How to Service and Repair a Brake Master Cylinder on 2004 Dodge Ram 2500?

Before servicing or repairing the brake master cylinder on any model except Hydroboost, remove the brake lines, disconnect the electrical wire for the low fluid level and undo the mounting nuts to take out the master cylinder. Carefully pull the master cylinder forward so you don't dislodge the output rod in the booster. Make sure to bleed the master cylinder and make sure the brake booster's output rod is placed so that it will go into the master cylinder plunger sleeve when you put the master cylinder in. After removing the booster, pump your foot on the brake pedal a few times to drive out excess vacuum. Then, connect the master cylinder to the booster (tighten new mounting nuts to 25 Nm / 221 in. lbs.), attach the brake lines, put back the switch electrical connector and finally both prime and bleed the entire base brake system.

OEM 2004 Dodge Ram 2500 Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Brake Master Cylinders found

View related parts
2004 Dodge Ram 2500 Master Cylinder Part Number: 5093408AA
Product Specifications
- Other Name: Motor Cylinder - Brake Master Cylinder; Brake Master Cylinder Reservoir; Brake Reservoir; Master Cylinder Reservoir; Reservoir; Reservoir Brake Master Cylinder
- Item Weight: 1.50 Pounds
- Item Dimensions: 8.3 x 6.4 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5093408AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Ram 2500 Submodels:
- Laramie, Power Wagon, SLT, ST, SXT, Sport, TRX, TRX4 | 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
2004 Dodge Ram 2500 Master Cylinder Part Number: 5080888AB
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Item Weight: 5.70 Pounds
- Item Dimensions: 10.1 x 9.7 x 8.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5080888AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Ram 2500 Submodels:
- Laramie, Power Wagon, SLT, ST, SXT, Sport, TRX, TRX4 | 10 Cyl 8.0 L GAS, 6 Cyl 6.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
2004 Dodge Ram 2500 Master Cylinder Part Number: 5093407AA
Product Specifications
- Other Name: Motor Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5093407AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2004 Dodge Ram 2500 Submodels:
- Laramie, SLT, ST | 6 Cyl 5.9 L DIESEL

2004 Dodge Ram 2500 Brake Master Cylinder Parts and Q&A

Q: How to Service and Repair a Brake Master Cylinder on 2004 Dodge Ram 2500?
A: Before servicing or repairing the brake master cylinder on any model except Hydroboost, remove the brake lines, disconnect the electrical wire for the low fluid level and undo the mounting nuts to take out the master cylinder. Carefully pull the master cylinder forward so you don't dislodge the output rod in the booster. Make sure to bleed the master cylinder and make sure the brake booster's output rod is placed so that it will go into the master cylinder plunger sleeve when you put the master cylinder in. After removing the booster, pump your foot on the brake pedal a few times to drive out excess vacuum. Then, connect the master cylinder to the booster (tighten new mounting nuts to 25 Nm / 221 in. lbs.), attach the brake lines, put back the switch electrical connector and finally both prime and bleed the entire base brake system.