How to Replace the Axle Shaft and CV Boot on Dodge Avenger?

First, take off the halfshaft assembly to remove the outer boot from the front half shaft. Pull off the main boot retaining clamp from the CV joint housing and then remove the small boot clamp that holds the CV joint outer boot on the interconnecting shaft. Descend the sliding boot to the bottom of the interconnecting shaft once you've removed it from the upper end. Remove any dirt from around the outer CV joint and surrounding interconnecting shaft. Place the interconnecting shaft into a vise, cover its ends and tap the end of the CV joint housing gently to pop it away from the internal circlip. Slide the end of the outer CV joint off the shaft and use taps if it is too tight. Whenever you reassemble, always fit a brand new circlip. Before sliding off the outer CV joint seal, pull out the large circlip on the center of the interconnecting shaft. Also, it's important to carefully inspect and clean the outer joint assembly, as well as the interconnecting joint for signs of additional wear; if there are any worn areas, the halfshaft assembly should be replaced since its parts cannot be serviced.

How to Properly Remove and Install an Axle Shaft on Dodge Avenger?

Slacken the drive shaft nut while tying the special tool's cord to any solid part nearby. Insert some tools into the wheel well to help you push out the drive shaft and inner shaft assembly. If the drive shaft and inner shaft are firmly attached to the transaxle, lightly whack the center bearing bracket using a plastic hammer to separate them. Put a pry bar inside the new connection hole between the transaxle case and the drive shaft and push to remove the drive shaft. Don't try to loosen the drive shaft nut by applying vehicle weight to the wheel bearing; if you have to, use a special tool-MB990998-to hold up the bearing. Be sure that the oil seal and rotor are not damaged for the installation. Connect the drive shaft washer to the wheel bearing, tighten the drive shaft nut with the correct tool and check that the wheel does not have any load before you finish tightening. If you can't match the holes, tighten the nut to a maximum of 254 Nm (188 ft. lbs.), add the cotter pin to the nearest non-matching holes, then bend it strong. Especially check the drive shaft boot for damage, the ball joints for wear and do an inspection of the spline part.

OEM Dodge Avenger Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Axle Shafts found

