JeepParts
My Garage
My Account
Cart
OEM Dodge Charger Brake Booster
Brake Power Booster- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
7 Brake Boosters found
Dodge Charger Brake Booster Part Number: 68048544AA
$323.49 MSRP: $414.00You Save: $90.51 (22%)Ships in 1-2 Business Days
Dodge Charger Brake Booster Part Number: 68237808AC
$297.98 MSRP: $444.00You Save: $146.02 (33%)Ships in 1-2 Business Days
Dodge Charger Brake Booster Part Number: 68089130AD
$188.08 MSRP: $277.00You Save: $88.92 (33%)
Dodge Charger Brake Booster Part Number: 68033785AA
Dodge Charger Booster Part Number: 68020421AA
Dodge Charger Brake Booster Part Number: 5139152AA
Dodge Charger Brake Booster Part Number: 5139145AA
Dodge Charger Brake Booster
Choose OEM Brake Booster that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Brake Booster follows strict manufacturing steps to lock in quality and fit. If your Dodge Charger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Charger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.
This component known as the Brake Booster is very important especially in Dodge Charger since it helps in boosting the brakes to reduce the amount of pressure you need to apply in order to get the brakes working. This component works via a vacuum chamber that multiplies the hydraulic pressure developed by the master cylinder thus enhancing on the force applied by the driver on the brake pedal. Intake manifold gaskets on Dodge Charger models use a vacuum servo also referred to as a brake booster since it helps to minimize the force the driver has to apply when stopping their vehicle. Thus let it be mentioned that the brake booster operates only when the engine is running, and in the case of an engine shut down its usage is limited to few attempts of brake usage only.
Dodge Charger Brake Booster Parts and Q&A
- Q: How to Maintain and Fix a Brake Booster on Dodge Charger?A:For vacuum brake booster service, shift the driver's seat as far back as it can go and next disconnect the battery negative cable from the battery. After that, disconnect and take out the windshield wiper module and the master cylinder. If your vehicle is featured with MK25 and ESP, pull the wiring harness connector from the pedal travel sensor near power brake booster and from the active brake booster solenoid unit. With the vacuum switch on, disconnect the vacuum hose from the check valve on the booster's face, leaving check valve attached. Pull out the brake lamp switch and remove the booster push rod by putting a small screwdriver into place, then turning and sliding it off the end of the brake pedal pin. When you put the device back together, you ought to replace the retaining clip as part of the process. Take the booster push rod off the brake pedal pin, unscrew the four nuts holding the power brake booster in place and then pull the power brake booster some ways forward. Once it's free from the mounting area, remove it through the opening between the windshield and the cross-brace.
- Q: How to Install a Brake Booster on Dodge Charger?A:It's important to put a Newer booster seal on the push rod and mounting studs on the booster's rear before installing to keep leaks and failure at bay. The booster seal has to be installed over the push rod and the mounting studs first. Following that, insert the power brake booster under the cross-brace into the space above the windshield, positioning both the push rod and mounting studs through the dash. All nuts securing the power brake booster to the engine must be tightened to avoid vacuum problems. Slide the booster push rod onto the brake pedal pin, then hold it in place with the New (Original) retaining clip provided. Set up and fine-tune the brake lamp switch. Insert the vacuum hose into the check valve on the booster's face, while leaving the check valve in place. If your vehicle comes with Mk25 and Esp, attach the wiring harness to the pedal travel sensor on the power brake booster and to the active brake booster solenoid. Install the master cylinder now. Subsequently, installing the windshield wiper module is necessary. Now, attach the negative battery connection and bleed the brakes when it's required.
Related Dodge Charger Parts
Dodge Charger ABS Control Module
Dodge Charger Brake Caliper Bracket
Dodge Charger Brake Dust Shield
Dodge Charger Brake Fluid Level Sensor
Dodge Charger Brake Line
Dodge Charger Brake Master Cylinder
Dodge Charger Brake Pad
Dodge Charger Parking Brake Cable
Dodge Charger Vacuum Pump
Dodge Charger Wheel Cylinder
Dodge Charger Wheel Stud
Dodge Charger Yaw Sensor