JeepParts
My Garage
My Account
Cart
OEM Chrysler Concorde CV Boot
Axle Boot- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
3 CV Boots found
Chrysler Concorde Boot Kit Part Number: 4863722
Chrysler Concorde Inner Boot Part Number: 4728262
Chrysler Concorde Inner Boot Part Number: 4728261
Chrysler Concorde CV Boot
Choose OEM CV Boot that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each CV Boot follows strict manufacturing steps to lock in quality and fit. If your Chrysler Concorde matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Concorde parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.
The Chrysler Concorde CV Boot is an important part which emphasizes on the dependability as well as power of Chrysler's full-sized car model. Intended to safeguard the Constant Velocity (CV) joint, the CV Boot holds a very significant position in the continuum of power between the transaxle and the wheels for a superior driving experience. This is Chrysler Concorde compatible and is made from either rubber or plastic, that holds the lubricant while keeping the dirt out from the CV joint. On the Chrysler Concorde, it uses the Rzeppa joints on the outer of the drive shaft and tripod with or double offset for the inner ends fitting the suspension of the car. The CV Boot should also be checked up frequently, since, if worn out, the joint will fail, and this shows signs of noise and / or vibrations. Moreover, the Chrysler Concorde is safe and efficient, which is reflected by such a part as CV Boot, as it suggests the car's strong design. In particular, the Import Car Chrysler Concorde CV Boot is special on the automotive market because of its long-life use and universality in fitting Chrysler automobiles so that the drivers can Services their car with sureness. Therefore, the Chrysler Concorde CV Boot is the clear evidence of this company's direct focus on quality that includes, but not limited to, safety and durability of the driving process as well as the major parts of any car.
Chrysler Concorde CV Boot Parts and Q&A
- Q: How to Replace a CV Boot on the Outer CV Joint on Chrysler Concorde?A:Before renewing the CV boot on the outside, it is important to remove both driveshaft assemblies. To start, remove the drive shaft that will need a new boot. Then, take off the big clamp that holds the CV boot to the housing, plus the small clamp that holds the outer boot onto the shaft connector. Pull the boot off the outside of the CV joint housing and move it down the connecting shaft. After you clean the area, separate the ears on the outer CV joint assembly to remove its retaining snap ring and take off the CV joint assembly from the interconnecting shaft. After taking off the bad CV boot, clean the outer joint components and check for extra wear; if any part seems worn, the whole assembly should be replaced since it is not possible to repair its individual components. Slide the seal boot onto the connecting shaft retaining clamp, then the replacement outer CV boot. Attach the outer CV joint assembly to the interconnecting shaft by pushing it in until its snap ring is set in the groove. After that, open the seal boot envelope, leaving the rest of the grease back inside. Position the outer CV boot retaining clamp on the end of the interconnecting shaft, so that only the thinnest part of the shaft can be seen through the boot. Crimper tool C-4975 secures the boot onto the shaft, so ensure the seal does not become loose, is smooth and retains its original shape; as necessary, even out the pressure and mold it by hand. Set the black CV boot for the outer CV joint into the groove in the outer CV housing and clip the black CV boot in place at both ends of the joint. After that, secure the boot on the outer CV joint housing using the C-4975 crimping tool and put the driveshaft back onto the car.
