How to Remove and Replace Rear Brake Pads on Dodge Challenger?

On all models except the SRT8, retract the rear brake caliper piston by removing the reservoir cap, squeezing the caliper and replacing the cap to avoid damaging the piston. Should the shield be removed, put anti-rattle clips on the upper and lower abutments of the caliper adapter. Take the film off the double sticky isolator brake pad if installed. Replace both inboard and outboard brake pads on the caliper adapter as they are the same and fit both ways. Insert the caliper guide pins into the caliper adapter to free space for the caliper mounting bosses during setup, next rotate the caliper upward and align its upper boss with the upper guide pin. Before fitting the upper caliper guide pin bolt, ensure the guides are clean and covered in adhesive or equivalent and tighten the bolt to 31 Nm (23 ft. lbs.) with the guide pin in position. Take the tire/wheel assembly out and replace it, torqueing the wheel mounting nuts to 150 Nm (110 ft. lbs.) or 190 Nm (140 ft. lbs.) if it's a police car. Use the brake pedal a few times to press the brake pads to the rotor and caliper and then check and adjust the brake fluid in the reservoir. Brake systems may be less effective when you use them for the first time after installing them. It is necessary to perform a burnish procedure whenever new brakes are installed on Police Package-equipped vehicles, always performing it safely at the police place of business. Be sure to test the car on the road and make several stops along the way so any foreign material left on the brake can wear off and the brake shoes can be properly seated in the fitting.

How to Remove and Replace Front Brake Pads on Dodge Challenger?

On these vehicles, to change the front brake pads, pull the piston(s) all the way back into the caliper bore(s) using the C-clamp or pressure with your hands. Should you remove the welded ribs, place anti-rattle clips between the upper and lower parts of the adapter. If you have removable film, take it off the double sticky isolator attached to the brake pad. Put installed new inboard and outboard brake pads on the caliper adapter, as both new pads can be placed on either side. Insert the guide pins of the caliper into the caliper adapter to allow clearing the caliper bosses for installation; then rotate the caliper downwards so that the upper mounting boss fits above the lower guide pin. Place and tighten the upper caliper guide pin bolt to 60 Nm (44 ft. lbs.) while supporting the guide pin still. Attach the tire and wheel assembly and fasten the wheel with nuts to 150 Nm (110 ft. lbs.) or use 190 Nm (140 ft. lbs.) for police cars. Lower the car and press the brake pedal several times so the pads reach the caliper and the rotor surface and next check and adjust the brake fluid in the reservoir. Note that following installation, the first few times you brake, the system may not have maximum efficiency until a burnish is performed and the police agency should do this in a controlled, purpose-built environment. After everything is set, begin a test drive and stop a few times to burnish off the brakes adequately.

