How to Properly Install a Brake Caliper on Dodge Avenger?

Start by completely retracting the caliper piston back into the bore with a C-clamp and add a wood block over it to keep it from getting damaged. Following this, position the brake pad onto the inboard part of the caliper and push the clip into its places in the depressed areas of the caliper beyond the raised edge of the bead. Slide the disc brake caliper so the outer brake pad is over the inner brake pad and rotor, then connect the caliper to the adapter, being careful not to harm the guide pin boots along the way. The first time you install the guide pin bolts, place the bolt with the sleeve into the upper mounting site. Adjust the outer holes of the caliper guide pin to match with those on the adapter bracket and screw in both lower and upper guide pin bolts until tightened to 43 Nm (32 ft. lbs.). Work the rear brake flex hose into the brake caliper and tighten the fitting to a torque of 15 Nm (133 in. lbs.). Route and place the brake flex hose into the trailing link bracket and snap it in place with the clip. Put the brake tube nut onto the end of the brake flex hose and tighten it to 17 Nm (150 in. lbs.). The wheel and tire assembly should be installed by hand, with the bolts tightened to 135 Nm or 100 ft. lbs. Adjust the vehicle to a lower position, pull out the brake pedal holding tool and bleed the caliper as is required. Conduct a brief road test which will reveal any problems with the brakes and help set the brake shoes in place.

How to Remove and Replace a Rear Brake Caliper on Dodge Avenger?

You can remove the master cylinder by pressing the brake pedal with a brake pedal holding tool, holding it past an inch to stop the brake fluid from draining. After that, lift and stabilize the vehicle, then take out the three wheel mounting nuts and the whole rear tire and wheel assembly. Loosen and remove the nut from the brake tube at the rear flex hose. Then, pop open the clip that holds the flex hose to the trailing link mounted bracket and remove the hose from the bracket. Loosen and take out the brake flex hose from the brake caliper. As you remove the caliper guide pin bolts, notice that one has a sleeve; this bolt should go back in the upper mounting hole when you are done. Disconnect both brake caliper guide pin bolts and slide out the disc brake caliper assembly, each outboard and inboard brake pad and the rotor from the disc brake adapter bracket. Next, lift the retaining clip for the brake pad over the caliper's raised point to pull out the outboard brake pad.

OEM Dodge Avenger Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Brake Calipers found

View related parts
Dodge Avenger Caliper, Rear Passenger Side Part Number: 5191268AA
$85.72 MSRP: $129.00
You Save: $43.28 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Right; Caliper Assembly Disc Brake Rear; Brake Caliper
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2014 Dodge Avenger | Express, Heat, Lux, Mainstreet, R/T, SE, SXT, SXT Plus | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX
View related parts
Dodge Avenger Caliper, Front Driver Side Part Number: 5191239AA
$113.04 MSRP: $171.00
You Save: $57.96 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Left; Caliper Assembly Disc Brake Front; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2014 Dodge Avenger | Express, Heat, Lux, Mainstreet, R/T, SE, SXT, SXT Plus | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX
View related parts
Dodge Avenger Caliper, Rear Driver Side Part Number: 5191267AA
$85.72 MSRP: $129.00
You Save: $43.28 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Left; Caliper Assembly Disc Brake Rear; Brake Caliper
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2014 Dodge Avenger | Express, Heat, Lux, Mainstreet, R/T, SE, SXT, SXT Plus | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX
View related parts
Dodge Avenger Caliper, Front Passenger Side Part Number: 5191238AA
$130.02 MSRP: $181.00
You Save: $50.98 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Right; Caliper Assembly Disc Brake Front; Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2014 Dodge Avenger | Express, Heat, Lux, Mainstreet, R/T, SE, SXT, SXT Plus | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX
View related parts
Dodge Avenger Caliper Part Number: MB928410
Product Specifications
- Other Name: Caliper Package, Front Left; Caliper Disc Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Avenger | Base, ES | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Avenger Caliper, Rear Passenger Side Part Number: MR129584
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Right; Caliper Package, Rear Brake; Caliper Disc Brake
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Avenger | Base, ES | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Avenger Caliper Assembly, Rear Driver Side Part Number: MR129583
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Left; Caliper; Caliper Package, Rear Brake; Caliper Disc Brake; Brake Caliper
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Avenger | Base, ES | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Avenger Caliper Part Number: MB928411
Product Specifications
- Other Name: Brake Caliper; Caliper Package, Front Right; Caliper Disc Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Avenger | Base, ES | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS

