How to service the front Output Shaft Seal on Jeep Wrangler?

To carry out service on the front output shaft seal, you will first need to raise the vehicle followed by the removal of front propeller shaft. Next, remove the front output shaft yoke. Use a prying tool to separate the seal from the front case. For installation, place a new front output seal on Installer Tool 8143-A so that the garter spring on the seal face into the case. Using a hammer, start to tap the seal into the bore then continue tapping until the installer tool seats against the case.

How can the rear Output Shaft Seal be removed and installed on Jeep Wrangler?

To remove the rear output shaft seal, first shift the transmission and transfer case into Neutral, then raise and support the vehicle. Mark a line across the pinion shaft and at each end of the propeller shaft for installation reference. Remove the U-joint strap bolts at the pinion shaft yoke and pry open the clamp holding the dust boot to the propeller shaft yoke. Slide the slip yoke off the transmission/transfer case output shaft and remove the propeller shaft. Spread the band clamp holding the output shaft boot to the output shaft slinger or output shaft damper with a suitable awl. Remove the output shaft boot from the slinger or output shaft damper. If the vehicle lacks an output shaft damper, use Puller MD-998056-A to remove the output shaft rear slinger. If equipped with an output shaft damper, use Screws 8421 along with the puller yoke and forcing screw from a bolt-grip puller set to remove the transfer case output shaft damper. Use a suitable pry tool or a slide hammer mounted screw to remove the seal from the rear retainer. For installation, apply a liberal quantity of petroleum jelly to the new rear seal and the output shaft to protect the seal lips during installation. Slide the seal onto Seal Protector 6992 and then onto the output shaft. Use Installer C-4076-B with Handle MD-998323 to drive the seal into the rear bearing retainer. If the vehicle is not equipped with an output shaft damper, install a new output shaft rear slinger with Installer 8408. For vehicles with an output shaft damper, position the damper weight on the output shaft, ensuring it is square to the shaft, then use Installer 8422 to properly position the damper. Install the boot on the output shaft slinger or output shaft damper and crimp the retaining clamp with tool C-4975-A. Slide the slip yoke onto the transmission/transfer case output shaft, align the installation reference marks at the axle yoke, and install the propeller shaft. Tighten the U-joint strap/clamp bolts at the axle yoke to 19 Nm (14 ft. lbs.) and crimp the clamp with Clamp Tool C-4975A to secure the dust boot to the propeller shaft yoke before removing support and lowering the vehicle.

OEM Jeep Wrangler Output Shaft Seal

Output Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Output Shaft Seals found

