How to Properly Burnish a New A/C Compressor Clutch on Dodge Durango?

Switch the A/C on for 5 seconds, switch it off for 5 seconds and do this for approximately 20 times after you've installed the new clutch. Place the A/C-heater controls in the A/C Recirculation Mode, set the blower motor at its highest level and drive the engine so that it goes between 1500 and 2000 rpm. By burnishing, the two contacting surfaces will remain held firmly and the compressor clutch torque will improve.

How to Service an A/C Compressor Clutch Assembly on Dodge Durango?

Before working on the clutch assembly, depart the negative battery cable from the terminal. Take off the air intake hose from both the air filter housing and the resonator, drain a little of the coolant and take out the upper radiator hose from the radiator and set it where it will not get in your way. After that, take out the radiator fan and its shroud and then the serpentine belt. Take the engine wire harness out of the connector on the compressor clutch field coil at the top of your A/C compressor. Carefully pull the compressor clutch field coil connection and wire lead off the bracket. Hold the clutch plate from rotating and remove the bolt using either a band-type oil filter wrench or strap wrench. Don't pry between the clutch plate and the pulley and bearing assembly to avoid damaging the clutch plate and try not to drop any clutch shims so you can reuse them during installation. Tap gently on the clutch plate with the plastic mallet to make it slide out of the compressor shaft and then remove both the clutch plate and shim. With Snap Ring Pliers 9764 or similar, remove the snap ring that holds the pulley and bearing assembly onto the A/C compressor front and then remove the assembly. Last, use Snap Ring Pliers 9764 or the similar tool to get the snap ring out and remove the front field coil of the A/C compressor.

OEM Dodge Durango A/C Compressor Clutch

Air Conditioning Clutch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 A/C Compressor Clutches found

View related parts
Dodge Durango Clutch Kit Part Number: 68068755AA
$35.28 MSRP: $83.65
You Save: $48.37 (58%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Clutch - A/C Compressor; A/C Compressor Clutch; Repair Kit; A/C Compressor Clutch Overhaul Kit includes snap rings, washers, screws, and bolts.
- Replaced by: 68068755AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2015 Dodge Durango | Citadel, Crew, Express, Heat, Limited, R/T, Rallye, SXT, Special Service | 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Dodge Durango Pulley Part Number: 68084278AB
$275.15 MSRP: $421.00
You Save: $145.85 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulley - A/C Compressor; A/C Compressor Clutch Pulley; Pulley Hub Kit A/C Compressor; A/C Compressor Clutch
- Replaces: 68084278AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2025 Dodge Durango | Citadel, Crew, Express, GT, GT Plus, GT Premium, Heat, Limited, Pursuit, Rallye, Special Service, SXT, SXT Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Durango Clutch Coil Part Number: 5003681AA
$191.78 MSRP: $291.00
You Save: $99.22 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil - A/C Clutch; A/C Compressor Clutch Coil; Clutch; Coil; Coil A/C Clutch; A/C Compressor Clutch
- Replaces: 5072863AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2015, 2004-2009 Dodge Durango | Adventurer, Citadel, Crew, Limited, R/T, SE, SLT, ST, SXT, Special Service | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Durango Hub Assembly Part Number: 68084274AB
$210.74 MSRP: $315.00
You Save: $104.26 (34%)
ADD TO CART
Product Specifications
- Other Name: Pulley - A/C Compressor; A/C Compressor Clutch Pulley; Serpentine Belt Drive Kit; Pulley Assembly; Clutch Plate & Hub Assembly; Pulley; Pulley Hub Kit A/C Compressor; A/C Compressor Clutch
- Replaces: 68084274AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2015 Dodge Durango | Citadel, Crew, Express, Heat, Limited, Rallye, Special Service, SXT | 3.6L V6, 6 Cyl 3.6 L FLEX
View related parts
Dodge Durango Clutch Coil Part Number: 68242651AA
$271.92 MSRP: $404.00
You Save: $132.08 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil - A/C Clutch; A/C Compressor Clutch Coil; Coil; Coil A/C Clutch; A/C Compressor Clutch
- Replaces: 68058043AA, 68058043AC, 68058043AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2015 Dodge Durango | Citadel, Crew, Express, Heat, Limited, Rallye, Special Service, SXT | 3.6L V6, 6 Cyl 3.6 L FLEX
View related parts
Dodge Durango Coil - A/C Clutch Part Number: 5140461AB
$172.83 MSRP: $263.00
You Save: $90.17 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: COIL-AIR CONDITIONING CLUTCH
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2015 Dodge Durango | Citadel, Crew, Limited, R/T, Special Service | 5.7L V8, 8 Cyl 5.7 L GAS
View related parts
Dodge Durango Repair Kit Part Number: 68034536AA
$10.84 MSRP: $21.55
You Save: $10.71 (50%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Clutch - A/C Compressor; A/C Compressor Clutch Pulley; Clutch Overhaul Kit A/C Compressor: Snap Rings, Shims, Pulley Bolt, Bracket, Screw.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2009 Dodge Durango | Adventurer, Limited, SE, SLT, SXT | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Dodge Durango Hub Assembly Part Number: 68084834AC
$260.78 MSRP: $395.00
You Save: $134.22 (34%)
ADD TO CART
Product Specifications
- Other Name: Pulley - A/C Compressor; A/C Compressor Clutch Pulley; Pulley Assembly; Clutch Plate & Hub Assembly; Pulley
- Replaces: 68084834AB, 68084834AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2015 Dodge Durango | Citadel, Crew, Limited, R/T, Special Service | 5.7L V8, 8 Cyl 5.7 L GAS
View related parts
Dodge Durango Clutch Coil Part Number: 68084275AB
$207.39 MSRP: $315.00
You Save: $107.61 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Coil - A/C Clutch; A/C Compressor Clutch Coil; Coil A/C Clutch; A/C Compressor Clutch
- Replaces: 68084275AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2025 Dodge Durango | Citadel, Crew, Express, GT, GT Plus, GT Premium, Heat, Limited, Pursuit, Rallye, Special Service, SXT, SXT Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Durango Clutch Kit Part Number: 68032119AA
$42.92 MSRP: $63.90
You Save: $20.98 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Clutch Package - A/C Compressor; A/C Compressor Clutch; Repair Kit; Clutch Overhaul Kit A/C Compressor with essential hardware components.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Dodge Durango | Limited, SE, SLT | 8 Cyl 5.7 L GAS
View related parts
Dodge Durango Clutch & Pulley Part Number: 5083077AA
Product Specifications
- Other Name: Clutch - A/C Compressor; A/C Compressor Clutch; Clutch Coil; Clutch; Clutch A/C Compressor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2003 Dodge Durango | SLT, SLT Plus, SXT, Sport | 8 Cyl 4.7 L GAS
View related parts
Dodge Durango Pulley Assembly Part Number: 5135993AA
Product Specifications
- Other Name: Pulley Kit - A/C Compressor; A/C Compressor Clutch Pulley; Serpentine Belt Drive Kit; Clutch; Pulley Hub Kit A/C Compressor; A/C Compressor Clutch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2007 Dodge Durango | Adventurer, Limited, SLT, ST, SXT | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Dodge Durango Clutch Coil Hardware Kit Part Number: 5135972AA
Product Specifications
- Other Name: Clutch Package - A/C Compressor; A/C Compressor Clutch; Clutch Overhaul Kit A/C Compressor: Includes Snap Rings, Shims, Pulley Bolt, Bracket, Screw.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2009 Dodge Durango | Adventurer, Limited, SE, SLT, ST, SXT | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Durango Pulley Assembly Part Number: 5135971AA
Product Specifications
- Other Name: Pulley Kit - A/C Compressor; A/C Compressor Clutch Pulley; Serpentine Belt Drive Kit; Clutch; Pulley Hub Kit A/C Compressor; A/C Compressor Clutch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2008 Dodge Durango | Adventurer, Limited, SLT, ST, SXT | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Durango Clutch & Pulley Part Number: 5072658AA
Product Specifications
- Other Name: Clutch - A/C Compressor; A/C Compressor Clutch; Clutch Coil; Clutch; Clutch A/C Compressor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2003 Dodge Durango | R/T, SLT, SLT Plus, SXT, Sport | 8 Cyl 5.9 L GAS
View related parts
Dodge Durango Clutch & Pulley Part Number: 5016126AA
Product Specifications
- Other Name: Clutch - A/C Compressor; A/C Compressor Clutch; Clutch; Compressor; Clutch A/C Compressor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004, 2000-2001 Dodge Durango | Base, Limited, SLT, SLT Plus, ST, Sport | 8 Cyl 4.7 L GAS
View related parts
Dodge Durango Clutch & Pulley Part Number: 4882008
Product Specifications
- Other Name: Clutch - A/C Compressor; A/C Compressor Clutch; Clutch Coil; Clutch; Clutch A/C Compressor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2001 Dodge Durango | Base, R/T, SLT, SLT Plus, Sport | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS

