Is Your Seat Belt Enough Protection After an Airbag Deployment on Dodge Viper?

After an air bag deploys in a collision, you should immediately replace the front seat belts and their retractors with integral tensioners, in addition to the tensioning assembly. With front air bag deployment, the tensioner will do this simultaneously and must be swapped out. The bolts joining the seat belt retractor to the seat should be replaced after each installation, to avoid the seat latch pins not lining up properly. Review the shoulder/lap belt for rips, frayed parts or signs of wear and swap the retractor when required. The nut that keeps the seat back straight and that the center seat belt attaches to, needs to be properly tightened. Whenever there has been a frontal impact or the air bag went off, all seat belts should be checked for damage and those that show any wear must be replaced. Also, check Lower Anchors and Tether for Children (LATCH) child restraint anchors for any damage and replace them when necessary. During any child restraint anchor service, ensure all hardware, straps and anchors are set up properly and inspect for any damage; replacing a damaged child restraint anchor with the seat assembly helps avoid injury. Seat belt components should always be replaced, rather than attempted to be repaired. If replacement is needed for the front passenger seat cushion, on vehicles with the Occupant Classification System, the seat cushion must be replaced as a complete pack with the frame, springs, pad, seat weight bladder, pressure sensor, foam, wiring and a calibrated OCM. All the existing parts must be discarded and replaced together as a group and none should be split or reused. You should never change out both modules at once; if one of them needs to be replaced, verify the system and then replace the other to prevent loss of information in the calibration codes. Swapping them out at the same time will cause permanent faults in both modems.

OEM Dodge Viper Seat Belt

Seat Safety Belt

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Seat Belts found

View related parts
Dodge Viper Buckle End, Front Part Number: 1YW78DX9AC
$154.09 MSRP: $228.00
You Save: $73.91 (33%)
ADD TO CART
Product Specifications
- Other Name: Seat Belt - Buckle Half; Seat Belt Receptacle, Front; Latch; Seat Belt Buckle Half
- Position: Front
- Replaces: 1YW78YSAAB, 1YW78DX9AB, 1YW78DX9AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2017 Dodge Viper | ACR, Base, GT, GTC, GTS | 10 Cyl 8.4 L GAS, 8.4L V10
View related parts
Dodge Viper Extension Part Number: 5086227AA
$40.72 MSRP: $58.50
You Save: $17.78 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Extender - Seat Belt; Seat Belt Extension; Extender Seat Belt Right Or Left; Extender Seat Belt
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2004 Dodge Viper | SRT-10 | 10 Cyl 8.3 L GAS
View related parts
Dodge Viper Lap & Shoulder Belt, Beige / Black / Red, Front Driver Side Part Number: 1WA311R4AA
$227.73 MSRP: $282.00
You Save: $54.27 (20%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seat Belt - Front; Seat Belt Lap and Shoulder Belt, Front Left; Belt & Retractor; Seat Belt Front
- Position: Front Driver Side
- Replaces: 1WA311RRAA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2017 Dodge Viper | ACR, Base, GT, GTC, GTS | 10 Cyl 8.4 L GAS
View related parts
Dodge Viper Lap & Shoulder Belt, Front Passenger Side Part Number: UB641X9AD
$54.55 MSRP: $92.20
You Save: $37.65 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seat Belt - Front; Seat Belt Lap and Shoulder Belt, Right; Belt & Retractor
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Dodge Viper | SRT-10 | 10 Cyl 8.3 L GAS
View related parts
Dodge Viper Swivel Joint, Driver Side Part Number: 5029127AD
$36.25 MSRP: $52.10
You Save: $15.85 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Loop - Seat Belt; Seat Belt Guide, Front Left, Left; Turning Loop Seat Belt
- Position: Driver Side
- Replaces: 5029127AC, 5029127AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2017 Dodge Viper
- 2008-2010 Dodge Viper | 8.4L V10
- 2003-2006 Dodge Viper | 8.3L V10
View More
View related parts
Dodge Viper Lap & Shoulder Belt, Front Driver Side Part Number: UB651X9AD
$145.95 MSRP: $195.00
You Save: $49.05 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seat Belt - Front; Seat Belt Lap and Shoulder Belt, Left; Belt & Retractor
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Dodge Viper | SRT-10 | 10 Cyl 8.3 L GAS
View related parts
Dodge Viper Lap & Shoulder Belt, Front Driver Side Part Number: UB651X9AF
$125.17 MSRP: $165.00
You Save: $39.83 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seatbelt - Front; Seat Belt Lap and Shoulder Belt, Left; Belt & Retractor; Seat Belt Front
- Position: Front Driver Side
- Replaces: UB651X9AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Viper
- 2004-2006 Dodge Viper | 8.3L V10
View related parts
Dodge Viper Buckle End Part Number: TQ881X9AB
$28.54 MSRP: $36.17
You Save: $7.63 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seat Belt - Buckle Half; Seat Belt Receptacle; Latch; Seat Belt Buckle Half
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Dodge Viper | SRT-10 | 10 Cyl 8.3 L GAS
View related parts
Dodge Viper Door Striker Part Number: 4763550
$2.45 MSRP: $3.10
You Save: $0.65 (21%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seat Belt - Lower Door Restraint System; Interlock, Lower Door Restraint
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-1996 Dodge Viper | Base, GTS | 10 Cyl 8.0 L GAS
View related parts
Dodge Viper Lap & Shoulder Belt, Beige / Black / Red, Front Driver Side Part Number: 1WA321R4AB
$250.39 MSRP: $307.00
You Save: $56.61 (19%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seat Belt - Front; Seat Belt Lap and Shoulder Belt, Front Left, Front Right; Belt & Retractor; Seat Belt Front
- Position: Front Driver Side
- Replaces: 1WA321RRAA, 1WA321R4AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2017 Dodge Viper | ACR, Base, GT, GTC, GTS | 10 Cyl 8.4 L GAS
- 2013 Dodge Viper | 8.4L V10
View related parts
Dodge Viper Belt & Retractor Part Number: HV60LX9
$92.69 MSRP: $107.00
You Save: $14.31 (14%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt - Front Seat Lap/Shoulder - Right; Seat Belt, Lap And Shoulder Door Mounting
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992 Dodge Viper | Base | 10 Cyl 8.0 L GAS
View related parts
Dodge Viper Belt & Retractor Part Number: HC77MX9
Product Specifications
- Other Name: Belt - Front Seat Lap/Shoulder - Left; Seat Belt, Lap And Shoulder Door Mounting
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1993-1996 Dodge Viper | Base, GTS | 10 Cyl 8.0 L GAS
View related parts
Dodge Viper Belt & Retractor, Front Outer Part Number: HC68MX9
Product Specifications
- Other Name: Seat Belt - Front Outer; Seat Belt, Lap And Shoulder Door Mounting
- Position: Front Outer
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1993-1996 Dodge Viper | Base, GTS | 10 Cyl 8.0 L GAS
View related parts
Dodge Viper Buckle End Part Number: 4848719AB
Product Specifications
- Other Name: Seat Belt - Buckle Half; Latch; Seat Belt Buckle Half
- Replaces: 4848719
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-2002 Dodge Viper | ACR, GT2, GTS, R/T-10 | 10 Cyl 8.0 L GAS, 8.0L V10
View related parts
Dodge Viper Swivel Joint, Front Passenger Side Part Number: 5029126AD
Product Specifications
- Other Name: Loop - Seat Belt; Seat Belt Guide, Front Right, Right; Turning Loop Seat Belt
- Position: Front Passenger Side
- Replaces: 5029126AC, 5029126AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2017 Dodge Viper
- 2008-2010 Dodge Viper | 8.4L V10
- 2003-2006 Dodge Viper | 8.3L V10
View More
View related parts
Dodge Viper Buckle End Part Number: TQ881X9AC
Product Specifications
- Other Name: Seat Belt - Buckle Half; Seat Belt Receptacle; Buckle; Latch; Seat Belt Buckle Half
- Replaces: XN611X9AA, XN611BNAA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Viper
- 2003-2006 Dodge Viper | 8.3L V10
View related parts
Dodge Viper Buckle End, Black Part Number: 4848718
Product Specifications
- Other Name: Seat Belt - Buckle Half; Latch; Buckle, Seat Belt Inner (Black); Seat Belt Buckle Half
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2002 Dodge Viper | ACR, GT2, GTS, R/T-10 | 10 Cyl 8.0 L GAS
View related parts
Dodge Viper Belt & Retractor, Front Outer Part Number: HV61LX9
Product Specifications
- Other Name: Seat Belt - Front Outer; Seat Belt, Lap And Shoulder Door Mounting
- Position: Front Outer
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992 Dodge Viper | Base | 10 Cyl 8.0 L GAS
View related parts
Dodge Viper Lap & Shoulder Belt, Front Part Number: MB861X9AB
Product Specifications
- Other Name: Seat Belt - Front; Belt & Retractor
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2002 Dodge Viper | ACR, GT2, GTS, R/T-10 | 10 Cyl 8.0 L GAS
View related parts
Dodge Viper Lap & Shoulder Belt, Front Passenger Side Part Number: 1BD961X9AA
Product Specifications
- Other Name: Seat Belt - Front; Seat Belt Lap and Shoulder Belt, Right; Belt & Retractor; Seat Belt Front
- Position: Front Passenger Side
- Replaces: UB641X9AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Viper
- 2004-2006 Dodge Viper | 8.3L V10

