How to Install a Shift Cable on Dodge Charger?

Start the installation of the shift cable by lowering the gearshift cable (1) through the dash panel down to the shifter assembly from the engine compartment. Once that's done, stick the grommet (2) onto the dash panel and hold the gearshift cable retainer (2) into the notch (2) in the shifter assembly. Place the gearshift cable onto the moveable pin on the shift lever and if necessary, loosen the screw used to adjust the cable length. Proceed by threading the gearshift cable (1) under the air conditioning lines and heater hoses (2) up to the transmission (3) manual lever and then lift the car. Turn the propeller shaft to see if it rotates; if so, adjust the transmission manual shift lever until it shows the PARK system is on. Take the gearshift cable and pass it through the bracket, then hook the cable eyelet onto the manual shift lever on the transmission (3). Adapt the suspension so that part of the front bumper just touches the ground, put the shifter into PARK and then tighten the adjustment screw (5) to 7 Nm (65 in.lbs.). Check the gear shift is operating well and need to bolt the shield covering the gearshift and park lock cables to the floorpan if required. Lastly, put in the floor console when it's required.

How to Maintain and Fix a Shift Cable on Dodge Charger?

Before beginning service or repair on the shift cable, put the transmission in PARK and raise the vehicle. Release the gearshift cable at the manual shift lever of the transmission and pull the cable from the mounting bracket. Lift the vehicle gently and take out the floor console if you need to reach the shift mechanism and its cables. Whenever necessary, disconnect the bolts that hold the gearshift and park lock shield to the floorpan, then remove the shield. After that, remove the gearshift cable from the pin on the shift lever and take the retainer from the opening in the shifter assembly. Remove the grommet under the dash panel and then take out the entire gearshift cable.

OEM Dodge Charger Shift Cable

Transmission Shift Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Shift Cables found

View related parts
Dodge Charger Shift Control Cable Part Number: 4578759AB
$147.18 MSRP: $222.00
You Save: $74.82 (34%)
ADD TO CART
Product Specifications
- Other Name: Cable - Gear Selector; Automatic Transmission Shifter Cable
- Replaces: 4578759AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT | 2.7L V6, 3.5L V6, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Shift Control Cable Part Number: 4670705AA
$101.13 MSRP: $155.00
You Save: $53.87 (35%)
ADD TO CART
Product Specifications
- Other Name: Cable - Gearshift Control; Automatic Transmission Shifter Cable; Cable Automatic Transmission Manual Parking Release; Cable Gearshift Control
- Replaces: 68066472AH, 68066472AC, 68066472AD, 68066472AE, 68066472AG, 68066472AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020 Dodge Charger
- 2012-2018 Dodge Charger | 3.6L V6, 5.7L V8
View related parts
Dodge Charger Shift Control Cable Part Number: 4670707AA
$54.17 MSRP: $80.55
You Save: $26.38 (33%)
ADD TO CART
Product Specifications
- Other Name: Cable - Gearshift Control; Automatic Transmission Shifter Cable; Cable Gearshift Control
- Replaces: 5038759AC, 5038759AF, 5038759AE, 5038759AD, 5038759AB, 5038759AG
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2023 Dodge Charger | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SXT, SXT Plus, SXT Plus Leather, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.2L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Shift Control Cable Part Number: 4578074AF
Product Specifications
- Other Name: Cable - Gear Selector; Automatic Transmission Shifter Cable
- Replaces: 4578074AB, 4578074AE, 4578074AD, 4578074AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT | 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Shift Control Cable Part Number: 4578758AB
Product Specifications
- Other Name: Cable - Gear Selector; Automatic Transmission Shifter Cable
- Replaces: 4578758AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Charger | Pursuit, R/T, SE, SRT8, SXT | 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Dodge Charger Shift Control Cable Part Number: 4670708AA
Product Specifications
- Other Name: Cable - Gearshift Control; Automatic Transmission Shifter Cable; Cable Gearshift Control
- Replaces: 68171664AE, 68171664AD, 68171664AB, 68171664AF, 68171664AG, 68171664AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2023 Dodge Charger | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SXT, SXT Plus, SXT Plus Leather, Scat Pack, Scat Pack 392 Widebody, Scat Pack Widebody | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS

Dodge Charger Shift Cable

Choose OEM Shift Cable that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Shift Cable follows strict manufacturing steps to lock in quality and fit. If your Dodge Charger matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Charger parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Dodge Charger Shift Cable Parts and Q&A

Shift Control Cable
4578074AF
Q: How to Install a Shift Cable on Dodge Charger?
A:
Start the installation of the shift cable by lowering the gearshift cable (1) through the dash panel down to the shifter assembly from the engine compartment. Once that's done, stick the grommet (2) onto the dash panel and hold the gearshift cable retainer (2) into the notch (2) in the shifter assembly. Place the gearshift cable onto the moveable pin on the shift lever and if necessary, loosen the screw used to adjust the cable length. Proceed by threading the gearshift cable (1) under the air conditioning lines and heater hoses (2) up to the transmission (3) manual lever and then lift the car. Turn the propeller shaft to see if it rotates; if so, adjust the transmission manual shift lever until it shows the PARK system is on. Take the gearshift cable and pass it through the bracket, then hook the cable eyelet onto the manual shift lever on the transmission (3). Adapt the suspension so that part of the front bumper just touches the ground, put the shifter into PARK and then tighten the adjustment screw (5) to 7 Nm (65 in.lbs.). Check the gear shift is operating well and need to bolt the shield covering the gearshift and park lock cables to the floorpan if required. Lastly, put in the floor console when it's required.
Shift Control Cable
4578759AB
Q: How to Maintain and Fix a Shift Cable on Dodge Charger?
A:
Before beginning service or repair on the shift cable, put the transmission in PARK and raise the vehicle. Release the gearshift cable at the manual shift lever of the transmission and pull the cable from the mounting bracket. Lift the vehicle gently and take out the floor console if you need to reach the shift mechanism and its cables. Whenever necessary, disconnect the bolts that hold the gearshift and park lock shield to the floorpan, then remove the shield. After that, remove the gearshift cable from the pin on the shift lever and take the retainer from the opening in the shifter assembly. Remove the grommet under the dash panel and then take out the entire gearshift cable.