How to Remove a Brake Master Cylinder on Dodge Charger?

To start, keep the power brake booster pumped down when the engine is off by pressing on the brake pedal until there is a firm response. Do not connect the negative battery cable to the post on the battery. Take out the access panel under the cowl to find the master cylinder. Thoroughly clean all parts of the reservoir and the master cylinder with Mopar(R) Brake Parts Cleaner that is comparable. Take out the connector from the brake fluid level sensor in the master cylinder brake fluid reservoir. Take out both primary and secondary brake tubes from the master cylinder and place sealing plugs in the open parts of the brake tubes. Both the master cylinder and the booster should be cleaned well before the master cylinder is removed, to avoid dirt getting into the booster. Lose the two nuts holding the master cylinder to the power brake booster and just pull the master cylinder away. Whenever the master cylinder is removed, the vacuum seal on the back should be taken off and replaced and it should not be broken by using sharp tools.

How to Install a Brake Master Cylinder on Dodge Charger?

First, insert brand new news brake fluid reservoir sealing grommets (2) into the brake master cylinder housing (1). Pour a little new brake fluid over the mounting area and press the reservoir firmly onto the sealing grommets as you slightly rock it. Make certain that the fluid reservoir is in contact with both sealing grommets (2). After that, fix the intake manifold to the head with the fluid reservoir mounting screw (3) and tighten it to 28 Nm (250 in. lbs.). Attach the end of the wiring harness connector (4) to the brake fluid level sensor (2) that is inside of the brake fluid reservoir (1). Place clean, fresh Mopar(R) Brake Fluid or an equal alternative in the master cylinder fluid reservoir (1). The last step is to put the access panel in the cowl area. Establish a reliable brake pedal before using the vehicle; if not, empty the entire brake hydraulic system and search for leaks. Drive on the road to make sure that the brakes work as they should.

OEM Dodge Charger Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Brake Master Cylinders found

View related parts
Dodge Charger Master Cylinder Part Number: 68033786AA
$201.02 MSRP: $305.00
You Save: $103.98 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Master Cylinder Part Number: 68048551AC
$222.07 MSRP: $331.00
You Save: $108.93 (33%)
ADD TO CART
Product Specifications
- Other Name: Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Replaces: 68048551AB, 68048551AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2023 Dodge Charger | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT8, SXT, SXT Plus, SXT Plus Leather, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody | 2.7L V6, 3.5L V6, 3.6L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.1L V8, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Master Cylinder Part Number: 5139153AA
$160.42 MSRP: $203.36
You Save: $42.94 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Master Cylinder Part Number: 5139148AA
$316.89 MSRP: $401.71
You Save: $84.82 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Charger | Base, Daytona R/T, Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Master Cylinder Part Number: 68048548AA
Product Specifications
- Other Name: Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Master Cylinder Part Number: 68033788AA
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Master Cylinder Part Number: 4509602
Product Specifications
- Other Name: Master Cylinder - Brake - Compensator 21Mm; Brake Master Cylinder; Master Cylinder, Complete
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1985-1987 Dodge Charger | 2.2, Base, Shelby | 4 Cyl 1.6 L GAS, 4 Cyl 2.2 L GAS

Dodge Charger Brake Master Cylinder

Choose OEM Brake Master Cylinder that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Brake Master Cylinder follows strict manufacturing steps to lock in quality and fit. If your Dodge Charger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Charger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The brake master cylinder is a system that is used in Dodge Charger vehicles with the main duty of translating the mechanical pressure created by the driver's foot into hydraulic pressure in order to facilitate control of brakes. It does so through utilizing hydraulic fluid to extend calipers or drum brakes enough to cause enough friction to halt movement of the car. The design incorporates dual circuit master cylinders with two piston, which enabled the other circuit to be active and provide brake power in the other if the initial one is faulty. Various Dodge Charger have used Cast Iron and Aluminium for the Brake Master Cylinders with different reservoir type, integral or external influencing Serviceability. Sometimes, the integral reservoirs are less complex as opposed to the exterior reservoirs, the exterior reservoirs are less difficult to access for fluid checks. But as time passes by there are such problems as leakages or internal problems that needs to be check in order to keep up the Dodge Charger's performance of Brake Master Cylinder.

Dodge Charger Brake Master Cylinder Parts and Q&A

Master Cylinder
68048551AC
Q: How to Remove a Brake Master Cylinder on Dodge Charger?
A:
To start, keep the power Brake Booster pumped down when the engine is off by pressing on the brake pedal until there is a firm response. Do not connect the negative Battery Cable to the post on the battery. Take out the access panel under the cowl to find the master cylinder. Thoroughly clean all parts of the reservoir and the master cylinder with Mopar(R) Brake Parts Cleaner that is comparable. Take out the connector from the brake fluid level sensor in the master cylinder brake fluid reservoir. Take out both primary and secondary brake tubes from the master cylinder and place sealing plugs in the open parts of the brake tubes. Both the master cylinder and the booster should be cleaned well before the master cylinder is removed, to avoid dirt getting into the booster. Lose the two nuts holding the master cylinder to the power brake booster and just pull the master cylinder away. Whenever the master cylinder is removed, the vacuum seal on the back should be taken off and replaced and it should not be broken by using sharp tools.
Master Cylinder
5139153AA
Q: How to Install a Brake Master Cylinder on Dodge Charger?
A:
First, insert brand new news brake fluid reservoir sealing grommets (2) into the brake master cylinder housing (1). Pour a little new brake fluid over the mounting area and press the reservoir firmly onto the sealing grommets as you slightly rock it. Make certain that the fluid reservoir is in contact with both sealing grommets (2). After that, fix the intake manifold to the head with the fluid reservoir mounting screw (3) and tighten it to 28 Nm (250 in. lbs.). Attach the end of the wiring harness connector (4) to the brake fluid level sensor (2) that is inside of the brake fluid reservoir (1). Place clean, fresh Mopar(R) Brake Fluid or an equal alternative in the master cylinder fluid reservoir (1). The last step is to put the access panel in the cowl area. Establish a reliable brake pedal before using the vehicle; if not, empty the entire brake hydraulic system and search for leaks. Drive on the road to make sure that the brakes work as they should.