Dodge Durango A/C Compressor Clutch

Choose OEM A/C Compressor Clutch that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each A/C Compressor Clutch follows strict manufacturing steps to lock in quality and fit. If your Dodge Durango matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Durango parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Dodge Durango A/C Compressor Clutch Parts and Q&A

Pulley Assembly
5135993AA
Q:
How to Properly Burnish a New A/C Compressor Clutch on Dodge Durango?
A:
Switch the A/C on for 5 seconds, switch it off for 5 seconds and do this for approximately 20 times after you've installed the new clutch. Place the A/C-heater controls in the A/C Recirculation Mode, set the Blower Motor at its highest level and drive the engine so that it goes between 1500 and 2000 rpm. By burnishing, the two contacting surfaces will remain held firmly and the compressor clutch torque will improve.
Clutch Coil
5003681AA
Q:
How to Service an A/C Compressor Clutch Assembly on Dodge Durango?
A:
Before working on the clutch assembly, depart the negative battery cable from the terminal. Take off the air intake hose from both the air filter housing and the resonator, drain a little of the coolant and take out the upper Radiator hose from the radiator and set it where it will not get in your way. After that, take out the radiator fan and its shroud and then the Serpentine Belt. Take the engine wire harness out of the connector on the compressor clutch field coil at the top of your A/C compressor. Carefully pull the compressor clutch field coil connection and wire lead off the bracket. Hold the clutch plate from rotating and remove the bolt using either a band-type oil filter wrench or strap wrench. Don't pry between the clutch plate and the pulley and bearing assembly to avoid damaging the clutch plate and try not to drop any clutch shims so you can reuse them during installation. Tap gently on the clutch plate with the plastic mallet to make it slide out of the compressor shaft and then remove both the clutch plate and shim. With Snap Ring Pliers 9764 or similar, remove the snap ring that holds the pulley and bearing assembly onto the A/C compressor front and then remove the assembly. Last, use Snap Ring Pliers 9764 or the similar tool to get the snap ring out and remove the front field coil of the A/C compressor.