View related parts
Jeep Wrangler Shaft Seals, Front Passenger Side Part Number: 68396635AA
$96.19 MSRP: $145.00
You Save: $48.81 (34%)
ADD TO CART
Product Specifications
- Other Name: Seal - Axle Drive Shaft; Drive Axle Shaft Seal, Front Right; Axle Seal; Axle Seals; Axle Housing; Seal; Seal Axle Drive Shaft; Seal Oil
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2025 Jeep Wrangler | 80th Anniversary, Freedom, Islander, Rubicon, Rubicon X, Sport, Sport S, Unlimited 80th Anniversary, Unlimited Freedom, Unlimited High Altitude, Unlimited High Altitude 4xe, Unlimited High Tide, Unlimited Islander, Unlimited Moab, Unlimited Rubicon, Unlimited Rubicon 392, Unlimited Rubicon 4xe, Unlimited Rubicon X, Unlimited Rubicon X 4xe, Unlimited Sahara, Unlimited Sahara 4xe, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Sport S 4xe, Unlimited Willys, Unlimited Willys 4xe, Unlimited Willys Sport, Willys, Willys Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.4 L GAS
View related parts
Jeep Wrangler Output Shaft Seal Part Number: 4638904
$26.11 MSRP: $38.35
You Save: $12.24 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal; Automatic Transmission Output Shaft Seal; Transfer Case Output Shaft Seal; Gasket; Axle Seal; Rear Seal; Transfer Case Rear Seal "Npg 16104"; Rear Output Shaft Seal.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-1995 Jeep Wrangler | Base, Islander, Renegade, Rio Grande, S, SE, Sahara | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Output Shaft Seal Part Number: 5013019AA
$29.76 MSRP: $44.30
You Save: $14.54 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Output Shaft; Automatic Transmission Transfer Shaft Seal; Transfer Case Seal; Axle Seal; Seal Output Shaft
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2025, 2005-2006 Jeep Wrangler | 65th Anniversary Edition, 80th Anniversary, Freedom, Islander, Rubicon, Rubicon X, SE, Sport, Sport S, Unlimited, Unlimited 80th Anniversary, Unlimited Freedom, Unlimited High Altitude, Unlimited High Altitude 4xe, Unlimited High Tide, Unlimited Islander, Unlimited Moab, Unlimited Rubicon, Unlimited Rubicon 392, Unlimited Rubicon 4xe, Unlimited Rubicon X, Unlimited Rubicon X 4xe, Unlimited Sahara, Unlimited Sahara 4xe, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Sport S 4xe, Unlimited Willys, Unlimited Willys 4xe, Unlimited Willys Sport, Willys, Willys Sport, X | 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 4.0 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Wrangler Output Shaft Seal Part Number: 5019020AB
$21.57 MSRP: $31.70
You Save: $10.13 (32%)
ADD TO CART
Product Specifications
- Other Name: Seal - Input; Automatic Transmission Transfer Shaft Seal; Transfer Case Seal.; Input Shaft Seal; Rear Extension Seal; Seal Input Gear; Seal Input
- Replaces: 5019020AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2025 Jeep Wrangler | 70th Anniversary, 75th Anniversary, 80th Anniversary, Freedom, Islander, Rubicon, Rubicon X, Sahara, Sport, Sport S, Unlimited 70th Anniversary, Unlimited 75th Anniversary, Unlimited 80th Anniversary, Unlimited Freedom, Unlimited High Altitude, Unlimited High Altitude 4xe, Unlimited High Tide, Unlimited Islander, Unlimited Moab, Unlimited Rubicon, Unlimited Rubicon 392, Unlimited Rubicon 4xe, Unlimited Rubicon X, Unlimited Rubicon X 4xe, Unlimited Sahara, Unlimited Sahara 4xe, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Sport S 4xe, Unlimited Willys, Unlimited Willys 4xe, Unlimited Willys Sport, Unlimited X, Willys, Willys Sport, X, X-S | 2.4L L4, 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4.0L L6, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.8 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Wrangler Shaft Seals, Front Driver Side Part Number: 68398727AA
$53.96 MSRP: $77.20
You Save: $23.24 (31%)
ADD TO CART
Product Specifications
- Other Name: Seal - Axle Drive Shaft; Drive Axle Shaft Seal, Front Left; Axle Seal; Axle Seals; Seal; Seal Axle Drive Shaft
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2025 Jeep Wrangler | 80th Anniversary, Freedom, Islander, Rubicon, Rubicon X, Sport, Sport S, Unlimited 80th Anniversary, Unlimited Freedom, Unlimited High Altitude, Unlimited High Altitude 4xe, Unlimited High Tide, Unlimited Islander, Unlimited Moab, Unlimited Rubicon, Unlimited Rubicon 392, Unlimited Rubicon 4xe, Unlimited Rubicon X, Unlimited Rubicon X 4xe, Unlimited Sahara, Unlimited Sahara 4xe, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Sport S 4xe, Unlimited Willys, Unlimited Willys 4xe, Unlimited Willys Sport, Willys, Willys Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.4 L GAS
View related parts
Jeep Wrangler Output Shaft Seal, Front Part Number: 4762899
$27.13 MSRP: $34.39
You Save: $7.26 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Front Output Oil; Automatic Transmission Output Shaft Seal; Transfer Case Gasket; Multi-Purpose Seal.; Front Seal; Oil Seal, Front Output Shaft Yoke, 1988; Seal, Output, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-1995 Jeep Wrangler | Base, Islander, Renegade, Rio Grande, S, SE, Sahara | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Output Shaft Seal Part Number: 4338893
$37.21 MSRP: $42.15
You Save: $4.94 (12%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Seal - Automatic Transmission Output Shaft Seal; Transfer Case Output Shaft Seal; Transmission Case Seal; Axle Seal.; Front Seal; Seal, Oil, Front Output Shaft Yoke; Oil Seal, Front Output Shaft Yoke; Seal, Oil, Front; Seal Output
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-1995 Jeep Wrangler | Base, Islander, Renegade, Rio Grande, S, SE, Sahara | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Shaft Seals, Front Driver Side Part Number: 68388747AA
$52.26 MSRP: $77.45
You Save: $25.19 (33%)
ADD TO CART
Product Specifications
- Other Name: Seal - Axle Drive Shaft; Drive Axle Shaft Seal, Front Left; Axle Seal; Seal; Seal Axle Drive Shaft
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2025 Jeep Wrangler | 80th Anniversary, Freedom, Islander, Rubicon, Rubicon X, Sport, Sport S, Unlimited 80th Anniversary, Unlimited Freedom, Unlimited High Altitude, Unlimited High Altitude 4xe, Unlimited High Tide, Unlimited Islander, Unlimited Moab, Unlimited Rubicon, Unlimited Rubicon 392, Unlimited Rubicon 4xe, Unlimited Rubicon X, Unlimited Rubicon X 4xe, Unlimited Sahara, Unlimited Sahara 4xe, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Sport S 4xe, Unlimited Willys, Unlimited Willys 4xe, Unlimited Willys Sport, Willys, Willys Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.4 L GAS
View related parts
Jeep Wrangler Output Shaft Seal Part Number: 4798125
$30.97 MSRP: $44.80
You Save: $13.83 (31%)
Product Specifications
- Other Name: Seal - Output Shaft; Automatic Transmission Transfer Shaft Seal; Transfer Case Gasket; Multi-Purpose Seal; Oil Seal; Front Seal; Rear Extension Seal; Seal, Output, Front; Seal Output Shaft; Seal
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2025, 1997-1999 Jeep Wrangler | 70th Anniversary, 75th Anniversary, 80th Anniversary, Freedom, Islander, Rubicon, Rubicon X, SE, Sahara, Sport, Sport S, Unlimited 70th Anniversary, Unlimited 75th Anniversary, Unlimited 80th Anniversary, Unlimited Freedom, Unlimited High Altitude, Unlimited High Altitude 4xe, Unlimited High Tide, Unlimited Islander, Unlimited Moab, Unlimited Rubicon, Unlimited Rubicon 392, Unlimited Rubicon 4xe, Unlimited Rubicon X, Unlimited Rubicon X 4xe, Unlimited Sahara, Unlimited Sahara 4xe, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Sport S 4xe, Unlimited Willys, Unlimited Willys 4xe, Unlimited Willys Sport, Unlimited X, Willys, Willys Sport, X, X-S | 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Wrangler Output Shaft Seal Part Number: 4798117
Product Specifications
- Other Name: Seal - Automatic Transmission Output Shaft Seal; Transfer Case Output Shaft Seal; Axle Seal.; Seal, Oil, W/52098383, 52098384, 52098385; Rear Output Shaft Seal; Transfer Case Seal.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2006 Jeep Wrangler | 65th Anniversary Edition, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Wrangler Output Shaft Seal Part Number: 4798112
Product Specifications
- Other Name: Seal; Automatic Transmission Output Shaft Seal; Transfer Case Seal; Gasket; Axle Seal; Front Seal; Seal, Oil, Front Output Shaft Yoke; Seal Output; Seal Input
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2000 Jeep Wrangler | SE, Sahara, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS

