How to Maintain a Rear Disc Brake Caliper on Chrysler Voyager?

Press the brake pedal firmly past about one inch and clamp it in this position using a brake pedal depressor tool before working on the caliper in the rear disc brake. Raise up the vehicle and take out the rear wheel and its tire assembly. Take off the banjo bolt from the brake caliper and throw out the two washers that come off together. Take out the bolts holding the disc brake caliper to the adapter guide pin and then pull up on the rear of the caliper so that you can lift the front out from the adapter's front abutment. If you must change the brake rotors, first undo the retainer clips and pull the rotor straight off of the studs. Before installation, push in the caliper piston and when the rotor is taken off, affix the rotor flat to the hub. Move the caliper and caliper shoes very gently to the rotor adapter without bending the guide pin bushings. Tighten the caliper guide pin bolts to 35 Nm (26 ft. lbs.) as you install them and be careful to not create a cross-thread. For installation, get new special washers, thread them on the brake hose and at the fitting, slide the banjo bolt through and tighten to 47 Nm (35 ft. lbs.). Attach the wheel and tire assembly and remember to tighten the wheel stud nuts by sequence from half specification to the full value of 135 Nm (100 ft. lbs.). Slide the vehicle down, take the brake pedal depressor out, remove air bubbles, conduct a road test and check if the brake shoes are working correctly.

How to Service and Repair a Front Brake Caliper on Chrysler Voyager?

To repair the front caliper, first step on the brake pedal past its first inch and keep the brake pedal depressor there while working, so that no fluid drains from the master cylinder. Lift the vehicle and take out the tire and wheel from the front side. Open the banjo bolt on the brake hose and get rid of the two washers that fall out. Unscrew both guide pin bolts and then pull the brake caliper from the adapter. When putting it in place, the caliper piston must be pushed all the way into the bore or you can use a C-clamp along with a wood piece to do it. Place the brake caliper and shoes on the rotor and adapter and install the guide pin bolts to 35 Nm (26 ft. lbs.), ensuring you don't cross-thread them. Attach the anti-rattle clip to the outside side of the caliper, stretching it past the abutments so the holes are filled. Carefully slide a new special copper washer on each end of the fitting, then attach the brake hose and tighten the sillcock to 47 Nm (35 ft. lbs.). Attach the wheel and tire, then tighten the stud nuts according to the given order to reach 135 Nm (100 ft. lbs.). Hold the vehicle down, disconnect the brake pedal depressor, evacuate the hydraulic brake system into the caliper and drive the car to see if the brakes are seating properly.

OEM Chrysler Voyager Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Brake Calipers found

View related parts
Chrysler Voyager Intake Manifold, Rear Part Number: 5019808AA
$393.19 MSRP: $500.00
You Save: $106.81 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear; Caliper; Caliper Disc Brake; Brake Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2003 Chrysler Voyager | Base, Ec, LX | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Voyager Caliper Part Number: 68509084AA
$134.43 MSRP: $199.00
You Save: $64.57 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chrysler Voyager | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager Caliper, Front Driver Side Part Number: 68509085AA
$135.56 MSRP: $202.00
You Save: $66.44 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chrysler Voyager | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager Caliper Part Number: 68546278AA
$165.02 MSRP: $247.00
You Save: $81.98 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2025 Chrysler Voyager | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager Caliper, Front Driver Side Part Number: 68546277AA
$165.02 MSRP: $247.00
You Save: $81.98 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2025 Chrysler Voyager | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager Caliper, Front Driver Side Part Number: 68144161AA
$178.30 MSRP: $262.00
You Save: $83.70 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Caliper Assembly Disc Brake Front; Brake Caliper
- Position: Front Driver Side
- Replaces: 68144161AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020 Chrysler Voyager | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager Caliper, Front Passenger Side Part Number: 68144160AA
$178.30 MSRP: $262.00
You Save: $83.70 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Right; Caliper Assembly Disc Brake Front; Brake Caliper
- Position: Front Passenger Side
- Replaces: 68144160AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020 Chrysler Voyager | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager Caliper - Disc Brake Part Number: 68675593AA
$64.46 MSRP: $95.25
You Save: $30.79 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER-DISC BRAKE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2025 Chrysler Voyager | LX | 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager CALIPER-DISC BRAKE Part Number: 68675592AA
$64.46 MSRP: $95.25
You Save: $30.79 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2025 Chrysler Voyager | LX | 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager CALIPER-DISC BRAKE Part Number: 68675552AA
$72.65 MSRP: $108.00
You Save: $35.35 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2025 Chrysler Voyager | LX | 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager Caliper, Rear Driver Side Part Number: 68318173AB
$292.73 MSRP: $430.00
You Save: $137.27 (32%)
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Left; Caliper Assembly Disc Brake Rear; Brake Caliper
- Position: Rear Driver Side
- Replaces: 68318173AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chrysler Voyager | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager Caliper, Rear Passenger Side Part Number: 68318172AB
$285.51 MSRP: $430.00
You Save: $144.49 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Right; Caliper Assembly Disc Brake Rear; Brake Caliper
- Position: Rear Passenger Side
- Replaces: 68318172AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chrysler Voyager | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager Caliper Part Number: 5003891AC
Product Specifications
- Other Name: Caliper - Disc Brake; Brake Caliper
- Replaces: 5003891AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Chrysler Voyager | Base, SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Voyager Caliper, Front Passenger Side Part Number: 5139900AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front, Front Right; Caliper Disc Brake; Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2003 Chrysler Voyager | Base, Ec, LX | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Voyager Caliper, Front Driver Side Part Number: 5139901AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Caliper Disc Brake; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2003 Chrysler Voyager | Base, Ec, LX | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Voyager Caliper Assembly, Front Driver Side Part Number: 5010033AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Caliper; Caliper Disc Brake; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Chrysler Voyager | Base, SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Voyager Caliper Assembly, Front Passenger Side Part Number: 5010032AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Right; Caliper; Caliper Disc Brake; Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Chrysler Voyager | Base, SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Voyager Caliper, Front Passenger Side Part Number: 5019807AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Right; Caliper Disc Brake; Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2003 Chrysler Voyager | Base, Ec, LX | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Voyager Caliper, Front Driver Side Part Number: 5019806AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Caliper Disc Brake; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2003 Chrysler Voyager | Base, Ec, LX | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Voyager Steering Column Part Number: 5066106AC
Product Specifications
- Other Name: Column - Steering; Column Assembly; Caliper
- Replaces: 5066106AB, 5103440AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Chrysler Voyager | Base, SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS

