How to Maintain and Fix a Seat Belt and Retractor on 2005 Dodge Sprinter 3500?

The first step is to block the signal of the supplemental restraint system by removing and isolating the battery negative cable; leave the cable disconnected for about two minutes to allow the capacitor inside the mechanism to discharge. Check all seat belts, their buckles, mounts, retractors and anchors to see if they're properly installed and look for any damage. If you find any cuts, fraying or tears, change the belts; all attachments should be tight. When removing a front seat belt anchor, push the front seat all the way forward, unsnap the plastic cover from the screw, remove the screw and the anchor will also come out. Uninstall the B-pillar trim on the inside and, while inside the car, unlink the driver from the height adjuster. Next, bring the front seat belt and lower anchor through the holes in the trim, from the back. Take out the nut holding the seat belt turning loop to the height adjuster, then disconnect the wire harness connector for the seat belt tensioner from the retractor's initiator receptacle. Unscrew the back screw on the front seat belt retractor, located at the rear of the lower B-pillar and pull it out from the car. After placing the front seat belt and retractor near the B-pillar's lower end, slide the guide on the retractor to go into the notch and tighten its screw to 35 Nm (26 ft. lbs.). Put the wire harness connector of the seat belt tensioner back into place and make sure you hear a noticeable click when you fasten everything securely. Place the front seat belt loop on the seat height adjustment mechanism, tighten the nut to 35 Nm (26 ft. lbs.), direct the front seat belt and lower anchor down through the height adjuster trim and snap on the trim panel. Place the lower front anchor to the outside edge of your seat frame, tighten the screw at 35 Nm (26 ft. lbs.) and fix the plastic cover onto the screw if one is available. Only reattach the negative battery cable after the SRSC test procedure is done.

