Are Factory Recommended Brake Lines Essential for Quality and Durability on Chrysler Concorde?

Use only the factory brake hose specified for your vehicle to guarantee quality, the proper length and longer endurance. Be sure the surfaces where the tube connects to the hose are smooth and clean, as you can't use the front and rear right or left hoses on any other side of the engine. New copper seal washers must be used on all Banjo Bolts and all the fittings should be tightened to their correct torques. Attach the Banjo connector to the caliper for the flexible front brake hose first and then secure its other end bracket to the frame so the hose does not twist too much. Slide the brake tube fitting onto the hose end fitting with your hand and secure all attaching screws and fittings to the correct torque while pointing out that the frame bracket keys in place correctly. For cars with rear disc brakes, link the brake flex hoses to the brake caliper on both sides: attach at the end with a Banjo bolt and then secure the other end to the flex hose/bracket on the rear suspension crossmember. After that, join the rear proportioning valve onto the flex hose and secure the steel brake tubing to the rear proportioning valve, using all specified fasteners.

How to Replace the Brake Line on Chrysler Concorde?

All bolt-on brake tubes on this car are connected using Iso Style Tubing Flares at all points except for the one between the rear proportioning valve and flex hose which is attached by a double inverted flare. When changing the chassis brake tubes, only double wall 4.75mm (3/16 inch) steel with the Prokote 2000 coating should be used. It is necessary to bend and flare brake tubing correctly and avoid guiding it against rough or heated areas, to avoid kinks during replacement. All tubes should be fastened with the proper clips and bolts and you should make sure the flexible hose between the master cylinder, junction block or antilock control unit remains protected. Take off the damaged section of the brake line tube with a Tubing Cutter, Special Tool C-3478-a or similar and make sure to ream out the inside so the flared tube ends seat well. Before flaring, be sure to put the tube nut over the tubing. For all service procedures, you must use 4.75 mm metric size tubing together with metric Iso tube flaring equipment. Iso style metric tubing flares can be made using Snap-On Flaring Tool Tfm-428 or an alternative. Make sure the end of the tubing is square and that it doesn't have any burrs before flaring it. Align the two jaws of the Flaring Tool with the tubing, but do not lock them before you run the tool. Lay the tubing so that it is in line with the top surface of the flaring tool bar assembly. Attach the suitable sized adaptor over the yoke assembly feed screw, so that it sits right over the opening of the brake line. Before tightening the adapter, coat the place where the adapter meets the brake tubing with rubber lubricant. Once all adjustments are made, tighten the screw enough so that the adaptor seats squarely on the bar assembly to finish a metric Iso tubing flare.

OEM Chrysler Concorde Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Brake Lines found