View related parts
Dodge Avenger Axle Assembly, Front Driver Side Part Number: 68067361AB
$335.29 MSRP: $497.00
You Save: $161.71 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Left; Constant Velocity Axle; Axle Shaft; Shaft Front Drive; CV Axle Assembly
- Position: Front Driver Side
- Replaces: 5273545AB, 5273545AC, 5273545AE, 68067361AA, 5273545AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2014 Dodge Avenger | 3.5L V6, 3.6L V6
View related parts
Dodge Avenger Axle Assembly, Front Passenger Side Part Number: 5273558AG
$397.75 MSRP: $599.00
You Save: $201.25 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Right; Constant Velocity Axle; Axle Shaft; Shaft Front Drive; CV Axle Assembly
- Position: Front Passenger Side
- Replaces: 5273558AB, 5273558AF, 5273558AE, 5273558AD, 5273558AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2009 Dodge Avenger | R/T, SE, SXT | 2.4L L4, 4 Cyl 2.4 L GAS
View related parts
Dodge Avenger Axle Assembly, Front Passenger Side Part Number: 5273546AF
$396.08 MSRP: $574.00
You Save: $177.92 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Right; Constant Velocity Axle; Axle Shaft; Shaft Front Drive; CV Axle Assembly
- Position: Front Passenger Side
- Replaces: 5273546AC, 5273546AB, 5273546AE, 5273546AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2014 Dodge Avenger | 3.5L V6, 3.6L V6
View related parts
Dodge Avenger Axle Assembly, Front Passenger Side Part Number: 5085130AB
$261.75 MSRP: $587.00
You Save: $325.25 (56%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Right; Constant Velocity Axle; Axle Shaft; Shaft Front Drive; CV Axle Assembly
- Position: Front Passenger Side
- Replaces: 5085130AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2014 Dodge Avenger | Express, Lux, Mainstreet, R/T, SE, SXT | 2.4L L4, 4 Cyl 2.4 L GAS
View related parts
Dodge Avenger Axle Assembly, Front Passenger Side Part Number: 5085185AF
$81.02 MSRP: $116.00
You Save: $34.98 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Right; Constant Velocity Axle; Axle Shaft; Shaft Front Drive One Piece Replaces Original Two Piece Shaft; Shaft Front Drive; CV Axle Assembly
- Position: Front Passenger Side
- Replaces: 5085185AE, 5085185AB, 5085185AD, 5085185AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Dodge Avenger | R/T, SE, SXT | 2.7L V6, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Dodge Avenger Axle Assembly, Front Part Number: MR430492
Product Specifications
- Other Name: Shaft Front Axle; Axle Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1999 Dodge Avenger | Base, ES | 4 Cyl 2.0 L GAS
View related parts
Dodge Avenger Axle Assembly Part Number: MR430486
Product Specifications
- Other Name: Shaft; Constant Velocity Axle; CV Axle Assembly; Axle Shaft; Shaft Front Axle
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Avenger | Base, ES | 6 Cyl 2.5 L GAS
View related parts
Dodge Avenger Axle Assembly, Front Part Number: MR430485
Product Specifications
- Other Name: Shaft - Front Axle; Constant Velocity Axle; CV Axle Assembly; Axle Shaft; Shaft Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Avenger | Base, ES | 6 Cyl 2.5 L GAS
View related parts
Dodge Avenger Axle Assembly, Front Part Number: MR430484
Product Specifications
- Other Name: Shaft Front Axle; Constant Velocity Axle; CV Axle Assembly; Axle Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Avenger | Base, ES | 6 Cyl 2.5 L GAS
View related parts
Dodge Avenger Axle Assembly, Front Part Number: MR430483
Product Specifications
- Other Name: Shaft Front Axle; Constant Velocity Axle; CV Axle Assembly; Axle Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Avenger | Base, ES | 6 Cyl 2.5 L GAS
View related parts
Dodge Avenger Axle Assembly, Front Part Number: MR196209
Product Specifications
- Other Name: Shaft Front Drive; Constant Velocity Axle; CV Axle Assembly; Axle Shaft; Shaft Assembly, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1999 Dodge Avenger | Base, ES | 4 Cyl 2.0 L GAS
View related parts
Dodge Avenger Axle Assembly, Front Part Number: MR165586
Product Specifications
- Other Name: Shaft Front Drive; Shaft Assembly, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1999 Dodge Avenger | Base, ES | 4 Cyl 2.0 L GAS
View related parts
Dodge Avenger Stub Shaft Part Number: MB936685
Product Specifications
- Other Name: Shaft Axle; Axle Shaft; Shaft; Shaft, Inner
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Avenger | Base, ES | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Avenger Axle Assembly, Rear Passenger Side Part Number: 5085100AB
Product Specifications
- Other Name: Shaft - Axle Half; CV Axle Assembly, Rear Right; Axle Shaft; Shaft Axle Half
- Position: Rear Passenger Side
- Replaces: 5085100AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Avenger | R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Dodge Avenger Axle Assembly, Rear Driver Side Part Number: 5085099AB
Product Specifications
- Other Name: Shaft - Axle Half; CV Axle Assembly, Rear Left; Axle Shaft; Shaft Axle Half
- Position: Rear Driver Side
- Replaces: 5085099AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Avenger | R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Dodge Avenger Axle Assembly, Front Part Number: MR430491
Product Specifications
- Other Name: Shaft - Front Axle; Axle Shaft; Shaft Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1999 Dodge Avenger | Base, ES | 4 Cyl 2.0 L GAS
View related parts
Dodge Avenger Axle Assembly, Front Driver Side Part Number: 5273763AG
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Left; Axle Shaft; Shaft Front Drive
- Position: Front Driver Side
- Replaces: 5273763AD, 5273763AE, 5273763AC, 5273763AF, 5273763AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2009 Dodge Avenger | R/T, SE, SXT | 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Dodge Avenger Axle Assembly, Front Driver Side Part Number: 52123559AB
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Left; Axle Shaft; Shaft Front Drive
- Position: Front Driver Side
- Replaces: 52123559AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Dodge Avenger | Express, Lux, Mainstreet, SE, SXT | 2.4L L4, 4 Cyl 2.4 L GAS
View related parts
Dodge Avenger Axle Assembly, Front Driver Side Part Number: 5085180AG
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Left; Constant Velocity Axle; Axle Shaft; Shaft Front Drive; CV Axle Assembly
- Position: Front Driver Side
- Replaces: 5085180AB, 5085180AE, 5085180AF, 5085180AD, 5085180AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2014 Dodge Avenger | Express, Lux, Mainstreet, R/T, SE, SXT | 2.4L L4, 2.7L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Avenger Axle Assembly, Front Passenger Side Part Number: 52123584AB
Product Specifications
- Other Name: Shaft - Front Drive; CV Axle Assembly, Front Right; Constant Velocity Axle; Axle Shaft; Shaft Front Drive; CV Axle Assembly
- Position: Front Passenger Side
- Replaces: 52123584AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Dodge Avenger | Express, Lux, Mainstreet, SE, SXT | 2.4L L4, 4 Cyl 2.4 L GAS