Jeep Wrangler Output Shaft Seal

Choose OEM Output Shaft Seal that meet Jeep factory standards. Jeep designs and tests every component for precision and durability. Each Output Shaft Seal follows strict manufacturing steps to lock in quality and fit. If your Jeep Wrangler matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Wrangler parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Jeep Wrangler Output Shaft Seal Parts and Q&A

Output Shaft Seal
4798117
Q: How to service the front Output Shaft Seal on Jeep Wrangler?
A:
To carry out service on the front output shaft seal, you will first need to raise the vehicle followed by the removal of front propeller shaft. Next, remove the front output shaft yoke. Use a prying tool to separate the seal from the front case. For installation, place a new front output seal on Installer Tool 8143-A so that the garter spring on the seal face into the case. Using a hammer, start to tap the seal into the bore then continue tapping until the installer tool seats against the case.
Output Shaft Seal
5013019AA
Q: How can the rear Output Shaft Seal be removed and installed on Jeep Wrangler?
A:
To remove the rear output shaft seal, first shift the transmission and transfer case into Neutral, then raise and support the vehicle. Mark a line across the pinion shaft and at each end of the propeller shaft for installation reference. Remove the U-joint strap bolts at the pinion shaft yoke and pry open the clamp holding the dust boot to the propeller shaft yoke. Slide the slip yoke off the transmission/transfer case output shaft and remove the propeller shaft. Spread the band clamp holding the output shaft boot to the output shaft slinger or output shaft damper with a suitable awl. Remove the output shaft boot from the slinger or output shaft damper. If the vehicle lacks an output shaft damper, use Puller MD-998056-A to remove the output shaft rear slinger. If equipped with an output shaft damper, use Screws 8421 along with the puller yoke and forcing screw from a bolt-grip puller set to remove the transfer case output shaft damper. Use a suitable pry tool or a slide hammer mounted screw to remove the seal from the rear retainer. For installation, apply a liberal quantity of petroleum jelly to the new rear seal and the output shaft to protect the seal lips during installation. Slide the seal onto Seal Protector 6992 and then onto the output shaft. Use Installer C-4076-B with Handle MD-998323 to drive the seal into the rear bearing retainer. If the vehicle is not equipped with an output shaft damper, install a new output shaft rear slinger with Installer 8408. For vehicles with an output shaft damper, position the damper weight on the output shaft, ensuring it is square to the shaft, then use Installer 8422 to properly position the damper. Install the boot on the output shaft slinger or output shaft damper and crimp the retaining clamp with tool C-4975-A. Slide the slip yoke onto the transmission/transfer case output shaft, align the installation reference marks at the axle yoke, and install the propeller shaft. Tighten the U-joint strap/clamp bolts at the axle yoke to 19 Nm (14 ft. lbs.) and crimp the clamp with Clamp Tool C-4975A to secure the dust boot to the propeller shaft yoke before removing support and lowering the vehicle.