Chrysler Voyager Brake Caliper

Choose OEM Brake Caliper that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Brake Caliper follows strict manufacturing steps to lock in quality and fit. If your Chrysler Voyager matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Voyager parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

There is no doubt that Brake Caliper plays a very important role in the Chrysler Voyager vehicles and its reliability and performance. This vital section converts the hydraulic pressure from the master cylinder into the mechanical force needed to apply the brake pads onto the rotors, thus slowing down or in some cases, stopping the motor vehicle. Chrysler has designed the Voyager to utilize two primary types of brake calipers: These include: the fixed and the floating kinds of foreign exchange reserves. Fixed have multiple pistons to match the pressure and floating slides over the rotor to apply pressure where maintenance is crucial in avoiding the uneven wear of the pads. The Brake Caliper comprises highly resistant castings, cast iron and steel so that the component can be long-lasting and functional. Checking and servicing of brake caliper are important to avoid some problems like brake drag or fluid leak because they will affect the safe and efficient operation of the vehicle. The Brake Caliper products are designed for different Voyager models, improving the entire experience of driving, as well as the safe control of the car depending on the model. Most noteworthy is the highly durability of the Brake Caliper and also the fact that performance options can be ordered to enhance on the stopping power. Brake Caliper is one of the most vital parts of Chrysler Voyager vehicles because of its reliability and safety assurance for the vehicles during the drive.

Chrysler Voyager Brake Caliper Parts and Q&A

Intake Manifold, Rear
5019808AA
Q: How to Maintain a Rear Disc Brake Caliper on Chrysler Voyager?
A:
Press the brake pedal firmly past about one inch and clamp it in this position using a brake pedal depressor tool before working on the caliper in the rear disc brake. Raise up the vehicle and take out the rear wheel and its tire assembly. Take off the banjo bolt from the brake caliper and throw out the two washers that come off together. Take out the bolts holding the disc brake caliper to the adapter guide pin and then pull up on the rear of the caliper so that you can lift the front out from the adapter's front abutment. If you must change the brake rotors, first undo the retainer clips and pull the rotor straight off of the studs. Before installation, push in the caliper piston and when the rotor is taken off, affix the rotor flat to the hub. Move the caliper and caliper shoes very gently to the rotor adapter without bending the guide pin bushings. Tighten the caliper guide pin bolts to 35 Nm (26 ft. lbs.) as you install them and be careful to not create a cross-thread. For installation, get new special washers, thread them on the brake hose and at the fitting, slide the banjo bolt through and tighten to 47 Nm (35 ft. lbs.). Attach the wheel and tire assembly and remember to tighten the wheel stud nuts by sequence from half specification to the full value of 135 Nm (100 ft. lbs.). Slide the vehicle down, take the brake pedal depressor out, remove air bubbles, conduct a road test and check if the brake shoes are working correctly.
Caliper, Front Driver Side
5019806AA
Q: How to Service and Repair a Front Brake Caliper on Chrysler Voyager?
A:
To repair the front caliper, first step on the brake pedal past its first inch and keep the brake pedal depressor there while working, so that no fluid drains from the master cylinder. Lift the vehicle and take out the tire and wheel from the front side. Open the banjo bolt on the brake hose and get rid of the two washers that fall out. Unscrew both guide pin bolts and then pull the brake caliper from the adapter. When putting it in place, the caliper piston must be pushed all the way into the bore or you can use a C-clamp along with a wood piece to do it. Place the brake caliper and shoes on the rotor and adapter and install the guide pin bolts to 35 Nm (26 ft. lbs.), ensuring you don't cross-thread them. Attach the anti-rattle clip to the outside side of the caliper, stretching it past the abutments so the holes are filled. Carefully slide a new special copper washer on each end of the fitting, then attach the brake hose and tighten the sillcock to 47 Nm (35 ft. lbs.). Attach the wheel and tire, then tighten the stud nuts according to the given order to reach 135 Nm (100 ft. lbs.). Hold the vehicle down, disconnect the brake pedal depressor, evacuate the hydraulic brake system into the caliper and drive the car to see if the brakes are seating properly.