Dodge Avenger Axle Shaft

Choose OEM Axle Shaft that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Axle Shaft follows strict manufacturing steps to lock in quality and fit. If your Dodge Avenger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Avenger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

In Dodge Avenger vehicles the Axle Shaft is important in transmitting power from the differential to the drive wheels so they can rotate freelance for better grip during cornering. Normally made of strong steel, such axle shafts help to meet the requirements of driving, secure correct positioning of wheels, and support weight of the vehicle. Some of the Dodge Avenger models incorporate halfshafts, these have splined ends that engage the differential and wheel hubs. This design provides an enhanced power transfer especially in automobiles with independent suspension systems. Changes in design might have occurred over the years such as different axle shafts configurations while the main duty of this component is the same regardless of the make or Manufacturer. Maintenance is critical periodically because such parts as CV joints or axle bearings wear out, this compromises performance through noise, vibration and the like. In general, their support role cannot be overemphasized as far as the functionality of this particular model of the Dodge brand - the Avenger is concerned.

Dodge Avenger Axle Shaft Parts and Q&A

Axle Assembly, Front Driver Side
68067361AB
Q: How to Replace the Axle Shaft and CV Boot on Dodge Avenger?
A:
First, take off the halfshaft assembly to remove the outer boot from the front half shaft. Pull off the main boot retaining clamp from the CV joint housing and then remove the small boot clamp that holds the CV joint outer boot on the interconnecting shaft. Descend the sliding boot to the bottom of the interconnecting shaft once you've removed it from the upper end. Remove any dirt from around the outer CV joint and surrounding interconnecting shaft. Place the interconnecting shaft into a vise, cover its ends and tap the end of the CV joint housing gently to pop it away from the internal circlip. Slide the end of the outer CV joint off the shaft and use taps if it is too tight. Whenever you reassemble, always fit a brand new circlip. Before sliding off the outer CV joint seal, pull out the large circlip on the center of the interconnecting shaft. Also, it's important to carefully inspect and clean the outer joint assembly, as well as the interconnecting joint for signs of additional wear; if there are any worn areas, the halfshaft assembly should be replaced since its parts cannot be serviced.
Axle Assembly, Front
MR430483
Q: How to Properly Remove and Install an Axle Shaft on Dodge Avenger?
A:
Slacken the drive shaft nut while tying the special tool's cord to any solid part nearby. Insert some tools into the wheel well to help you push out the drive shaft and inner shaft assembly. If the drive shaft and inner shaft are firmly attached to the transaxle, lightly whack the center bearing bracket using a plastic hammer to separate them. Put a pry bar inside the new connection hole between the transaxle case and the drive shaft and push to remove the drive shaft. Don't try to loosen the drive shaft nut by applying vehicle weight to the Wheel Bearing; if you have to, use a special tool-MB990998-to hold up the bearing. Be sure that the oil seal and rotor are not damaged for the installation. Connect the drive shaft washer to the wheel bearing, tighten the drive shaft nut with the correct tool and check that the wheel does not have any load before you finish tightening. If you can't match the holes, tighten the nut to a maximum of 254 Nm (188 ft. lbs.), add the cotter pin to the nearest non-matching holes, then bend it strong. Especially check the drive shaft boot for damage, the Ball Joints for wear and do an inspection of the spline part.