OEM Dodge Challenger Brake Pads

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Brake Pads found

View related parts
Dodge Challenger Brake Pads, Rear Part Number: 5174327AC
$84.74 MSRP: $127.00
You Save: $42.26 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Rear Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Hardware Kit; Rear Pads; Pad Kit Rear Disc Brake; Disc Brake Pad Set
- Position: Rear
- Replaces: 5174327AA, 5174327AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2011 Dodge Challenger | R/T, SE, SRT8 | 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Brake Pads, Front Part Number: 5174311AC
$220.11 MSRP: $327.00
You Save: $106.89 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Front Disc Brake; Disc Brake Pad Set, Front; Disc Brake Hardware Kit; Disc Brake Pad Kit; Front Pads; Pad Kit Front Disc Brake Contains 4 Pads; Pad Kit Front Disc Brake
- Position: Front
- Replaces: 5174311AA, 5174311AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Challenger | R/T, SE, SRT8 | 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Challenger Brake Pads, Rear Part Number: 5142561AC
$58.47 MSRP: $144.00
You Save: $85.53 (60%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Rear Disc Brake; Disc Brake Pad Set, Rear; Rear Pads
- Position: Rear
- Replaces: 5142561AA, 5142561AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2020 Dodge Challenger | 392 Hemi Scat Pack Shaker, GT, R/T, R/T 392, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Scat Pack Widebody, R/T Shaker, Rallye Redline, Scat Pack, SE, SRT 392, SRT Demon, SRT Hellcat, SRT Hellcat Redeye, SRT Hellcat Redeye Widebody, SRT Hellcat Widebody, SRT Super Stock, SRT8, SXT, SXT Plus, T/A, T/A 392 | 3.5L V6, 3.6L V6, 5.7L V8, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.1L V8, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Brake Pads, Front Part Number: 68525329AC
$549.69 MSRP: $862.00
You Save: $312.31 (37%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Front Disc Brake; Front Pads
- Position: Front
- Replaces: 68525329AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2021-2023 Dodge Challenger | GT, R/T, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock, SXT, T/A 392 Widebody | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Front Disc Brake Pad Kit Part Number: 5142558AD
$93.99 MSRP: $145.00
You Save: $51.01 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Front Disc Brake, Pad Kit-Front Disc Brake; Front Pads
- Position: Front
- Replaces: 5142558AB, 5142558AA, 5142558AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2023 Dodge Challenger | 392 Hemi Scat Pack Shaker, GT, R/T, R/T 392, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, R/T Shaker, Rallye Redline, Scat Pack, SRT 392, SRT Demon, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock, SRT8, SXT, SXT Plus, T/A, T/A 392, T/A 392 Widebody | 3.5L V6, 3.6L V6, 5.7L V8, 6 Cyl 3.6 L GAS, 6.1L V8, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Brake Pads, Rear Part Number: 68504577AB
$117.59 MSRP: $180.00
You Save: $62.41 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Rear Disc Brake; Rear Pads
- Position: Rear
- Replaces: 68504577AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2021-2023 Dodge Challenger | GT, R/T, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock, SXT, T/A 392 Widebody | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Brake Pads, Front Part Number: 68144213AC
$148.08 MSRP: $226.00
You Save: $77.92 (35%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Front Disc Brake; Front Pads; Caliper
- Position: Front
- Replaces: 68144213AB, 68144213AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2020 Dodge Challenger | 392 Hemi Scat Pack Shaker, GT, R/T, R/T 392, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Scat Pack Widebody, R/T Shaker, Rallye Redline, Scat Pack, SE, SRT 392, SRT Demon, SRT Hellcat, SRT Hellcat Redeye, SRT Hellcat Redeye Widebody, SRT Hellcat Widebody, SRT Super Stock, SRT8, SXT, SXT Plus, T/A, T/A 392 | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Brake Pads, Gray/Orange, Front Part Number: 68248384AD
$165.51 MSRP: $254.00
You Save: $88.49 (35%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Front Disc Brake; Front Pads
- Position: Front
- Replaces: 68248384AC, 68248384AB, 68248384AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2020 Dodge Challenger | GT, R/T, R/T 392, R/T Scat Pack, R/T Scat Pack Widebody, SRT 392, SRT Demon, SRT Hellcat, SRT Hellcat Redeye, SRT Hellcat Redeye Widebody, SRT Hellcat Widebody, SRT Super Stock, SXT, SXT Plus, T/A, T/A 392 | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Brake Pads, Front Part Number: 5174001AD
$83.63 MSRP: $125.00
