How to Remove and Install the Drive Belt for the Generator, Power Steering, and Air Conditioning on Chrysler Prowler?

Before removing the generator or power steering belt, loose the tensioner pulley nut and move the tensioner adjusting bolt until the belt is accessible. Once the generator/power steering belt is gone, lift the car with a hoist, undo the locking nut on the tensioner pulley and then loosen the adjusting bolt so the belt comes off. Look over the accessory drive belt to verify it's working correctly, not damaged and well tensioned; you should change it if it shows excessive wear, deformed cables or major glazing. Light cracking on the ribbed sides of a Poly-V belt with a back driven pulley is normal, but parallel cracking is not. Set the belt over the drive pulleys and use the Special Tool 7198, Belt Tension Gauge, to check its tension, tightening the belt tensioner adjusting bolt until the correct tautness is achieved and lastly tighten the tensioner pulley locking nut to 54 Nm (40 ft. lbs.). Slide the drive pulleys over the generator/power steering belt, place the back of the belt at the tensioner pulley and tighten the tensioner pulley locking nut to 54 Nm (40 ft. lbs.). Whenever setting up a new air conditioning belt, drive and leave the engine idling for around five minutes to run-in the belt and then re-adjust it to the right tension.

OEM Chrysler Prowler Drive Belt

Serpentine Belt

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Drive Belts found

View related parts
Chrysler Prowler Serpentine Belt Part Number: 4892479AB
$48.28 MSRP: $70.90
You Save: $22.62 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt - Accessory Drive; Drive Belt; Alternator Belt; Belt; Belt Accessory Drive
- Replaces: 4573013AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2002 Chrysler Prowler | Base | 3.5L V6, 6 Cyl 3.5 L GAS
View related parts
Chrysler Prowler Serpentine Belt Part Number: 4663950AF
Product Specifications
- Other Name: Belt - A/C Compressor; A/C Belt
- Replaces: 4663950AD, 4663950AE, 4663950AC, 4663950
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2002 Chrysler Prowler | Base | 3.5L V6, 6 Cyl 3.5 L GAS

Chrysler Prowler Drive Belt

Choose OEM Drive Belt that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Drive Belt follows strict manufacturing steps to lock in quality and fit. If your Chrysler Prowler matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Prowler parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Make Chrysler Prowler Drive Belt is a crucial part that highlights the credibility and dynamism of Chrysler's famous Prowler automobiles. Intended to link the engine to many parts including the alternator and the Air Conditioning compressor, the Drive Belt is an important cog in their Prowler's potent 3.5 L V6 power plant. Chrysler has been able to design serpentine, v-belts, and multi-groove belts of the Drive Belt as a way of increasing the level of traction and decreasing slippage. Such an evolution in Drive Belt also increases the performance while greatly enhancing the safety and efficiency of the Prowler. This particular product is suitable with various Prowler models and you are likely to expect to get up to 100000 miles out of it; however, earlier replacement might be needed in case of signs of wear. The Chrysler Prowler Drive Belt is a distinctive product in the automotive market because of technological advancement used in production that enhances the construction; it ensures the belt provides continuous power transmission for effective functioning of the Prowler to make the car more performing. As an essential component of the Prowler, the Drive Belt contributes to aiding in the performance of the automobile while, at the same time, adding to both the improvement of the automobile's mechanical integrity and the driving enjoyment that the automotive user would get from the automobile. To sum up, the Chrysler Prowler Drive Belt is not only an item necessary for the production and the operation of automobiles but is also an indication of Chrysler Company's hard work and frequent improvements in the line of automobiles.

Chrysler Prowler Drive Belt Parts and Q&A

Serpentine Belt
4892479AB
Q: How to Remove and Install the Drive Belt for the Generator, Power Steering, and Air Conditioning on Chrysler Prowler?
A:
Before removing the generator or power steering belt, loose the tensioner pulley nut and move the tensioner adjusting bolt until the belt is accessible. Once the generator/power steering belt is gone, lift the car with a hoist, undo the locking nut on the tensioner pulley and then loosen the adjusting bolt so the belt comes off. Look over the accessory drive belt to verify it's working correctly, not damaged and well tensioned; you should change it if it shows excessive wear, deformed cables or major glazing. Light cracking on the ribbed sides of a Poly-V belt with a back driven pulley is normal, but parallel cracking is not. Set the belt over the drive pulleys and use the Special Tool 7198, Belt Tension Gauge, to check its tension, tightening the belt tensioner adjusting bolt until the correct tautness is achieved and lastly tighten the tensioner pulley locking nut to 54 Nm (40 ft. lbs.). Slide the drive pulleys over the generator/power steering belt, place the back of the belt at the tensioner pulley and tighten the tensioner pulley locking nut to 54 Nm (40 ft. lbs.). Whenever setting up a new air conditioning belt, drive and leave the engine idling for around five minutes to run-in the belt and then re-adjust it to the right tension.