Dodge Avenger Brake Caliper

Choose OEM Brake Caliper that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Brake Caliper follows strict manufacturing steps to lock in quality and fit. If your Dodge Avenger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Avenger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Brake Caliper in Dodge Avenger A simple definition about this vehicle part is that is the one that transforms hydraulic pressure from the master cylinder into mechanical force. This force is mainly required to act upon the brake pads so that they can apply pressure on the rotors in order to slow down or stop the vehicle. Dodge Avenger Brake Calipers can be categorized into two main types: for example fixed and floating. Among the known types of brake calipers, one can distinguish fixed ones in which several pistons on both sides of the rotor apply pressure and floating, where there is a piston on one side and the caliper slide towards the rotor when the brakes are applied. Through the years, many Dodge Avenger Brake Calipers are available that comes from standard original equipment to performance tuned models. Performance calipers improve the vehicle's brake performance and has better appearance compared to the base model, made by using high-tech lightweight materials such as Aluminum Alloy and multiple pistons. Their maintenance includes periodic inspection and cleaning of the Brake Caliper since their defects may cause problems such as uneven pad wear, brake drag and hence affect the performance of the motor vehicle.

Dodge Avenger Brake Caliper Parts and Q&A

Caliper, Rear Passenger Side
5191268AA
Q: How to Properly Install a Brake Caliper on Dodge Avenger?
A:
Start by completely retracting the caliper piston back into the bore with a C-clamp and add a wood block over it to keep it from getting damaged. Following this, position the Brake Pad onto the inboard part of the caliper and push the clip into its places in the depressed areas of the caliper beyond the raised edge of the bead. Slide the disc brake caliper so the outer brake pad is over the inner brake pad and rotor, then connect the caliper to the adapter, being careful not to harm the guide pin boots along the way. The first time you install the guide pin bolts, place the bolt with the sleeve into the upper mounting site. Adjust the outer holes of the caliper guide pin to match with those on the adapter bracket and screw in both lower and upper guide pin bolts until tightened to 43 Nm (32 ft. lbs.). Work the rear brake flex hose into the brake caliper and tighten the fitting to a torque of 15 Nm (133 in. lbs.). Route and place the brake flex hose into the trailing link bracket and snap it in place with the clip. Put the brake tube nut onto the end of the brake flex hose and tighten it to 17 Nm (150 in. lbs.). The wheel and tire assembly should be installed by hand, with the bolts tightened to 135 Nm or 100 ft. lbs. Adjust the vehicle to a lower position, pull out the brake pedal holding tool and bleed the caliper as is required. Conduct a brief road test which will reveal any problems with the brakes and help set the brake shoes in place.
Caliper, Rear Driver Side
5191267AA
Q: How to Remove and Replace a Rear Brake Caliper on Dodge Avenger?
A:
You can remove the master cylinder by pressing the brake pedal with a brake pedal holding tool, holding it past an inch to stop the brake fluid from draining. After that, lift and stabilize the vehicle, then take out the three wheel mounting nuts and the whole rear tire and wheel assembly. Loosen and remove the nut from the brake tube at the rear flex hose. Then, pop open the clip that holds the flex hose to the trailing link mounted bracket and remove the hose from the bracket. Loosen and take out the brake flex hose from the brake caliper. As you remove the caliper guide pin bolts, notice that one has a sleeve; this bolt should go back in the upper mounting hole when you are done. Disconnect both brake caliper guide pin bolts and slide out the disc brake caliper assembly, each outboard and inboard Brake Pad and the rotor from the disc brake adapter bracket. Next, lift the retaining clip for the brake pad over the caliper's raised point to pull out the outboard brake pad.