You Save: $41.37 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Front Disc Brake; Disc Brake Pad Set, Front; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Replaces: 5174001AA, 5174001AB, 5142555AA, 5174001AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2020 Dodge Challenger | 392 Hemi Scat Pack Shaker, GT, R/T, R/T 392, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Scat Pack Widebody, R/T Shaker, Rallye Redline, Scat Pack, SE, SRT 392, SRT Demon, SRT Hellcat, SRT Hellcat Redeye, SRT Hellcat Redeye Widebody, SRT Hellcat Widebody, SRT Super Stock, SRT8, SXT, SXT Plus, T/A, T/A 392 | 3.5L V6, 3.6L V6, 5.7L V8, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.1L V8, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Brake Pads, Rear Part Number: 68504576AB
$122.65 MSRP: $184.00
You Save: $61.35 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Rear Disc Brake; Rear Pads
- Position: Rear
- Replaces: 68504576AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2021-2023 Dodge Challenger | GT, R/T, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock, SXT, T/A 392 Widebody | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Brake Pads, Front Part Number: 68504575AB
$161.68 MSRP: $242.00
You Save: $80.32 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Front Disc Brake; Front Pads
- Position: Front
- Replaces: 68504575AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2021-2023 Dodge Challenger | GT, R/T, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock, SXT, T/A 392 Widebody | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Brake Pads, Front Part Number: 68504574AB
$161.68 MSRP: $242.00
You Save: $80.32 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Front Disc Brake; Front Pads
- Position: Front
- Replaces: 68504574AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2021-2023 Dodge Challenger | GT, R/T, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock, SXT, T/A 392 Widebody | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Brake Pads, Rear Part Number: 68501808AB
$168.37 MSRP: $251.00
You Save: $82.63 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit - Rear Disc Brake
- Position: Rear
- Replaces: 68501808AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2021-2023 Dodge Challenger | GT, R/T, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock, SXT, T/A 392 Widebody | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Brake Pads, Front Part Number: 68501805AB
$179.01 MSRP: $264.00
You Save: $84.99 (33%)
Product Specifications
- Other Name: Pad Kit - Front Disc Brake; Front Pads
- Position: Front
- Replaces: 68501805AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2021-2023 Dodge Challenger | GT, R/T, R/T Scat Pack, R/T Scat Pack Shaker Widebody, R/T Scat Pack Widebody, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock, SXT, T/A 392 Widebody | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Brake Pads, Rear Part Number: 68144223AD
$157.49 MSRP: $231.00
You Save: $73.51 (32%)
Product Specifications
- Other Name: Pad Kit - Rear Disc Brake; Disc Brake Pad Set, Rear; Rear Pads
- Position: Rear
- Replaces: 68144223AB, 68144223AC, 68144223AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2020 Dodge Challenger | 392 Hemi Scat Pack Shaker, GT, R/T, R/T 392, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Scat Pack Widebody, R/T Shaker, Rallye Redline, Scat Pack, SRT 392, SRT Demon, SRT Hellcat, SRT Hellcat Redeye, SRT Hellcat Redeye Widebody, SRT Hellcat Widebody, SRT Super Stock, SRT8, SXT, SXT Plus, T/A, T/A 392 | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L GAS, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Pad Kit - Front Disc Brake Part Number: 68147681AD
$199.41 MSRP: $294.00
You Save: $94.59 (33%)
Product Specifications
- Other Name: PAD KIT-FRONT DISC BRAKE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2017 Dodge Challenger | 392 Hemi Scat Pack Shaker, R/T, R/T 392, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Shaker, Rallye Redline, Scat Pack, SE, SRT 392, SRT Hellcat, SRT8, SXT, SXT Plus, T/A 392 | 3.5L V6, 3.6L V6, 5.7L V8, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.1L V8, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Brake Pads, Rear Part Number: 5142560AC
Product Specifications
- Other Name: Pad Kit - Rear Disc Brake; Disc Brake Pad Set, Rear; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaces: 5142560AB, 5142560AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2020 Dodge Challenger | 392 Hemi Scat Pack Shaker, GT, R/T, R/T 392, R/T Classic, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Scat Pack Widebody, R/T Shaker, Rallye Redline, Scat Pack, SE, SRT 392, SRT Demon, SRT Hellcat, SRT Hellcat Redeye, SRT Hellcat Redeye Widebody, SRT Hellcat Widebody, SRT Super Stock, SRT8, SXT, SXT Plus, T/A, T/A 392 | 3.5L V6, 3.6L V6, 5.7L V8, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.1L V8, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Challenger Brake Pads, Black, Front Part Number: 68307707AA
Product Specifications
- Other Name: Pad Kit - Front Disc Brake
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2018 Dodge Challenger | 392 Hemi Scat Pack Shaker, GT, R/T, R/T 392, R/T Plus, R/T Plus Shaker, R/T Scat Pack, R/T Shaker, SRT 392, SRT Demon, SRT Hellcat, SRT Hellcat Widebody, SXT, SXT Plus, Scat Pack, T/A, T/A 392 | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS

