How to Service a Seat Switch for the Driver on Chrysler Sebring?

To start, open the hood and disconnect the negative battery cable remote terminal from the remote battery post. It is very important to detach and isolate the battery negative cable before fixing or working on any seat or power seat piece in cars with side air bags. Unplug your battery and give the car two minutes after disconnecting to allow the system capacitor to discharge and make sure the air bags are disabled. Then, take off the side shield from the seat cushion on any Model S and on hardtop models gently remove all knobs from the seat switch. Take out the attaching screws from the switch and remove the switch from the cushion side shield. Attach the switch in its proper place, use screws to secure it, add back the seat cushion knobs if you have them, set up the electrical connector wire on the switch and finish by reinstalling the side shield. With the battery on, bring the free end of the negative cable up to the remote battery post and attach it.

How to Maintain the Seat Switch for the Driver's Seat on Chrysler Sebring?

Open the hood first and take the negative battery cable remote terminal off the remote battery post to begin working on the driver seat switch. After you remove the battery's negative cable, make sure to wait at least two minutes for the capacitor to empty so that any side air bag deploys automatically during the engine check. After that, take out the side shield from the front seat cushion. Pry each knob off the seat switch carefully if you have a hardtop car. Release the screws on the switch and pull the switch out through the cushion side shield. To install, first set the switch into place, screw it to the seat, reinstall the knobs if required, join the electrical connector between the wiring and the switch and finally fix the seat cushion side shield. Make sure to hook the other negative battery cable back to its appointed post on the far distant battery since this step should be last.

OEM Chrysler Sebring Seat Switch

Seat Adjust Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Seat Switches found

View related parts
Chrysler Sebring Switch Part Number: 4608673AC
$26.83 MSRP: $154.00
You Save: $127.17 (83%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Heated Seat; Switch Heated Seat
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2006 Chrysler Sebring | Base, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Control Switch, Driver Side Part Number: 4601757AC
$96.02 MSRP: $146.00
You Save: $49.98 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Power Seat; Power Seat Switch, Front Left, Left; Power Seat Switch; Switch Assembly; Seat Switch; Adjust Handle; Adjuster Switch; Switch
- Position: Driver Side
- Replaces: 4601757AB, 5191951AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chrysler Sebring | 2.4L L4, 2.7L V6
- 1996 Chrysler Sebring
View related parts
Chrysler Sebring Seat Switch, Driver Side Part Number: 56049429AF
$334.24 MSRP: $498.00
You Save: $163.76 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Power Seat; Power Seat Switch, Front, Front Left, Left; Power Seat Switch; Adjust Switch; Switch
- Position: Driver Side
- Replaces: 56049429AE, 56049429AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Base, LX, Limited, Touring | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Sebring Control Switch, Front Passenger Side Part Number: 56049428AF
$63.78 MSRP: $95.55
You Save: $31.77 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Power Seat; Power Seat Switch, Front Right, Right; Seat Switch; Adjuster Switch; Adjust Switch; Switch
- Position: Front Passenger Side
- Replaces: 56049428AE, 56049428AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Base, LX, Limited, Touring | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Sebring Switch - Power Seat Part Number: 56049433AG
$74.71 MSRP: $112.00
You Save: $37.29 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SWITCH-POWER SEAT
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Base, LX, Limited, Touring | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Sebring Switch - Power Seat Part Number: 56049432AG
$72.45 MSRP: $161.00
You Save: $88.55 (55%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SWITCH-POWER SEAT
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Base, LX, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Sebring Switch Part Number: 4671232AB
Product Specifications
- Other Name: Switch - Power Seat; Power Seat Switch; Switch Power Seat
- Replaces: 4671232
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996-2000 Chrysler Sebring | JX, JXi | 2.0L L4, 2.4L L4, 2.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS

Chrysler Sebring Seat Switch

Choose OEM Seat Switch that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Seat Switch follows strict manufacturing steps to lock in quality and fit. If your Chrysler Sebring matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Sebring parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Chrysler Sebring Seat Switch Parts and Q&A

Control Switch, Driver Side
4601757AC
Q: How to Service a Seat Switch for the Driver on Chrysler Sebring?
A:
To start, open the hood and disconnect the negative Battery Cable remote terminal from the remote battery post. It is very important to detach and isolate the battery negative cable before fixing or working on any seat or power seat piece in cars with side air bags. Unplug your battery and give the car two minutes after disconnecting to allow the system capacitor to discharge and make sure the air bags are disabled. Then, take off the side shield from the seat cushion on any Model S and on hardtop models gently remove all knobs from the seat switch. Take out the attaching screws from the switch and remove the switch from the cushion side shield. Attach the switch in its proper place, use screws to secure it, add back the seat cushion knobs if you have them, set up the electrical connector wire on the switch and finish by reinstalling the side shield. With the battery on, bring the free end of the negative cable up to the remote battery post and attach it.
Switch
4608673AC
Q: How to Maintain the Seat Switch for the Driver's Seat on Chrysler Sebring?
A:
Open the hood first and take the negative battery cable remote terminal off the remote battery post to begin working on the driver seat switch. After you remove the battery's negative cable, make sure to wait at least two minutes for the capacitor to empty so that any side Air Bag deploys automatically during the engine check. After that, take out the side shield from the front seat cushion. Pry each knob off the seat switch carefully if you have a hardtop car. Release the screws on the switch and pull the switch out through the cushion side shield. To install, first set the switch into place, screw it to the seat, reinstall the knobs if required, join the electrical connector between the wiring and the switch and finally fix the seat cushion side shield. Make sure to hook the other negative battery cable back to its appointed post on the far distant battery since this step should be last.