How to Install a Liftgate Hinge Without Removing the Liftgate on Jeep Grand Cherokee?

While hinges can be accessed without removing the liftgate, replacement demands one by one. Before installing, smear a layer of body sealer onto the hinge mating surfaces where they connect to the body. Put the body half of the liftgate hinge (1) into place under the upper liftgate opening header on the vehicle. Get access to the area for fitting by gently pulling down the rear edge of the headliner from the header, install the nuts and tighten them, then attach and tighten the other bolt to secure the hinge, all with 28 Nm (21 ft. lbs.). After that, connect the liftgate to its end of the hinge (1) on the car and tighten the two screws (2) that hold it. After that, fit the struts, take away the support from the liftgate and make sure the liftgate opens and closes correctly. Once finished, place the trim plate above the upper liftgate opening header and look for water leaks around the hinge to body screws.

How to Maintain and Fix a Liftgate Hinge on Jeep Grand Cherokee?

To work on the trunk or liftgate hinge, open the liftgate and support it with an appropriate prop or block first. Take off the support struts and trim plate from the lid's upper opening framework. Make a mark on the liftgate inner panel to show where the hinge liftgate half will go. With the two hinge screws out, place a mark on the upper liftgate opening header half way between the body of the hinge and the end of the header. Lift the rear edge of the headliner while pulling the two nuts and one bolt that attach the hinge studs to the header underside. After removing those parts, remove the hinge from the car. First, seal both sides of the hinge to the body with an appropriate sealer. Then, put the upper half of the liftgate hinge onto the vehicle's liftgate header opening. Pull the rear part of the headliner down again so you can tighten two nuts and one bolt holding the hinge to the header. Ensure the fasteners are tightened to 28 N.m (21 ft.lbs.). Set the liftgate at the liftgate side of the hinge and attach it by screwing in the two hinge screws to 28 N.m (21 ft.lbs.). Put in the tailgate struts, remove the support from the liftgate and see if the liftgate opens and closes properly. After that, attach the trim plate to the upper section of the liftgate opening and hold a pressure hose at the hinge to body screws to see if water leaks out.

OEM Jeep Grand Cherokee Liftgate Hinge

Luggage Compartment Door Hinge

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Liftgate Hinges found

View related parts
Jeep Grand Cherokee Hinge, Rear Part Number: 68299174AA
$49.99 MSRP: $101.00
You Save: $51.01 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge - Liftgate; Liftgate Hinge, Rear; Door Hinge; Hinge Liftgate; Liftgate Hinge
- Position: Rear
- Replaces: 55113709AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2021 Jeep Grand Cherokee | 75th Anniversary, 80th Anniversary, Altitude, High Altitude, Laredo, Laredo E, Laredo X, Limited, Limited X, Overland, SRT, Summit, Trackhawk, Trailhawk, Upland | 3.0L V6, 3.6L V6, 5.7L V8, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Grand Cherokee Hinge, Rear Passenger Side Part Number: 5019418AA
$72.29 MSRP: $95.30
You Save: $23.01 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge - Liftglass; Liftgate Glass Hinge, Rear Right; Hinge Liftglass
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999-2004 Jeep Grand Cherokee | Laredo, Limited, Overland, Special Edition, Sport | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
View related parts
Jeep Grand Cherokee Hinge, Rear Driver Side Part Number: 55113563AG
$71.84 MSRP: $102.00
You Save: $30.16 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge - Liftgate; Liftgate Hinge, Rear Left; Door Hinge; Hinge Liftgate; Liftgate Hinge
- Position: Rear Driver Side
- Replaces: 55113563AE, 55113563AB, 55113563AC, 55113563AF, 55113563AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Jeep Grand Cherokee | Laredo, Limited, Overland, Overland Summit, SRT8 | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Grand Cherokee Hinge, Rear Part Number: 68375575AC
$15.95 MSRP: $23.45
You Save: $7.50 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge - Liftgate; Liftgate Hinge, Rear
- Position: Rear
- Replaces: 68375575AA, 68375575AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2022-2025 Jeep Grand Cherokee | 30th Anniversary 4xe, 4xe, Altitude, Altitude X, Anniversary Edition 4xe, Laredo, Laredo X, Limited, Overland, Summit, Summit Reserve, Trailhawk | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS
View related parts
Jeep Grand Cherokee Hinge, Rear Passenger Side Part Number: 55394178AB
$29.75 MSRP: $42.75
You Save: $13.00 (31%)
Product Specifications
- Other Name: Hinge - Liftglass; Liftgate Glass Hinge, Rear Right; Hinge Liftglass
- Position: Rear Passenger Side
- Replaces: 55394178AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2008 Jeep Grand Cherokee | 65th Anniversary Edition, Laredo, Limited, Overland, SRT8 | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Jeep Grand Cherokee Hinge, Rear Driver Side Part Number: 55394179AB
$49.71 MSRP: $71.45
You Save: $21.74 (31%)
Product Specifications
- Other Name: Hinge - Liftglass; Liftgate Glass Hinge, Rear Left; Hinge Liftglass
- Position: Rear Driver Side
- Replaces: 55394179AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2008 Jeep Grand Cherokee | 65th Anniversary Edition, Laredo, Limited, Overland, SRT8 | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Jeep Grand Cherokee Hinge Part Number: 4796432
Product Specifications
- Other Name: Hinge - Liftgate; Liftgate Hinge; Door Hinge; Hinge Liftgate
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1998 Jeep Grand Cherokee | 5.9 Limited, Laredo, Limited, Orvis, SE, TSi | 6 Cyl 4.0 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Jeep Grand Cherokee Hinge, Rear Driver Side Part Number: 5019419AA
Product Specifications
- Other Name: Hinge - Liftglass; Liftgate Glass Hinge, Rear Left; Hinge Liftglass
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999-2004 Jeep Grand Cherokee | Laredo, Limited, Overland, Special Edition, Sport | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
View related parts
Jeep Grand Cherokee Hinge, Rear Passenger Side Part Number: 55113562AG
Product Specifications
- Other Name: Hinge - Liftgate; Liftgate Hinge, Rear Right; Door Hinge; Hinge Liftgate; Liftgate Hinge
- Position: Rear Passenger Side
- Replaces: 55113562AB, 55113562AF, 55113562AE, 55113562AD, 55113562AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Jeep Grand Cherokee | Laredo, Limited, Overland, Overland Summit, SRT8 | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Grand Cherokee Hinge Part Number: 55075163
Product Specifications
- Other Name: Hinge, Assembly, Right; Hinge Liftgate
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1998 Jeep Grand Cherokee | 5.9 Limited, Laredo, Limited, Orvis, SE, TSi | 6 Cyl 4.0 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Jeep Grand Cherokee Hinge Part Number: 55075162
Product Specifications
- Other Name: Hinge, Assembly, Right; Hinge Liftgate
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1998 Jeep Grand Cherokee | 5.9 Limited, Laredo, Limited, Orvis, SE, TSi | 6 Cyl 4.0 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Jeep Grand Cherokee Hinge, Rear Part Number: 55396772AF
Product Specifications
- Other Name: Hinge - Liftgate; Liftgate Hinge, Rear; Door Hinge; Hinge Liftgate; Liftgate Hinge
- Position: Rear
- Replaces: 55396772AC, 55396772AE, 55396772AD, 68024103AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2010 Jeep Grand Cherokee | 65th Anniversary Edition, Laredo, Limited, Overland, SRT8 | 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.7 L GAS, 6.1L V8, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Jeep Grand Cherokee Hinge, Rear Part Number: 4589059AD
Product Specifications
- Other Name: Hinge - Liftgate; Liftgate Hinge, Rear; Door Hinge; Hinge Liftgate; Liftgate Hinge
- Position: Rear
- Replaces: 4589059AA, 4589059AB, 55257015AF, 55257015AC, 4589059AC, 55257015AD, 55257015AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999-2004 Jeep Grand Cherokee | Laredo, Limited, Overland, Special Edition, Sport | 4.0L L6, 4.7L V8, 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS

Jeep Grand Cherokee Liftgate Hinge

Choose OEM Liftgate Hinge that meet Jeep factory standards. Jeep designs and tests every component for precision and durability. Each Liftgate Hinge follows strict manufacturing steps to lock in quality and fit. If your Jeep Grand Cherokee matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Grand Cherokee parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Jeep Grand Cherokee Liftgate Hinge Parts and Q&A

Hinge, Rear Driver Side
55394179AB
Q: How to Install a Liftgate Hinge Without Removing the Liftgate on Jeep Grand Cherokee?
A:
While hinges can be accessed without removing the liftgate, replacement demands one by one. Before installing, smear a layer of body sealer onto the hinge mating surfaces where they connect to the body. Put the body half of the liftgate hinge (1) into place under the upper liftgate opening header on the vehicle. Get access to the area for fitting by gently pulling down the rear edge of the headliner from the header, install the nuts and tighten them, then attach and tighten the other bolt to secure the hinge, all with 28 Nm (21 ft. lbs.). After that, connect the liftgate to its end of the hinge (1) on the car and tighten the two screws (2) that hold it. After that, fit the struts, take away the support from the liftgate and make sure the liftgate opens and closes correctly. Once finished, place the trim plate above the upper liftgate opening header and look for water leaks around the hinge to body screws.
Hinge, Rear Passenger Side
55394178AB
Q: How to Maintain and Fix a Liftgate Hinge on Jeep Grand Cherokee?
A:
To work on the trunk or liftgate hinge, open the liftgate and support it with an appropriate prop or block first. Take off the support struts and trim plate from the lid's upper opening framework. Make a mark on the liftgate inner panel to show where the hinge liftgate half will go. With the two hinge screws out, place a mark on the upper liftgate opening header half way between the body of the hinge and the end of the header. Lift the rear edge of the headliner while pulling the two nuts and one bolt that attach the hinge studs to the header underside. After removing those parts, remove the hinge from the car. First, seal both sides of the hinge to the body with an appropriate sealer. Then, put the upper half of the liftgate hinge onto the vehicle's liftgate header opening. Pull the rear part of the headliner down again so you can tighten two nuts and one bolt holding the hinge to the header. Ensure the fasteners are tightened to 28 N.m (21 ft.lbs.). Set the liftgate at the liftgate side of the hinge and attach it by screwing in the two hinge screws to 28 N.m (21 ft.lbs.). Put in the tailgate struts, remove the support from the liftgate and see if the liftgate opens and closes properly. After that, attach the trim plate to the upper section of the liftgate opening and hold a pressure hose at the hinge to body screws to see if water leaks out.