Dodge Challenger Brake Pads

Choose OEM Brake Pads that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Brake Pads follows strict manufacturing steps to lock in quality and fit. If your Dodge Challenger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Challenger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The friction from the Dodge Challenger Brake Pads slows or stops the vehicle by converting kinetic energy into heat. The steel backing plate of each pad is covered with a friction lining that is riveted or molded to the backing. The caliper presses two pads against each rotor. Dodge cars come standard with this design. As the lining wears, a vehicle's Brake Pads contain mechanical wear indicators or electronic sensors to let the driver know when they need replacing, which helps ensure the Dodge braking system stays within specifications. As long as the Challenger is fitted with Brake Pads thick enough, stopping distances will not become elongated, and pedal feel will remain predictable. The Brake Pads are designed to meet the requirements of Challenger drivers during daily commutes, errands, and leisurely cruises where the heat they generate is manageable and the discs can disperse the heat effectively without fading. During operation, eccentrically placed friction materials get deposited on the surface of the rotor and enhance grip, while the backing plate gives structural support. This means that reliable Brake Pads, sturdy rotors, and hydraulic calipers work together for consistent stopping. This means that reliable Dodge Challenger Brake Pads, sturdy rotors and hydraulic calipers work together for consistent stopping.

Dodge Challenger Brake Pads Parts and Q&A

Brake Pads, Rear
5174327AC
Q:
How to Remove and Replace Rear Brake Pads on Dodge Challenger?
A:
On all models except the SRT8, retract the rear brake caliper piston by removing the reservoir cap, squeezing the caliper and replacing the cap to avoid damaging the piston. Should the shield be removed, put anti-rattle clips on the upper and lower abutments of the caliper adapter. Take the film off the double sticky isolator brake pad if installed. Replace both inboard and outboard brake pads on the caliper adapter as they are the same and fit both ways. Insert the caliper guide pins into the caliper adapter to free space for the caliper mounting bosses during setup, next rotate the caliper upward and align its upper boss with the upper guide pin. Before fitting the upper caliper guide pin bolt, ensure the guides are clean and covered in adhesive or equivalent and tighten the bolt to 31 Nm (23 ft. lbs.) with the guide pin in position. Take the tire/wheel assembly out and replace it, torqueing the wheel mounting nuts to 150 Nm (110 ft. lbs.) or 190 Nm (140 ft. lbs.) if it's a police car. Use the brake pedal a few times to press the brake pads to the rotor and caliper and then check and adjust the brake fluid in the reservoir. Brake systems may be less effective when you use them for the first time after installing them. It is necessary to perform a burnish procedure whenever new brakes are installed on Police Package-equipped vehicles, always performing it safely at the police place of business. Be sure to test the car on the road and make several stops along the way so any foreign material left on the brake can wear off and the brake shoes can be properly seated in the fitting.
Brake Pads, Front
5174311AC
Q:
How to Remove and Replace Front Brake Pads on Dodge Challenger?
A:
On these vehicles, to change the front brake pads, pull the piston(s) all the way back into the caliper bore(s) using the C-clamp or pressure with your hands. Should you remove the welded ribs, place anti-rattle clips between the upper and lower parts of the adapter. If you have removable film, take it off the double sticky isolator attached to the brake pad. Put installed new inboard and outboard brake pads on the caliper adapter, as both new pads can be placed on either side. Insert the guide pins of the caliper into the caliper adapter to allow clearing the caliper bosses for installation; then rotate the caliper downwards so that the upper mounting boss fits above the lower guide pin. Place and tighten the upper caliper guide pin bolt to 60 Nm (44 ft. lbs.) while supporting the guide pin still. Attach the tire and wheel assembly and fasten the wheel with nuts to 150 Nm (110 ft. lbs.) or use 190 Nm (140 ft. lbs.) for police cars. Lower the car and press the brake pedal several times so the pads reach the caliper and the rotor surface and next check and adjust the brake fluid in the reservoir. Note that following installation, the first few times you brake, the system may not have maximum efficiency until a burnish is performed and the police agency should do this in a controlled, purpose-built environment. After everything is set, begin a test drive and stop a few times to burnish off the brakes adequately.