How to Install a Front Cross-Member on 2007 Chrysler Sebring?

The first step is to fit the O2 sensor on the catalytic converter, add the heat shield and secure it with fasteners. After that, put on the heat shield push pins and fasten the bolts that secure the steering gear to the top crossmember of the suspension. Place the front suspension crossmember on the vehicle body and loosely bolt one end of the rear of the crossmember to the frame rail torque boxes. Slide the ball joint nut and the rear roll torque mount through hole, fastening it to 50 Nm (37 ft. lbs). Slide the stabilizer link fastener over the strut and then mount the lower control arms. Attach the crossmember to the frame rail torque boxes with tightened bolts, using 135 Nm (100 ft. lb) torque and carry out the same procedure for the cross member reinforcement with 55 Nm (41 ft. lb) torque. After installing the stay brackets and securing with 55 Nm (41 ft. lbs) of torque, set the fore/aft crossmember onto its supports. When you are done, set the vehicle lower to the ground and align the front end before adjusting it.

OEM 2007 Chrysler Sebring Front Cross-Member

Front Engine Cross Member

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Front Cross-Members found

View related parts
2007 Chrysler Sebring Engine Cradle, Front Part Number: 5085819AJ
$583.95 MSRP: $852.00
You Save: $268.05 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Crossmember - Front Suspension; Suspension Subframe Crossmember, Front; Suspension Crossmember; Crossmember; Crossmember Front Suspension
- Position: Front
- Replaces: 5085819AC, 5085819AF, 5085819AG, 5085819AD, 5085819AE, 5085819AH
- Item Weight: 47.80 Pounds
- Item Dimensions: 42.3 x 23.2 x 10.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5085819AJ
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Chrysler Sebring Submodels:
- Base, LX, Limited, Touring | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2007 Chrysler Sebring Floor Crossmember, Front Passenger Side Part Number: 5155114AC
$106.50 MSRP: $225.00
You Save: $118.50 (53%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Crossmember - Front Floor; Floor Pan Crossmember, Front Right, Right; Crossmember Front Floor
- Position: Front Passenger Side
- Replaces: 5155114AB
- Item Weight: 3.70 Pounds
- Item Dimensions: 34.8 x 5.6 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5155114AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Chrysler Sebring Submodels:
- Base, LX, Limited, Touring | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2007 Chrysler Sebring Crossmember, Front Center Part Number: 5076416AC
$157.49 MSRP: $232.00
You Save: $74.51 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Crossmember - Front Floor; Floor Pan Crossmember, Center, Front; Crossmember Front Floor
- Position: Front Center
- Replaces: 5076416AB
- Item Weight: 2.10 Pounds
- Item Dimensions: 27.3 x 9.3 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5076416AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Chrysler Sebring Submodels:
- Base, LX, Limited, Touring | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2007 Chrysler Sebring Floor Crossmember, Front Driver Side Part Number: 5155115AC
$180.15 MSRP: $265.00
You Save: $84.85 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Crossmember - Front Floor; Floor Pan Crossmember, Front Left, Left; Crossmember Front Floor
- Position: Front Driver Side
- Replaces: 5155115AB
- Item Weight: 3.70 Pounds
- Item Dimensions: 23.7 x 6.4 x 3.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5155115AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Chrysler Sebring Submodels:
- Base, LX, Limited, Touring | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
2007 Chrysler Sebring Front Crossmember Part Number: 5272647AF
$270.79 MSRP: $400.00
You Save: $129.21 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Crossmember - Front Frame; Engine Mount Crossmember, Front; Engine Mount Bracket, Front; Engine Mount Crossmember; Fore/Aft Crossmember; Crossmember Front Suspension; Crossmember Front Frame
- Position: Front
- Replaces: 5272647AD, 5272647AE
- Item Weight: 15.80 Pounds
- Item Dimensions: 39.9 x 27.3 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5272647AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Chrysler Sebring Submodels:
- Base, LX, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS

2007 Chrysler Sebring Front Cross-Member Parts and Q&A

Q: How to Install a Front Cross-Member on 2007 Chrysler Sebring?
A: The first step is to fit the O2 sensor on the catalytic converter, add the heat shield and secure it with fasteners. After that, put on the heat shield push pins and fasten the bolts that secure the steering gear to the top crossmember of the suspension. Place the front suspension crossmember on the vehicle body and loosely bolt one end of the rear of the crossmember to the frame rail torque boxes. Slide the ball joint nut and the rear roll torque mount through hole, fastening it to 50 Nm (37 ft. lbs). Slide the stabilizer link fastener over the strut and then mount the lower control arms. Attach the crossmember to the frame rail torque boxes with tightened bolts, using 135 Nm (100 ft. lb) torque and carry out the same procedure for the cross member reinforcement with 55 Nm (41 ft. lb) torque. After installing the stay brackets and securing with 55 Nm (41 ft. lbs) of torque, set the fore/aft crossmember onto its supports. When you are done, set the vehicle lower to the ground and align the front end before adjusting it.