Dodge Viper Seat Belt

Choose OEM Seat Belt that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Seat Belt follows strict manufacturing steps to lock in quality and fit. If your Dodge Viper matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Viper parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Dodge Viper Seat Belt Parts and Q&A

Extension
5086227AA
Q: Is Your Seat Belt Enough Protection After an Airbag Deployment on Dodge Viper?
A:
After an Air Bag deploys in a collision, you should immediately replace the front seat belts and their retractors with integral tensioners, in addition to the tensioning assembly. With front air bag deployment, the tensioner will do this simultaneously and must be swapped out. The bolts joining the seat belt retractor to the seat should be replaced after each installation, to avoid the seat latch pins not lining up properly. Review the shoulder/lap belt for rips, frayed parts or signs of wear and swap the retractor when required. The nut that keeps the seat back straight and that the center seat belt attaches to, needs to be properly tightened. Whenever there has been a frontal impact or the air bag went off, all seat belts should be checked for damage and those that show any wear must be replaced. Also, check Lower Anchors and Tether for Children (LATCH) child restraint anchors for any damage and replace them when necessary. During any child restraint anchor service, ensure all hardware, straps and anchors are set up properly and inspect for any damage; replacing a damaged child restraint anchor with the seat assembly helps avoid injury. Seat belt components should always be replaced, rather than attempted to be repaired. If replacement is needed for the front passenger Seat Cushion, on vehicles with the Occupant Classification System, the seat cushion must be replaced as a complete pack with the frame, springs, pad, seat weight bladder, pressure sensor, foam, wiring and a calibrated OCM. All the existing parts must be discarded and replaced together as a group and none should be split or reused. You should never change out both modules at once; if one of them needs to be replaced, verify the system and then replace the other to prevent loss of information in the calibration codes. Swapping them out at the same time will cause permanent faults in both modems.