How to Service and Repair a Turn Signal Switch on Jeep Cherokee?

To service and repair the turn signal switch, first disconnect and isolate the battery negative cable. Remove the knee blocker from the instrument panel. Next, remove the three screws securing the lower steering column shroud to the upper shroud. For vehicles with a standard non-tilt steering column, loosen the two upper steering column mounting nuts; for those with a tilt steering column, move it to the fully lowered position. Remove both the upper and lower shrouds from the steering column. Then, remove the two screws that secure the multi-function switch water shield and bracket to the top of the steering column, followed by the one screw located below the multi-function switch control stalk. Gently pull the lower mounting tab of the multi-function switch water shield bracket away from the steering column to clear the screw boss below the control stalk. Lift the water shield and bracket with the multi-function switch off the left side of the steering column to access the two wire harness connectors. Disconnect the two instrument panel wire harness connectors from the multi-function switch connector receptacles and remove the multi-function switch and water shield as a unit. For installation, carefully install the water shield onto the switch, then position the multi-function switch and water shield near their mounts on the steering column. Reconnect the two instrument panel wire harness connectors to the multi-function switch connector receptacles and position the multi-function switch onto its mounts on the left side of the steering column. Ensure the lower mounting tab of the multi-function switch water shield bracket is positioned to the steering column screw boss below the control stalk, then install and tighten the screw below the control stalk to 1.1 Nm (10 in. lbs.). Install and tighten the two screws securing the multi-function switch water shield and bracket to the top of the steering column to 2.2 Nm (20 in. lbs.). Position both the upper and lower shrouds onto the steering column and install and tighten the three screws securing the lower shroud to the upper shroud to 2 Nm (18 in. lbs.). If applicable, tighten the two nuts securing the non-tilt steering column upper mounting bracket to the dash panel steering column support bracket studs to 22 Nm (200 in. lbs.). Finally, install the knee blocker onto the instrument panel and reconnect the battery negative cable.

OEM Jeep Cherokee Turn Signal Switch

Turn Signal Indicator Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Turn Signal Switches found

View related parts
Jeep Cherokee Multifunction Switch Part Number: 68455814AA
$417.93 MSRP: $611.00
You Save: $193.07 (32%)
ADD TO CART
Product Specifications
- Other Name: Module - Steering Column; Turn Signal & Combination Lever; Combination Switch; Air Bag Clockspring; Clockspring; Module Steering Column Includes Clockspring; Module Steering Column
- Replaces: 68141121AH, 68141121AL, 68141121AC, 68141121AM, 68141121AD, 68141121AE, 68141121AG, 68375484AA, 68141121AB, 68141121AF, 68141121AJ, 68141121AI, 68141121AK, 68375484AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Jeep Cherokee | 75th Anniversary, 80th Anniversary, Altitude, Altitude Lux, High Altitude, Latitude, Latitude Lux, Latitude Plus, Limited, Overland, Sport, Trailhawk, Trailhawk Elite, Upland, X | 2.0L L4, 2.4L L4, 3.2L V6, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
View related parts
Jeep Cherokee Multifunction Switch Part Number: 68455810AA
$431.67 MSRP: $629.00
You Save: $197.33 (32%)
ADD TO CART
Product Specifications
- Other Name: Module - Steering Column; Turn Signal & Combination Lever; Combination Switch; Air Bag Clockspring; Clockspring; Module Steering Column Includes Clockspring; Module Steering Column
- Replaces: 68141120AI, 68375477AA, 68141120AB, 68141120AJ, 68375477AB, 68141120AF, 68141120AC, 68141120AK, 68141120AH, 68141120AL, 68141120AG, 68141120AM, 68141120AE, 68141120AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Jeep Cherokee | 75th Anniversary, 80th Anniversary, Altitude, Altitude Lux, High Altitude, Latitude, Latitude Lux, Latitude Plus, Limited, Overland, Sport, Trailhawk, Trailhawk Elite, Upland, X | 2.0L L4, 2.4L L4, 3.2L V6, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
View related parts
Jeep Cherokee Turn Signal Switch Part Number: 56010315AA
Product Specifications
- Other Name: Switch - Multifunction; Multi Purpose Switch; Signal Switch; Multifunction Left Stalk for Interior/Exterior Lights & Turn Signal Controls.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2001 Jeep Cherokee | Classic, Country, Limited, SE, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Ignition Switch Part Number: 4728424
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Housing; Windshield Washer Switch.; Turn Signal Switch; Multifunction, Wiper, Headlamp Dimmer, Hazard, Signal & Tilt options.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1996 Jeep Cherokee | Classic, Country, SE, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Turn Signal Switch Part Number: 56007255
Product Specifications
- Other Name: Switch - Turn Signal; Multi Purpose Switch; Signal Switch; Switch; Switch Assembly, Directional Signal; Switch, Turn Signal
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1995 Jeep Cherokee | Country, SE, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Turn Signal Switch Part Number: 56002011
Product Specifications
- Other Name: Switch - Turn Signal; Hazard Flasher Switch; Multi Purpose Switch; Signal Switch; Turn Signal & Hazard Switch; Switch, Directional; Switch, Turn Signal; Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-1993 Jeep Cherokee | Base, Briarwood, Chief, Country, Laredo, Limited, Pioneer, Sport | 4 Cyl 2.1 L DIESEL, 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Turn Signal Switch Part Number: 4778760
Product Specifications
- Other Name: Switch - Multifunction; Steering Column Switch Housing; Multi Purpose Switch; Combination Switch; Multi-Function Turn Signal & Wiper; Headlamp Dimmer; Signal & Hazard Switch.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1996 Jeep Cherokee | Classic, Country, SE, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Turn Signal Switch, Lower Part Number: 4778424
Product Specifications
- Other Name: Housing - A/C And Heater Lower; Multi Purpose Switch; Lower Housing; Housing A/C And Heater Lower; Housing, Lower
- Position: Lower
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996 Jeep Cherokee | Classic, Country, SE, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS

