JeepParts
My Garage
My Account
Cart
OEM 2004 Chrysler Crossfire Crankshaft Seal
- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
3 Crankshaft Seals found
2004 Chrysler Crossfire Crankshaft Seal, Front Part Number: 5073675AB
$53.33 MSRP: $79.25You Save: $25.92 (33%)Ships in 1-2 Business DaysProduct Specifications- Other Name: Seal - Crankshaft Oil; Engine Crankshaft Seal, Front; Timing Cover Gasket; Timing Cover Seal; Front Crank Seal; Front Seal; Front Cover Seal; Seal Crankshaft Oil Front; Oil Seal; Engine Crankshaft Seal
- Position: Front
- Replaces: 5073675AA, 5073676AA
- Item Weight: 0.50 Pounds
- Item Dimensions: 2.7 x 2.6 x 0.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5073675AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
2004 Chrysler Crossfire Rear Main Seal Part Number: 5099346AB
$27.22 MSRP: $52.05You Save: $24.83 (48%)Ships in 1-2 Business DaysProduct Specifications- Other Name: Seal - Rear Main Crankshaft; Engine Crankshaft Seal; Crankshaft Seal
- Position: Rear
- Item Weight: 0.70 Pounds
- Item Dimensions: 5.5 x 5.4 x 1.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5099346AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
2004 Chrysler Crossfire Retainer, Rear Part Number: 5127283AA
$29.92 MSRP: $34.35You Save: $4.43 (13%)Ships in 1-2 Business DaysProduct Specifications- Other Name: Retainer - Crankshaft Rear Oil Seal; Retainer Crankshaft Rear Oil Seal
- Position: Rear
- Item Weight: 0.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5127283AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
2004 Chrysler Crossfire Crankshaft Seal Parts and Q&A
- Q: How to Service and Repair a Crankshaft Seal on 2004 Chrysler Crossfire?A: You should begin by removing the flywheel and both end cover bolts from the crankshaft, then take off the cover and throw away both the cover and the oil seal. The engine block and oil pan gasket surfaces should be carefully cleaned. Coat the area on the new end cover with a 1.5 mm to 2 mm bead of Loctite 5203 sealer as suggested and set the new end cover without the seal in place, then put in the retaining bolts and tighten them to 10 Nm (89 in. lbs.). Clean the edge of the hole where the rear crankshaft oil seal will mount and check that the oil seal's edge is still intact and unsmashed. The circumference and side lip within the small groove on the rear seal, plus the corresponding surface, should be oil- and grease-free. Set the rear crankshaft oil seal into the new end cover by adding Special Tool 9100 and no more than 1 mm (0.039 in.) between the seal and the edge of the cover in every direction. The last step is to pull out the Special Tool 9100 Rear Seal Installer and set the flywheel back in place.
Related 2004 Chrysler Crossfire Parts
2004 Chrysler Crossfire Cam Gear
2004 Chrysler Crossfire Coolant Filter
2004 Chrysler Crossfire Crankshaft
2004 Chrysler Crossfire Cylinder Head Gasket
2004 Chrysler Crossfire Dipstick
2004 Chrysler Crossfire Drain Plug Washer
2004 Chrysler Crossfire Engine Mount Bracket
2004 Chrysler Crossfire Oil Filler Cap
2004 Chrysler Crossfire Piston Ring Set
2004 Chrysler Crossfire Timing Chain Guide
2004 Chrysler Crossfire Timing Cover
2004 Chrysler Crossfire Transmission Mount