How to Remove and Install a Rocker Arm While Handling the Camshaft and Lash Adjuster on Dodge Avenger?

Start by cleaning the lash adjuster if you want to use it again and have a special tool remove the rocker arms. With camshaft installation, put oil on the camshaft journals and the cams and make sure not to mix up the right and left bank camshafts; the right bank has a 4 mm slit in the back of the camshaft. The dowel pin of the camshaft should be set up correctly. When doing the installation of the lash adjuster, install it under the rocker arm first and then use the special tool MD998443 (or alternative) to secure it without losing any fuel. Bolt down the rocker shaft so it does not overlaunch the cams and then at a right angle in the plug guide, add the spring for the rocker shaft from above before taking out the lash adjuster-holding components. Check that the rectangular side of the rocker shaft is located under the camshaft. Before installing the camshaft oil seal, measure the cam height. If it is over 37.08 mm for the intake side or 36.45 mm for the exhaust side, substitute the camshaft. Always avoid contaminating lash adjusters and never open them, instead use only fresh diesel fuel to wash them. Fill three containers with enough diesel fuel so that the lash adjuster stands upright, clean the outside of container A, use a wire or special tool MD998442 to lower the steel ball and stroke the plunger five to ten times so the operation is smooth inside. Wash container B similarly to empty the pressure chamber and for container C, don't clean it-just put the lash adjuster straight up with the plunger pressed and the container should get enough diesel fuel. If the plunger cannot be moved and the lash adjuster tightens, go ahead and fill the vase again. Make sure the lash adjuster is standing upright so it does not spill and install it as soon as you can.

OEM Dodge Avenger Rocker Arm

Engine Rocker Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Rocker Arms found

View related parts
Dodge Avenger Exhaust Rocker Arms Part Number: 4663996
$73.76 MSRP: $113.00
You Save: $39.24 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm - Exhaust; Rocker Arm; Rocker Arm Exhaust
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Avenger | R/T | 6 Cyl 3.5 L GAS
View related parts
Dodge Avenger Intake Rocker Arm Part Number: 4573460
$44.50 MSRP: $90.25
You Save: $45.75 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm - Intake; Rocker Arm; Exhaust Rocker Arms; Arm Assembly, Right Intake Rocker; Rocker Arm Intake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Avenger | R/T | 6 Cyl 3.5 L GAS
View related parts
Dodge Avenger Intake Rocker Arm Part Number: 4573459
$44.50 MSRP: $90.25
You Save: $45.75 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm - Intake; Rocker Arm; Exhaust Rocker Arms; Arm Assembly, Left Intake Rocker; Rocker Arm Intake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Avenger | R/T | 6 Cyl 3.5 L GAS
View related parts
Dodge Avenger Rocker Arms Part Number: 5184296AH
$16.24 MSRP: $23.45
You Save: $7.21 (31%)
ADD TO CART
Product Specifications
- Other Name: Arm - Valve; Rocker Arm; Rocker Arm Valve
- Replaces: 5184296AG, 5184296AD, 5184296AE, 5184296AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Dodge Avenger | Express, Heat, Lux, Mainstreet, R/T, SE, SXT, SXT Plus | 3.6L V6, 6 Cyl 3.6 L FLEX
View related parts
Dodge Avenger Rocker Arms Part Number: MD167981
$14.57 MSRP: $26.80
You Save: $12.23 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm - Intake; Rocker Arm; Intake Rocker Arm; Arm, Inlet Valve Rocker (Front Valve); Rocker Arm Intake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Avenger | Base, ES | 6 Cyl 2.5 L GAS
View related parts
Dodge Avenger Rocker Arms Part Number: MD178782
$21.00 MSRP: $42.45
You Save: $21.45 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm - Exhaust; Rocker Arm; Exhaust Rocker Arms; Arm, Exhaust Valve Rocker; Rocker Arm Exhaust
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Avenger | Base, ES | 6 Cyl 2.5 L GAS
View related parts
Dodge Avenger Rocker Arms Part Number: MD167980
$15.94 MSRP: $32.20
You Save: $16.26 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm - Intake; Intake Rocker Arm; Arm, Inlet Valve Rocker (Rear Valve); Rocker Arm Intake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Avenger | Base, ES | 6 Cyl 2.5 L GAS
View related parts
Dodge Avenger Rocker Arms Part Number: 4884042AA
Product Specifications
- Other Name: Arm - Valve; Rocker Arm Valve Roller; Rocker Arm Valve
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1999 Dodge Avenger | Base, ES | 4 Cyl 2.0 L GAS
View related parts
Dodge Avenger Rocker Arms Part Number: 4792295AB
Product Specifications
- Other Name: Arm - Valve; Rocker Arm; Rocker Arm Inlet And Exhaust Valve
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Avenger | R/T, SE, SXT | 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS

Dodge Avenger Rocker Arm

Choose OEM Rocker Arm that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Rocker Arm follows strict manufacturing steps to lock in quality and fit. If your Dodge Avenger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Avenger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Rocker Arm is used in Dodge Avenger vehicles to enable the operation of the valvetrain system of the engine to guarantee the proper motion transfer from the pushrod to the intake as well as the exhaust valves. As a rule, it is made from stamped steel or aluminum, the Rocker Arm translates the up-and-down movement of the pushrod into the downward movement needed to open the valves. In high RPM applications like scooter, aluminum is used due to its light weight Other engines may include cast iron or forged carbon steel used in diesel engines. Some of the models that might be used in Dodge Avenger comprise of different kinds of Rocker Arms such as the traditional and roller rockers. Roller rockers utilize needle bearings that are be used in place of conventional metal on metal contact, thus improving performance. The rocker ratio in these engines also varies from 1.5:1 to 1.8:1 which enable bigger lift to the camshaft and improved engine performance. The new fulcrum bearings are also used in the stress conditions of high-RPM engines to deal with the stress and enhance the Rocker Arm system's durability in Dodge Avenger automobiles.

Dodge Avenger Rocker Arm Parts and Q&A

Rocker Arms
MD167981
Q: How to Remove and Install a Rocker Arm While Handling the Camshaft and Lash Adjuster on Dodge Avenger?
A:
Start by cleaning the Lash Adjuster if you want to use it again and have a special tool remove the rocker arms. With Camshaft installation, put oil on the camshaft journals and the cams and make sure not to mix up the right and left bank camshafts; the right bank has a 4 mm slit in the back of the camshaft. The dowel pin of the camshaft should be set up correctly. When doing the installation of the lash adjuster, install it under the rocker arm first and then use the special tool MD998443 (or alternative) to secure it without losing any fuel. Bolt down the rocker shaft so it does not overlaunch the cams and then at a right angle in the plug guide, add the spring for the rocker shaft from above before taking out the lash adjuster-holding components. Check that the rectangular side of the rocker shaft is located under the camshaft. Before installing the camshaft oil seal, measure the cam height. If it is over 37.08 mm for the intake side or 36.45 mm for the exhaust side, substitute the camshaft. Always avoid contaminating lash adjusters and never open them, instead use only fresh diesel fuel to wash them. Fill three containers with enough diesel fuel so that the lash adjuster stands upright, clean the outside of container A, use a wire or special tool MD998442 to lower the steel ball and stroke the plunger five to ten times so the operation is smooth inside. Wash container B similarly to empty the pressure chamber and for container C, don't clean it-just put the lash adjuster straight up with the plunger pressed and the container should get enough diesel fuel. If the plunger cannot be moved and the lash adjuster tightens, go ahead and fill the vase again. Make sure the lash adjuster is standing upright so it does not spill and install it as soon as you can.