How to Replace the Downstream Oxygen Sensor 1/2 on 2000 Dodge Stratus?

To change the Oxygen Sensor located 1/2 down, open the negative battery cable and lift the car. Remove the electrical connector from the sensor and release the sensor electrical harness from its clips on the body. Take out the sensor with a special wrench called the Snap-On tool YA8875 or an equal model. After removing the exhaust manifold, clear its threads with a 18 mm X 1.5 + 6E tap. Should you choose to reuse the sensor, put anti-seize compound like Loctite (R) 771-64 or its equivalent onto the threads; new sensors are already coated and do not need more. Adjust the sensor so it has a torque of 28 Nm (20 ft. lbs.) Attach the sensor electrical wires to their clips under the vehicle and then attach the electrical connector to the sensor. Set the car down into place and reattach the negative battery cable.

OEM 2000 Dodge Stratus Oxygen Sensor

Oxygen O2 Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Oxygen Sensors found

View related parts
2000 Dodge Stratus Oxygen Sensor, Front Part Number: 4606133AC
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front, Rear; Sensor Oxygen
- Position: Front
- Item Weight: 0.60 Pounds
- Item Dimensions: 4.2 x 1.0 x 1.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4606133AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Dodge Stratus Submodels:
- Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
2000 Dodge Stratus Oxygen Sensor Part Number: 4606135AB
Product Specifications
- Other Name: Sensor - Oxygen; Sensor Oxygen
- Item Weight: 0.90 Pounds
- Item Dimensions: 4.1 x 1.1 x 1.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4606135AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Dodge Stratus Submodels:
- Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
2000 Dodge Stratus Oxygen Sensor Part Number: 4606950AB
Product Specifications
- Other Name: Sensor - Oxygen; Sensor Oxygen
- Item Weight: 1.00 Pounds
- Item Dimensions: 8.3 x 7.5 x 1.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4606950AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Dodge Stratus Submodels:
- ES | 6 Cyl 2.5 L GAS

2000 Dodge Stratus Oxygen Sensor Parts and Q&A

Q: How to Replace the Downstream Oxygen Sensor 1/2 on 2000 Dodge Stratus?
A: To change the Oxygen Sensor located 1/2 down, open the negative battery cable and lift the car. Remove the electrical connector from the sensor and release the sensor electrical harness from its clips on the body. Take out the sensor with a special wrench called the Snap-On tool YA8875 or an equal model. After removing the exhaust manifold, clear its threads with a 18 mm X 1.5 + 6E tap. Should you choose to reuse the sensor, put anti-seize compound like Loctite (R) 771-64 or its equivalent onto the threads; new sensors are already coated and do not need more. Adjust the sensor so it has a torque of 28 Nm (20 ft. lbs.) Attach the sensor electrical wires to their clips under the vehicle and then attach the electrical connector to the sensor. Set the car down into place and reattach the negative battery cable.