View related parts
Chrysler Concorde Flex Hose, Rear Passenger Side Part Number: 4779012AC
$162.02 MSRP: $239.00
You Save: $76.98 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose, Rear Right; Brake Hose; Brake Line; Hose Brake; Hydraulic Hose
- Position: Rear Passenger Side
- Replaced by: 4779012AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-1999 Chrysler Concorde | LX, LXi | 6 Cyl 2.7 L GAS, 6 Cyl 3.2 L GAS
View related parts
Chrysler Concorde Tube Assembly Part Number: 4779065AB
$201.20 MSRP: $269.00
You Save: $67.80 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Line - Brake Lines; Brake Hydraulic Line; Brake Tube; Tube Bundle Brake With Clips; Tube Bundle Brake; Brake Line
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2004 Chrysler Concorde | LX, LXi, Limited | 6 Cyl 2.7 L GAS, 6 Cyl 3.2 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Concorde Flex Hose, Front Driver Side Part Number: 4779121AA
$23.92 MSRP: $36.85
You Save: $12.93 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose, Front Left; Brake Hose; Brake Line; Hose Brake; Hydraulic Hose
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2004 Chrysler Concorde | LX, LXi, Limited | 6 Cyl 2.7 L GAS, 6 Cyl 3.2 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Concorde Flex Hose, Rear Driver Side Part Number: 4779013AD
$219.59 MSRP: $343.00
You Save: $123.41 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose, Rear Left; Brake Hose; Brake Line; Hose Brake; Hydraulic Hose
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Chrysler Concorde | LX, LXi | 6 Cyl 2.7 L GAS, 6 Cyl 3.2 L GAS
View related parts
Chrysler Concorde Flex Hose Part Number: 4582277
$13.60 MSRP: $17.24
You Save: $3.64 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Line Front Wheel Disc Brake Left; Brake Hose; Hose Assembly, Front Wheel Disc Brake, Right; Hose Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1993-1997 Chrysler Concorde | Base, LX, LXi | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Concorde Flex Hose, Front Part Number: 4582276
$13.60 MSRP: $17.24
You Save: $3.64 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Line Front Wheel; Brake Hose; Hose Assembly, Front Wheel Disc Brake, Right; Hose Brake
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1993-1997 Chrysler Concorde | Base, LX, LXi | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Concorde Flex Hose Part Number: 4779120AA
Product Specifications
- Other Name: Line - Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose Brake
- Replaced by: 4779120AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2004 Chrysler Concorde | LX, LXi, Limited | 6 Cyl 2.7 L GAS, 6 Cyl 3.2 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Concorde Flex Hose, Rear Driver Side Part Number: 4779013AC
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose, Rear Left; Brake Hose; Brake Line; Hose Brake; Hydraulic Hose
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-1999 Chrysler Concorde | LX, LXi | 6 Cyl 2.7 L GAS, 6 Cyl 3.2 L GAS
View related parts
Chrysler Concorde Flex Hose Part Number: 4695308
Product Specifications
- Other Name: Line - Brake; Brake Hose; Hose Assembly, Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chrysler Concorde | Base, LX, LXi | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Concorde Flex Hose, Rear Driver Side Part Number: 4779221AA
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose, Rear Left; Brake Hose; Brake Line; Hose Brake; Hydraulic Hose
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2004 Chrysler Concorde | LX, LXi, Limited | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Concorde Flex Hose, Rear Passenger Side Part Number: 4779220AA
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose, Rear Right; Brake Hose; Brake Line; Hose Brake; Hydraulic Hose
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2004 Chrysler Concorde | LX, LXi, Limited | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Concorde Flex Hose, Rear Driver Side Part Number: 4779013AE
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose, Rear Left; Brake Hose; Brake Line; Hose Brake; Hydraulic Hose
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001 Chrysler Concorde | LX, LXi | 6 Cyl 2.7 L GAS, 6 Cyl 3.2 L GAS
View related parts
Chrysler Concorde Flex Hose Part Number: 4695309
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose; Hydraulic Hose; Brake Hose; Brake Line; Hose Assembly, Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chrysler Concorde | Base, LX, LXi | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Concorde Flex Hose Part Number: 4582442
Product Specifications
- Other Name: Line; Brake Hydraulic Hose; Hydraulic Hose; Brake Hose; Brake Line; Hose Assembly, Rear; Hose Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1993-1997 Chrysler Concorde | Base, LX, LXi | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Concorde Flex Hose Part Number: 4582273
Product Specifications
- Other Name: Hose; Brake Hose; Hose Assembly, Rear; Hose Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1993-1997 Chrysler Concorde | Base, LX, LXi | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Concorde Brake Hose, Front Driver Side Part Number: 4779120AB
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose, Front Left, Front Right; Hydraulic Hose; Brake Line
- Position: Front Driver Side
- Replaces: 4779120AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2004 Chrysler Concorde | LX, LXi, Limited | 6 Cyl 2.7 L GAS, 6 Cyl 3.2 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Concorde Flex Hose, Rear Passenger Side Part Number: 4779012AD
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose, Rear Right; Brake Hose; Brake Line; Hose Brake; Hydraulic Hose
- Position: Rear Passenger Side
- Replaces: 4779012AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chrysler Concorde | LX, LXi | 6 Cyl 2.7 L GAS, 6 Cyl 3.2 L GAS

