How to Service and Repair an Exhaust Manifold on Jeep Commander?

You should begin the service or repair of the exhaust manifold by removing the negative cable from the battery. Lift and prop the vehicle and then take out the bolts and nuts connecting the exhaust pipe to the engine manifold. After you've lowered the car, carefully take out the exhaust heat shield. After that, extract the bolts, nuts and washers holding the manifold to the cylinder head and remove the manifold and its gasket from the cylinder head. It's done the same way for both the right and left exhaust manifolds.

How to Maintain the Left Exhaust Manifold on Jeep Commander?

In order to access the left exhaust manifold, first unconnect the negative battery cable and lift the vehicle. After detaching the exhaust pipe's bolts and nuts, reduce the vehicle to the ground. After that, take out the exhaust heat shields and undo the bolts, nuts and washers that connect the manifold to the cylinder head and finish by removing the manifold and gasket. During the installation of the new manifold, if the studs came free, apply sealer to the ends with the rough threads to make sure water does not leak. Put the exhaust manifold and the gasket on the studs of the cylinder head, then add conical washers and nuts to these studs. Attach the remaining conical washers and use a torque wrench to tighten the bolts and nuts at 25 Nm (18 ft. lbs.). Start from the center arm and repeat this along the entire system from the inside outward. Reglue the exhaust heat shields into position, but do not tighten their bolts too hard to not damage them. Join the exhaust pipe to the manifold and attach it by using bolts, nuts and retainers until you reach 34 Nm (25 ft. lbs.) of torque.

OEM Jeep Commander Exhaust Manifold

Engine Exhaust Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Exhaust Manifolds found

View related parts
Jeep Commander Exhaust Manifold, Driver Side Part Number: 53013599AB
$143.74 MSRP: $216.00
You Save: $72.26 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left; Manifold; Manifold Exhaust
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Jeep Commander | 65th Anniversary Edition, Base, Limited, Sport | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Jeep Commander Exhaust Manifold, Passenger Side Part Number: 53013858AD
$189.21 MSRP: $279.00
You Save: $89.79 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right; Manifold; Manifold Exhaust
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Jeep Commander | Limited, Overland, Sport | 8 Cyl 5.7 L GAS
View related parts
Jeep Commander Exhaust Manifold, Passenger Side Part Number: 53013692AB
$261.72 MSRP: $387.00
You Save: $125.28 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right; Manifold; Manifold Exhaust
- Position: Passenger Side
- Replaces: 53013692AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2010 Jeep Commander | 65th Anniversary Edition, Base, Sport | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Jeep Commander Exhaust Manifold, Driver Side Part Number: 53013691AC
$266.26 MSRP: $396.00
You Save: $129.74 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left; Manifold; Manifold Exhaust
- Position: Driver Side
- Replaces: 53013691AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2010 Jeep Commander | 65th Anniversary Edition, Base, Sport | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Jeep Commander Exhaust Manifold, Passenger Side Part Number: 53013598AB
$151.73 MSRP: $200.00
You Save: $48.27 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right; Manifold; Manifold Exhaust
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Jeep Commander | 65th Anniversary Edition, Base, Limited, Sport | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Jeep Commander Exhaust Manifold, Driver Side Part Number: 53013605AB
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left; Exhaust Manifold Gasket; Manifold Gasket; Manifold; Manifold Exhaust Reference Refer To 820 Exhaust Manifolds; Manifold Exhaust
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2008 Jeep Commander | Limited, Overland | 8 Cyl 5.7 L GAS
View related parts
Jeep Commander Exhaust Manifold, Driver Side Part Number: 53013857AD
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left; Manifold; Manifold Exhaust
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Jeep Commander | Limited, Overland, Sport | 8 Cyl 5.7 L GAS
View related parts
Jeep Commander Exhaust Manifold, Driver Side Part Number: 53013793AE
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Left; Manifold; Manifold Exhaust
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2009 Jeep Commander | Limited, Sport | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Jeep Commander Exhaust Manifold, Passenger Side Part Number: 53013792AE
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right; Manifold; Manifold Exhaust
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2009 Jeep Commander | Limited, Sport | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Jeep Commander Exhaust Manifold, Passenger Side Part Number: 53013606AB
Product Specifications
- Other Name: Manifold - Exhaust; Exhaust Manifold, Right; Manifold; Manifold Exhaust Reference Refer To 820 Exhaust Manifolds; Manifold Exhaust
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2008 Jeep Commander | Limited, Overland | 8 Cyl 5.7 L GAS

