How to remove and install the front Bumper Cover on the JR-41 (Sedan) on Dodge Stratus?

Begin the hood latch release and open the hood to remove the front bumper fascia of the JR-41 (Sedan). After that, unfasten the fascia from the front splash shields using fasteners. Hoist and support the vehicle on safety stands, using appropriate hoisting and jacking procedures. If required, take out the inner wheelhouse front wheelhouse splash shield to access the nut fastening the fender to the fascia wings. After that, take out the fasteners that you can find at the top of the fascia that secure it to the upper crossmember. Next, remove the fasteners that are at the bottom of the fascia that secure it to the radiator closure panel and brake ducts. Detach the screws holding the fascia in place to the front fenders, slide the fascia forward to disengage the hooks at the bottom of the fender, then remove the fascia. If equipped, disconnect the fog lamp wire connector from the body harness. During installation, ensure that the block of energy management foam is positioned in the front fascia. If applicable, connect the fog lamp wire connector to the body wire harness. Place the fascia on the vehicle. Place the fasteners that attach the fascia to the front fenders. Then, place the fasteners that attach the bottom of the fascia to the radiator closure panel and brake ducts. Finish with the fasteners that attach the top of the fascia to the upper crossmember. Last step is to install the splash shields on the front wheelhouse.

How to remove and install the rear Bumper Cover on a JR-41 Sedan on Dodge Stratus?

To remove the rear bumper cover on a JR-41 Sedan, first release the decklid latch and open the decklid. Next, remove the left rear tail lamp and disconnect the license plate wire connector from the tail lamp. Peel back the trunk carpeting at the tail lamps and remove the nut and washer from the fascia to the quarter panel bracket, discarding them afterward. Remove the push-in fasteners that attach the decklid slam bumpers to the top of the fascia, followed by the push-in fastener that connects the center of the fascia to the rear closure panel. Then, remove the screws that attach the fascia to the rear wheelhouse splash shields and the screws that connect the fascia to the quarter panel at the wheelhouse opening. Slide the fascia rearward to disengage the hooks holding it to the bottom of the quarter panel and then remove the fascia from the vehicle. For installation, ensure the energy management foam is properly installed in the rear fascia before positioning it on the vehicle. Slide the fascia forward to engage the hooks to the bottom of the quarter panel, then install the push-in fastener that attaches the center of the fascia to the rear closure panel. Next, install the push-in fasteners for the decklid slam bumpers to the top of the fascia, followed by a new nut and washer to the fascia to quarter panel bracket located in the trunk area. Install the screws that attach the fascia to the quarter panel at the wheelhouse opening and the fasteners for the rear wheelhouse splash shields. Finally, reconnect the license plate wire connector to the left tail lamp and install the tail lamps.

OEM Dodge Stratus Bumper Cover

Bumper Shell

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Bumper Covers found

View related parts
Dodge Stratus Bumper Cover, Rear Part Number: MR516341
$90.89 MSRP: $115.22
You Save: $24.33 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fascia; Bumper Cover, Rear; Bumper Fascia Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2002 Dodge Stratus | R/T, SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Bumper Cover, Front Part Number: 4883009
$537.01 MSRP: $782.00
You Save: $244.99 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Fascia - Front; Fascia Front Primed
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Stratus | Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Stratus Bumper Cover, Front Part Number: 4883008
$537.01 MSRP: $782.00
You Save: $244.99 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Fascia - Front; Fascia Front Primed
- Position: Front
- Replaces: 4778377
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Stratus | Base, ES, SE | 2.0L L4, 2.4L L4, 2.5L V6, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Stratus Bumper Cover, Front Part Number: MR516339
$372.84 MSRP: $472.64
You Save: $99.80 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fascia; Bumper Cover, Front; Bumper Fascia Front
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2002 Dodge Stratus | R/T, SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Bumper Cover Part Number: 4695148
Product Specifications
- Other Name: Cup - Jounce Bumper Stop; Cup; Cup Shock Absorber Stop; Cup, Jounce Bumper
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Stratus | Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Stratus Bumper Cover, Rear Part Number: MR990731
Product Specifications
- Other Name: Fascia - Rear Bumper; Bumper Cover, Rear; Face Rear Bumper
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2005 Dodge Stratus | R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Bumper Cover, Front Part Number: MR990729
Product Specifications
- Other Name: Fascia - Front Bumper; Bumper Cover, Front; Face Front Bumper
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2005 Dodge Stratus | R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Bumper Cover, Black, Front Part Number: MR511999
Product Specifications
- Other Name: Cover - Fascia; Jack Plug Cover, Front; Cover Fascia Black; Cover Fascia
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2002 Dodge Stratus | R/T, SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Bumper Cover, Rear Part Number: 5152058AB
Product Specifications
- Other Name: Fascia - Rear; Bumper Cover, Rear; Fascia Rear Primed
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006 Dodge Stratus | R/T, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Bumper Cover, Front Part Number: 5152053AA
Product Specifications
- Other Name: Fascia - Front; Bumper Cover, Front; Fascia Front Primed
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006 Dodge Stratus | R/T, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Bumper Cover, Front Part Number: 4805381AA
Product Specifications
- Other Name: Fascia Front; Fascia Front Primed
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2000 Dodge Stratus | Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Stratus Bumper Cover, Front Part Number: 4805379AA
Product Specifications
- Other Name: Fascia - Front; Fascia Front Primed
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2000 Dodge Stratus | Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Stratus Bumper Cover, Front Part Number: 4805251AB
Product Specifications
- Other Name: Fascia - Front; Bumper Cover, Front; Fascia Front Primed
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2003 Dodge Stratus | ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Bumper Cover, Rear Part Number: 5073328AA
Product Specifications
- Other Name: Fascia - Rear; Bumper Cover, Rear; Fascia Rear Primed
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Dodge Stratus | ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Bumper Cover, Front Part Number: 4805250AC
Product Specifications
- Other Name: Fascia - Front; Bumper Cover, Front; Fascia Front Primed
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2003 Dodge Stratus | ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Bumper Cover, Front Part Number: 4805897AB
Product Specifications
- Other Name: Fascia - Front; Bumper Cover, Front; Fascia Front Primed
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2006 Dodge Stratus | ES, R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Bumper Cover, Front Part Number: 4805903AB
Product Specifications
- Other Name: Fascia - Front; Bumper Cover, Front; Fascia Front Primed
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2006 Dodge Stratus | ES, R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Bumper Cover, Rear Part Number: 4883010
Product Specifications
- Other Name: Fascia - Rear; Fascia Rear
- Position: Rear
- Replaces: 4887006
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Stratus | Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS

Dodge Stratus Bumper Cover

Choose OEM Bumper Cover that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Bumper Cover follows strict manufacturing steps to lock in quality and fit. If your Dodge Stratus matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Stratus parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Dodge Stratus Bumper Cover Parts and Q&A

Bumper Cover, Front
4805251AB
Q:
How to remove and install the front Bumper Cover on the JR-41 (Sedan) on Dodge Stratus?
A:
Begin the hood latch release and open the hood to remove the front bumper fascia of the JR-41 (Sedan). After that, unfasten the fascia from the front splash shields using fasteners. Hoist and support the vehicle on safety stands, using appropriate hoisting and jacking procedures. If required, take out the inner wheelhouse front wheelhouse splash shield to access the nut fastening the fender to the fascia wings. After that, take out the fasteners that you can find at the top of the fascia that secure it to the upper crossmember. Next, remove the fasteners that are at the bottom of the fascia that secure it to the radiator closure panel and brake ducts. Detach the screws holding the fascia in place to the front fenders, slide the fascia forward to disengage the hooks at the bottom of the fender, then remove the fascia. If equipped, disconnect the fog lamp wire connector from the body harness. During installation, ensure that the block of energy management foam is positioned in the front fascia. If applicable, connect the fog lamp wire connector to the body wire harness. Place the fascia on the vehicle. Place the fasteners that attach the fascia to the front fenders. Then, place the fasteners that attach the bottom of the fascia to the radiator closure panel and brake ducts. Finish with the fasteners that attach the top of the fascia to the upper crossmember. Last step is to install the splash shields on the front wheelhouse.
Bumper Cover, Rear
MR516341
Q:
How to remove and install the rear Bumper Cover on a JR-41 Sedan on Dodge Stratus?
A:
To remove the rear bumper cover on a JR-41 Sedan, first release the decklid latch and open the decklid. Next, remove the left rear tail lamp and disconnect the license plate wire connector from the tail lamp. Peel back the trunk carpeting at the tail lamps and remove the nut and washer from the fascia to the quarter panel bracket, discarding them afterward. Remove the push-in fasteners that attach the decklid slam bumpers to the top of the fascia, followed by the push-in fastener that connects the center of the fascia to the rear closure panel. Then, remove the screws that attach the fascia to the rear wheelhouse splash shields and the screws that connect the fascia to the quarter panel at the wheelhouse opening. Slide the fascia rearward to disengage the hooks holding it to the bottom of the quarter panel and then remove the fascia from the vehicle. For installation, ensure the energy management foam is properly installed in the rear fascia before positioning it on the vehicle. Slide the fascia forward to engage the hooks to the bottom of the quarter panel, then install the push-in fastener that attaches the center of the fascia to the rear closure panel. Next, install the push-in fasteners for the decklid slam bumpers to the top of the fascia, followed by a new nut and washer to the fascia to quarter panel bracket located in the trunk area. Install the screws that attach the fascia to the quarter panel at the wheelhouse opening and the fasteners for the rear wheelhouse splash shields. Finally, reconnect the license plate wire connector to the left tail lamp and install the tail lamps.