JeepParts
My Garage
My Account
Cart
OEM 2005 Dodge Ram 2500 Ball Joint
Control Arm Joint- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
3 Ball Joints found
2005 Dodge Ram 2500 Ball Joints, Front Lower Part Number: 5086674AC
$103.28 MSRP: $229.00You Save: $125.72 (55%)Product Specifications- Other Name: Balljoint - Lower; Suspension Ball Joint, Front Lower; Suspension Ball Joint; Ball Joint; Lower Ball Joint
- Position: Front Lower
- Item Weight: 5.30 Pounds
- Item Dimensions: 3.3 x 4.9 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5086674AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
2005 Dodge Ram 2500 Ball Joints, Front Upper Part Number: 68214646AA
$88.03 MSRP: $124.00You Save: $35.97 (30%)Product Specifications- Other Name: Balljoint - Upper; Suspension Ball Joint, Front Upper; Telescopic Ball Joint; Upper Ball Joint; Upper Ball Joints; Ball Joint Kit Upper; Suspension Ball Joint; Ball Joint
- Position: Front Upper
- Replaces: 5086672AB, 5086672AC
- Item Weight: 1.90 Pounds
- Item Dimensions: 3.3 x 4.9 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68214646AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
2005 Dodge Ram 2500 Lower Ball Joint Part Number: 5086980AC
Product Specifications- Other Name: Balljoint - Lower Control Arm; Suspension Ball Joint; Ball Joint
- Position: Lower
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5086980AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
2005 Dodge Ram 2500 Ball Joint Parts and Q&A
- Q: How to Maintain a Ball Joint on 2005 Dodge Ram 2500?A: First, remove the tire and wheel assembly and below that, remove the brake caliper and rotor. Weld the tie rod to the steering knuckle and then remove the lower ball joint nut tilting the vehicle downwards. Then, separate the lower ball joint from the knuckle using tool number 8677. Shift the halfshaft aside and hold it so it won't fall if your car is equipped. On HD 4X2 models, discard the snap ring from the bottom of the control arm assembly. To increase the life of the tool and for it to function properly during installation and removal, cover the threaded sections with explicit pressured lubrication. Press the ball joint on the lower control arm with the special tools C-4212-F, 8698-2 and 8698-3. During installation, fit the ball joint to the control arm and push it into place with tools C-4212-F, 8698-1 and 8698-3. Cover the ball joint with its boot and position the flange over the ball joint staking locations around the flange by drilling and driving using a chisel and hammer on LD models. Install the snap ring for HD 4X2 models, unclip the support for the halfshaft and if it is present, clip it in again after. Afterward, insert the steering knuckle and tie rod end into their holding spots in the steering knuckle. Tighten the halfshaft nut to 251 Nm (185 ft. lbs.) if fitted; after that, set in the brake caliper and rotor and then reshoulding the tire and wheel assembly. verified the car's height and corrected the wheel alignment.
Related 2005 Dodge Ram 2500 Parts
2005 Dodge Ram 2500 Track Bar
2005 Dodge Ram 2500 Coil Springs
2005 Dodge Ram 2500 Steering Knuckle
2005 Dodge Ram 2500 Wheel Bearing
2005 Dodge Ram 2500 Axle Shaft Seal
2005 Dodge Ram 2500 Coil Spring Insulator
2005 Dodge Ram 2500 Control Arm
2005 Dodge Ram 2500 Control Arm Bushing
2005 Dodge Ram 2500 Shock Absorber
2005 Dodge Ram 2500 Sway Bar Bracket
2005 Dodge Ram 2500 Sway Bar Link
2005 Dodge Ram 2500 Wheel Hub