold, exhaust pipes and catalytic converter can heat up and cause injuries. To start, remove the negative battery cable and after that, make sure the car is raised and supported. All you need to do is disconnect the O2 sensor wire connector without pulling directly on the wire within the sensor. The YA 8875 Snap-On oxygen sensor wrench should be used when removing the sensor. Following sensor removal, use an 18 mm X 1.5 + 6E tap to clean the exhaust manifold threads. When keeping your original sensor, apply an anti-seize compound like Loctite 771-64 to its threads; new sensors already come pre-coated, so additional compound is not essential. First screw the sensor to 28 Nm (20 ft. lbs.) torque and then place the O2 sensor and tighten it to the same 28 Nm (20 ft. lbs.). Attach the O2 sensor wire connector, position the vehicle once more and put the negative battery cable back in.