Jeep Commander Exhaust Manifold

Choose OEM Exhaust Manifold that meet Jeep factory standards. Jeep designs and tests every component for precision and durability. Each Exhaust Manifold follows strict manufacturing steps to lock in quality and fit. If your Jeep Commander matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Commander parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Jeep Commander Exhaust Manifold is proven to be an important part that boosts the performance and durability of Jeep Commander vehicles. As a component of a vehicle's exhaust system, the Exhaust Manifold is strategically positioned to safely and effectively channel hot exhaust gases produced by the engine toward the exhaust system, contributing to the engine's efficiency as well as reducing the quantity of hazardous emissions that goes into the atmosphere. Traditionally, the ball is of a heavy construction and can be made of cast iron or stainless steel and it is quite reliable to be used in Jeep because it does not corrode easily. The Jeep Commander is a vehicle that comes in different models, which ranges from the XK and the 2022 Meridian; these models benefit from the construction of the Exhaust Manifold that comprises of several tubes in line with the cylinder number of the engine with the view of aiding gas collection. These increase the performance capacity of the vehicle and at the same time, minimize the chances of having leaks from the exhaust system. The Jeep Commander Exhaust Manifold has found its unique position among car parts because it is designed for V6 and V8 engines to guarantee comfortable and high performing driving. Moreover, this manifold contributes great to increase the velocity of the exhaust gas which is so valuable for increasing the fuel efficiency, That is why the increasing the exhaust gas velocity is crucial for getting the balance of the power and the economy. In sum, the Jeep Commander Exhaust Manifold reflects upon the reliability and performance that can be associated with Jeep Commander parts and proves that it is one of the key models among Jeep automobiles.

Jeep Commander Exhaust Manifold Parts and Q&A

Exhaust Manifold, Passenger Side
53013598AB
Q: How to Service and Repair an Exhaust Manifold on Jeep Commander?
A:
You should begin the service or repair of the exhaust manifold by removing the negative cable from the battery. Lift and prop the vehicle and then take out the bolts and nuts connecting the exhaust pipe to the engine manifold. After you've lowered the car, carefully take out the exhaust heat shield. After that, extract the bolts, nuts and washers holding the manifold to the cylinder head and remove the manifold and its gasket from the cylinder head. It's done the same way for both the right and left exhaust manifolds.
Exhaust Manifold, Driver Side
53013599AB
Q: How to Maintain the Left Exhaust Manifold on Jeep Commander?
A:
In order to access the left exhaust manifold, first unconnect the negative battery cable and lift the vehicle. After detaching the exhaust pipe's bolts and nuts, reduce the vehicle to the ground. After that, take out the exhaust heat shields and undo the bolts, nuts and washers that connect the manifold to the cylinder head and finish by removing the manifold and gasket. During the installation of the new manifold, if the studs came free, apply sealer to the ends with the rough threads to make sure water does not leak. Put the exhaust manifold and the gasket on the studs of the cylinder head, then add conical washers and nuts to these studs. Attach the remaining conical washers and use a torque wrench to tighten the bolts and nuts at 25 Nm (18 ft. lbs.). Start from the center arm and repeat this along the entire system from the inside outward. Reglue the exhaust heat shields into position, but do not tighten their bolts too hard to not damage them. Join the exhaust pipe to the manifold and attach it by using bolts, nuts and retainers until you reach 34 Nm (25 ft. lbs.) of torque.