Chrysler Concorde Brake Line

Choose OEM Brake Line that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Brake Line follows strict manufacturing steps to lock in quality and fit. If your Chrysler Concorde matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Concorde parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Brake Line is one of the hydraulic brake lines that playing a crucial roll in Chrysler's full-sized sedan car Halting system for better safety on road. The functions of the Brake Line is to carry brake fluid from the master cylinder to the brake caliper pistons, which is essential on Chrysler Concorde which is a car that was produced between 1993 to 2004. Tough and efficient Brake Lines are incorporated into the different versions of the Concorde models such as the Concorde Base LX, Concorde LXi, as well as the Concorde Limited edition. For instance, the Brake Line comes in different types of materials, which include the corrosion resistant stainless steel and the flexible rubber hoses. The performance derived by the use of stainless steel Brake Line provides a firmer feel to pedals for any driving situation especially the sporting ones. More so, the direct replacement alternatives guarantee that the Brake Line is perfectly in place to retain the braking system's functionality. However analyzing the Brake Line, it is apparent that it goes far beyond the mere need and represents the company's goal - to ensure safety and performance of automobiles. It is uniquely designed and very strong, and has been approved in the automotive market as a Brake Line, and therefore drivers will be very comfortable driving cars that have been fitted with these brake lines since they will be assured of the efficiency of these cars. In conclusion it can be seen that the Brake Line is a favorable component that sets the comfort of the ride besides the safety of all passengers.

Chrysler Concorde Brake Line Parts and Q&A

Tube Assembly
4779065AB
Q: Are Factory Recommended Brake Lines Essential for Quality and Durability on Chrysler Concorde?
A:
Use only the factory brake hose specified for your vehicle to guarantee quality, the proper length and longer endurance. Be sure the surfaces where the tube connects to the hose are smooth and clean, as you can't use the front and rear right or left hoses on any other side of the engine. New copper seal washers must be used on all Banjo Bolts and all the fittings should be tightened to their correct torques. Attach the Banjo connector to the caliper for the flexible front brake hose first and then secure its other end bracket to the frame so the hose does not twist too much. Slide the brake tube fitting onto the hose end fitting with your hand and secure all attaching screws and fittings to the correct torque while pointing out that the frame bracket keys in place correctly. For cars with rear disc brakes, link the brake flex hoses to the Brake Caliper on both sides: attach at the end with a Banjo bolt and then secure the other end to the flex hose/bracket on the rear suspension crossmember. After that, join the rear proportioning valve onto the flex hose and secure the steel brake tubing to the rear proportioning valve, using all specified fasteners.
Flex Hose, Rear Driver Side
4779013AD
Q: How to Replace the Brake Line on Chrysler Concorde?
A:
All bolt-on brake tubes on this car are connected using Iso Style Tubing Flares at all points except for the one between the rear proportioning valve and flex hose which is attached by a double inverted flare. When changing the chassis brake tubes, only double wall 4.75mm (3/16 inch) steel with the Prokote 2000 coating should be used. It is necessary to bend and flare brake tubing correctly and avoid guiding it against rough or heated areas, to avoid kinks during replacement. All tubes should be fastened with the proper clips and bolts and you should make sure the flexible hose between the master cylinder, junction block or antilock control unit remains protected. Take off the damaged section of the brake line tube with a Tubing Cutter, Special Tool C-3478-a or similar and make sure to ream out the inside so the flared tube ends seat well. Before flaring, be sure to put the tube nut over the tubing. For all service procedures, you must use 4.75 mm metric size tubing together with metric Iso tube flaring equipment. Iso style metric tubing flares can be made using Snap-On Flaring Tool Tfm-428 or an alternative. Make sure the end of the tubing is square and that it doesn't have any burrs before flaring it. Align the two jaws of the Flaring Tool with the tubing, but do not lock them before you run the tool. Lay the tubing so that it is in line with the top surface of the flaring tool bar assembly. Attach the suitable sized adaptor over the yoke assembly feed screw, so that it sits right over the opening of the brake line. Before tightening the adapter, coat the place where the adapter meets the brake tubing with rubber lubricant. Once all adjustments are made, tighten the screw enough so that the adaptor seats squarely on the bar assembly to finish a metric Iso tubing flare.