OEM 2005 Dodge Sprinter 3500 Seat Belt

Seat Safety Belt

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Seat Belts found

View related parts
2005 Dodge Sprinter 3500 Lap & Shoulder Belt, Rear Part Number: 5103834AA
$129.12 MSRP: $163.68
You Save: $34.56 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seat Belt - Retractor; Seat Belt Lap and Shoulder Belt, Rear; Belt & Retractor; Seat Belt Retractor
- Position: Rear
- Item Weight: 1.70 Pounds
- Item Dimensions: 5.9 x 5.0 x 4.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5103834AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Dodge Sprinter 3500 Submodels:
- Base | 5 Cyl 2.7 L DIESEL
View related parts
2005 Dodge Sprinter 3500 Lap & Shoulder Belt, Front Driver Side Part Number: 5103812AA
Product Specifications
- Other Name: Seatbelt - Front Outer; Seat Belt Lap and Shoulder Belt, Front Left; Belt & Retractor; Seat Belt Front Outer
- Position: Front Driver Side
- Item Weight: 3.70 Pounds
- Item Dimensions: 17.1 x 8.1 x 5.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5103812AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Dodge Sprinter 3500 Submodels:
- Base | 5 Cyl 2.7 L DIESEL
View related parts
2005 Dodge Sprinter 3500 Lap & Shoulder Belt, Front Passenger Side Part Number: 5125026AA
Product Specifications
- Other Name: Seatbelt - Front Outer; Seat Belt Lap and Shoulder Belt, Front Right; Belt & Retractor; Seat Belt Front Outer
- Position: Front Passenger Side
- Item Weight: 3.80 Pounds
- Item Dimensions: 17.4 x 5.1 x 8.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5125026AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Dodge Sprinter 3500 Submodels:
- Base | 5 Cyl 2.7 L DIESEL
View related parts
2005 Dodge Sprinter 3500 Lap & Shoulder Belt, Rear Part Number: 5125014AA
Product Specifications
- Other Name: Seat Belt - Retractor; Seat Belt Lap and Shoulder Belt, Rear; Belt & Retractor; Seat Belt Retractor
- Position: Rear
- Item Weight: 1.70 Pounds
- Item Dimensions: 6.2 x 6.1 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5125014AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Dodge Sprinter 3500 Submodels:
- Base | 5 Cyl 2.7 L DIESEL
View related parts
2005 Dodge Sprinter 3500 Buckle, Front Driver Side Part Number: 5103811AA
Product Specifications
- Other Name: Seat Belt - Buckle Half; Seat Belt Receptacle, Front Left; Latch; Seat Belt Buckle Half
- Position: Front Driver Side
- Item Weight: 0.80 Pounds
- Item Dimensions: 7.4 x 3.2 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5103811AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Dodge Sprinter 3500 Submodels:
- Base | 5 Cyl 2.7 L DIESEL
View related parts
2005 Dodge Sprinter 3500 Buckle, Front Passenger Side Part Number: 5103810AA
Product Specifications
- Other Name: Seat Belt - Buckle Half; Seat Belt Receptacle, Front Right; Latch; Seat Belt Buckle Half
- Position: Front Passenger Side
- Item Weight: 0.90 Pounds
- Item Dimensions: 14.5 x 9.8 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5103810AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Dodge Sprinter 3500 Submodels:
- Base | 5 Cyl 2.7 L DIESEL
View related parts
2005 Dodge Sprinter 3500 Center Buckle, Rear Part Number: 1LK95DX9AA
Product Specifications
- Other Name: Seat Belt - Buckle Half; Seat Belt Receptacle, Front Center, Rear; Buckle; Latch; Seat Belt Buckle Half
- Position: Rear
- Replaces: 5104502AA
- Item Weight: 0.70 Pounds
- Item Dimensions: 4.4 x 4.6 x 1.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 1LK95DX9AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Dodge Sprinter 3500 Submodels:
- Base | 5 Cyl 2.7 L DIESEL, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.5 L GAS
View related parts
2005 Dodge Sprinter 3500 Lap & Shoulder Belt, Front Passenger Side Part Number: 5103835AA
Product Specifications
- Other Name: Seatbelt - Front Outer; Seat Belt Lap and Shoulder Belt, Front Right; Belt & Retractor; Seat Belt Front Outer
- Position: Front Passenger Side
- Item Weight: 3.70 Pounds
- Item Dimensions: 17.6 x 8.4 x 4.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5103835AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Dodge Sprinter 3500 Submodels:
- Base | 5 Cyl 2.7 L DIESEL
View related parts
2005 Dodge Sprinter 3500 Lower Cover, Rear Part Number: 5133484AA
Product Specifications
- Other Name: Cap - Seat Belt; Seat Belt Anchor Plate Cover, Rear Lower; Cover Seat Belt
- Position: Rear Lower
- Item Weight: 0.50 Pounds
- Item Dimensions: 1.0 x 1.0 x 0.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5133484AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2005 Dodge Sprinter 3500 Submodels:
- Base | 5 Cyl 2.7 L DIESEL

2005 Dodge Sprinter 3500 Seat Belt Parts and Q&A

Q: How to Maintain and Fix a Seat Belt and Retractor on 2005 Dodge Sprinter 3500?
A: The first step is to block the signal of the supplemental restraint system by removing and isolating the battery negative cable; leave the cable disconnected for about two minutes to allow the capacitor inside the mechanism to discharge. Check all seat belts, their buckles, mounts, retractors and anchors to see if they're properly installed and look for any damage. If you find any cuts, fraying or tears, change the belts; all attachments should be tight. When removing a front seat belt anchor, push the front seat all the way forward, unsnap the plastic cover from the screw, remove the screw and the anchor will also come out. Uninstall the B-pillar trim on the inside and, while inside the car, unlink the driver from the height adjuster. Next, bring the front seat belt and lower anchor through the holes in the trim, from the back. Take out the nut holding the seat belt turning loop to the height adjuster, then disconnect the wire harness connector for the seat belt tensioner from the retractor's initiator receptacle. Unscrew the back screw on the front seat belt retractor, located at the rear of the lower B-pillar and pull it out from the car. After placing the front seat belt and retractor near the B-pillar's lower end, slide the guide on the retractor to go into the notch and tighten its screw to 35 Nm (26 ft. lbs.). Put the wire harness connector of the seat belt tensioner back into place and make sure you hear a noticeable click when you fasten everything securely. Place the front seat belt loop on the seat height adjustment mechanism, tighten the nut to 35 Nm (26 ft. lbs.), direct the front seat belt and lower anchor down through the height adjuster trim and snap on the trim panel. Place the lower front anchor to the outside edge of your seat frame, tighten the screw at 35 Nm (26 ft. lbs.) and fix the plastic cover onto the screw if one is available. Only reattach the negative battery cable after the SRSC test procedure is done.