How Should a Crankshaft Seal Be Properly Installed and Replaced on Chrysler Crossfire?

It is not possible to change only the rear crankshaft oil seal; the seal and the end cover are installed as a set by the factory. You have ten minutes from applying sealer to assemble components requiring it. Roll a 1.5 mm to 2 mm long strip of Loctite 5203 sealer on the new end cover. Fit the new end cover, skipping the seal and the retaining bolts, then tighten them to 10 Nm (89 in. lbs.). Keep the whole edge of the hole around the rear crankshaft oil seal free from burrs and check that its sealing lip is not damaged or crushed. It is important that neither the circumference nor the sealing lip of the rear crankshaft oil seal, nor its mating contact surface, are contaminated with oil or grease. Angle the oil seal at the rear of the crankshaft in parallel lines to the crankshaft to maintain a tight seal. After placing the Special Tool 9100 Rear Seal Installer into the new end cover, place the rear crankshaft oil seal and make sure the distance between these two pieces is 1 mm (.039 in.) around the edge. Uninstall Special Tool 9100 Rear Seal Installer and place the flywheel.

How to Remove and Service a Front Crankshaft Seal on Chrysler Crossfire?

Always begin by removing the negative battery cable before undertaking front crankshaft seal service or repair. After that, get rid of the engine cooling fan and its shroud and then remove the accessory drive belt. After that, take off the vibration damper. Protect the crankshaft by pulling out the front crankshaft oil seal (1) using a rag and the right tool.

OEM Chrysler Crossfire Crankshaft Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Crankshaft Seals found

View related parts
Chrysler Crossfire Crankshaft Seal, Front Part Number: 5073675AB
$53.33 MSRP: $79.25
You Save: $25.92 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Crankshaft Oil; Engine Crankshaft Seal, Front; Timing Cover Gasket; Timing Cover Seal; Front Crank Seal; Front Seal; Front Cover Seal; Seal Crankshaft Oil Front; Oil Seal; Engine Crankshaft Seal
- Position: Front
- Replaces: 5073675AA, 5073676AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chrysler Crossfire | Base, Limited, SRT-6 | 6 Cyl 3.2 L GAS
View related parts
Chrysler Crossfire Rear Main Seal Part Number: 5099346AB
$27.22 MSRP: $52.05
You Save: $24.83 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Rear Main Crankshaft; Engine Crankshaft Seal; Crankshaft Seal
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2007 Chrysler Crossfire | Base, Limited, SRT-6 | 6 Cyl 3.2 L GAS
View related parts
Chrysler Crossfire Retainer, Rear Part Number: 5127283AA
$29.92 MSRP: $34.35
You Save: $4.43 (13%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Retainer - Crankshaft Rear Oil Seal; Retainer Crankshaft Rear Oil Seal
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2007 Chrysler Crossfire | Base, Limited, SRT-6 | 6 Cyl 3.2 L GAS

Chrysler Crossfire Crankshaft Seal

Choose OEM Crankshaft Seal that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Crankshaft Seal follows strict manufacturing steps to lock in quality and fit. If your Chrysler Crossfire matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Crossfire parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Chrysler Crossfire Crankshaft Seal is one of the special parts that are very crucial in the success of the Chrysler Crossfire engine. Sput out at the front part of the motor, this Crankshaft Seal helps avoid the seepage of the engine oil from the crankcase thereby maintaining lubrication of critical motor parts. Being made of a strong compound of metal and rubber the Chrysler Crossfire Crankshaft Seal reduces friction and the rate of wear of the car thus increasing the Cars efficiency and durability. The fitment note covers most Chrysler Crossfire line and it guarantees that users will benefit from using this Crankshaft Seal to correct their piece's performance. A faulty Crankshaft Seal causes oil leaks; this not only hampers the efficiency of the vehicle's engines but also is dangerous for the driver. As a result, proper replacement of the Chrysler Crossfire Crankshaft Seal should be done before it compromises the vehicle's performance and safety features. In the aspect of construction, it is exemplary to note that among all the automotive products in the market, Crankshaft Seal boasts of its sturdy and dependable nature, which has made it to be most recommended by Chrysler users. Therefore, the Crankshaft Seal is not just a regular component of the Chrysler Crossfire, as it was introduced previously; but rather it forms a crucial part of the cars assembly that adds value to the efficiency, safety of the cross fire.

Chrysler Crossfire Crankshaft Seal Parts and Q&A

Retainer, Rear
5127283AA
Q: How Should a Crankshaft Seal Be Properly Installed and Replaced on Chrysler Crossfire?
A:
It is not possible to change only the rear crankshaft oil seal; the seal and the end cover are installed as a set by the factory. You have ten minutes from applying sealer to assemble components requiring it. Roll a 1.5 mm to 2 mm long strip of Loctite 5203 sealer on the new end cover. Fit the new end cover, skipping the seal and the retaining bolts, then tighten them to 10 Nm (89 in. lbs.). Keep the whole edge of the hole around the rear crankshaft oil seal free from burrs and check that its sealing lip is not damaged or crushed. It is important that neither the circumference nor the sealing lip of the rear crankshaft oil seal, nor its mating contact surface, are contaminated with oil or grease. Angle the oil seal at the rear of the crankshaft in parallel lines to the crankshaft to maintain a tight seal. After placing the Special Tool 9100 Rear Seal Installer into the new end cover, place the rear crankshaft oil seal and make sure the distance between these two pieces is 1 mm (.039 in.) around the edge. Uninstall Special Tool 9100 Rear Seal Installer and place the Flywheel.
Crankshaft Seal, Front
5073675AB
Q: How to Remove and Service a Front Crankshaft Seal on Chrysler Crossfire?
A:
Always begin by removing the negative battery cable before undertaking front crankshaft seal service or repair. After that, get rid of the engine cooling fan and its shroud and then remove the accessory Drive Belt. After that, take off the vibration damper. Protect the crankshaft by pulling out the front crankshaft oil seal (1) using a rag and the right tool.