Jeep Cherokee Turn Signal Switch

Choose OEM Turn Signal Switch that meet Jeep factory standards. Jeep designs and tests every component for precision and durability. Each Turn Signal Switch follows strict manufacturing steps to lock in quality and fit. If your Jeep Cherokee matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Cherokee parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Jeep Cherokee Turn Signal Switch activates the external light indicators to let other drivers know in which direction the driver intends to turn. The lever component is mounted within the steering column. When the Turn Signal Switch is moved up or down, it closes a circuit that powers the left or right signal bulb. The internal contacts of Turn Signal Switches also incorporate dials and buttons that can initiate windshield wipers, fog lights, headlights, and cruise control, combining various lighting and convenience controls into one device. Due to the importance of the lighting system in ongoing safe traffic and also after dark and in bad weather, a good Turn Signal Switch ensures clear communication and predictable action from a vehicle. The right year, make, and model means the Turn Signal Switch will fit the steering column wiring and mounting points on a Jeep Cherokee. Retaining this functionality guarantees that every Jeep Cherokee is visible and comprehensible to other road users. This is what makes the Jeep Cherokee Turn Signal Switch so useful.

Jeep Cherokee Turn Signal Switch Parts and Q&A

Turn Signal Switch
56010315AA
Q: How to Service and Repair a Turn Signal Switch on Jeep Cherokee?
A:
To service and repair the turn signal switch, first disconnect and isolate the battery negative cable. Remove the knee blocker from the instrument panel. Next, remove the three screws securing the lower steering column shroud to the upper shroud. For vehicles with a standard non-tilt steering column, loosen the two upper steering column mounting nuts; for those with a tilt steering column, move it to the fully lowered position. Remove both the upper and lower shrouds from the steering column. Then, remove the two screws that secure the multi-function switch water shield and bracket to the top of the steering column, followed by the one screw located below the multi-function switch control stalk. Gently pull the lower mounting tab of the multi-function switch water shield bracket away from the steering column to clear the screw boss below the control stalk. Lift the water shield and bracket with the multi-function switch off the left side of the steering column to access the two wire harness connectors. Disconnect the two instrument panel wire harness connectors from the multi-function switch connector receptacles and remove the multi-function switch and water shield as a unit. For installation, carefully install the water shield onto the switch, then position the multi-function switch and water shield near their mounts on the steering column. Reconnect the two instrument panel wire harness connectors to the multi-function switch connector receptacles and position the multi-function switch onto its mounts on the left side of the steering column. Ensure the lower mounting tab of the multi-function switch water shield bracket is positioned to the steering column screw boss below the control stalk, then install and tighten the screw below the control stalk to 1.1 Nm (10 in. lbs.). Install and tighten the two screws securing the multi-function switch water shield and bracket to the top of the steering column to 2.2 Nm (20 in. lbs.). Position both the upper and lower shrouds onto the steering column and install and tighten the three screws securing the lower shroud to the upper shroud to 2 Nm (18 in. lbs.). If applicable, tighten the two nuts securing the non-tilt steering column upper mounting bracket to the dash panel steering column support bracket studs to 22 Nm (200 in. lbs.). Finally, install the knee blocker onto the instrument panel and reconnect the battery negative cable.