How to Service a Power Steering Hose on 2001 Chrysler Sebring?

First, siphon power steering fluid from the reservoir and then cover all ends of hoses, pump fittings and steering gear ports to stop them from becoming dirty while the repair is done. The Return Hose is made up of the Return Hose With Tube and the Return Hose To Reservoir components. To access the Return Hose With Tube, take off the front fascia, raise the vehicle if you need to and take off the attachment bolt and nut on the forward splash shield. Loosen the pressure hose of the power steering unit from its connection at the gear, then undo the return hose from its place and afterward remove the air shield beneath the left end of the reinforcement. After that, pull the clamp and return hose free from the right end of the return hose tube, along with the tube mounting clips and the tube from the routing clips on the left side of the body. Loop the steering gear end of the return hose tube outside of the frame rail and pull the whole assembly forward, moving it between the ABS ICU and the outline of the rail to remove it from the vehicle. For Return Hose To Reservoir, first suck fluid from the reservoir, then remove the screw holding the reservoir to the engine coolant recovery bottle, raise the reservoir off its guide and separate the hose clamp from the return hose. After removing the front fascia, if necessary, raise the vehicle, then unclamp the right end of the return hose and take the routing clip off the inside of the right frame rail. Adhere to the reverse order of the beginning steps to install the Return Hose With Tube. Pull the hose forward, set it in place in the routing clips and lock it. Join the return hose to the reservoir that's attached to the return hose tube and hold it in place with a clamp. Install the front fascia, lower the car and gradually tighten the left front wheel lug nuts to 135 Nm (100 ft. lbs.) as you crisscross them. Stuff the reservoir with fluid and bleed the system and make sure to look for leaking points. Take the Return Hose To Reservoir and lower it into the routing clip on the right frame rail and secure it to the return hose tube. Retail the front fascia, raise the vehicle up and clip the return hose to the reservoir fitting be sure that the hose clamp is properly set. Drop the reservoir over the chamber, add the screw and fill the container with coolant before releasing any trapped air.

OEM 2001 Chrysler Sebring Power Steering Hose

Power Steering Pressure Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Power Steering Hoses found

View related parts
2001 Chrysler Sebring Power Steering Return Hose Part Number: 4879218AF
$12.20 MSRP: $17.50
You Save: $5.30 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Line - Power Steering Reservoir; Power Steering Hose; Reservoir Hose; Return Hose; Upper Return Hose
- Replaces: 4879218AD, 4879218AE
- Item Weight: 0.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4879218AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
2001 Chrysler Sebring Reservoir Hose Part Number: 4764716AI
$34.19 MSRP: $48.20
You Save: $14.01 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Line - Power Steering Reservoir; Power Steering Reservoir Hose; Power Steering Hose; Power Steering Suction Hose
- Replaces: 4764716AH, 4764716AC, 4764716AG, 4764716AD
- Item Weight: 1.50 Pounds
- Item Dimensions: 18.5 x 15.5 x 6.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4764716AI
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
2001 Chrysler Sebring Power Steering Oil Cooler, Front Lower Part Number: 4879238AG
$33.24 MSRP: $95.35
You Save: $62.11 (66%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cooler - Power Steering; Power Steering Line, Front Lower; Power Steering Cooler; Power Steering Hose; Lower Return Hose
- Position: Front Lower
- Replaces: 4879238AD, 4879238AE, 4879238AC
- Item Weight: 1.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4879238AG
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- Base, GTC, LX, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
2001 Chrysler Sebring Power Steering Pressure Hose Part Number: 4764719AE
$50.50 MSRP: $108.00
You Save: $57.50 (54%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Line - Power Steering Pressure; Power Steering Hose; Pressure Hose
- Replaces: 4764719AC, 4764719AD
- Item Weight: 1.40 Pounds
- Item Dimensions: 40.1 x 27.6 x 13.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4764719AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited | 2.4L L4, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
2001 Chrysler Sebring Power Steering Pressure Hose Part Number: MR272247
$72.48 MSRP: $91.89
You Save: $19.41 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Line - Power Steering Pressure; Pressure Hose; Hose Power Steering Pressure
- Item Weight: 1.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR272247
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2001 Chrysler Sebring Submodels:
- LX, LXi, Limited | 6 Cyl 3.0 L GAS
View related parts
2001 Chrysler Sebring Power Steering Return Hose Part Number: MR333811
Product Specifications
- Other Name: Line - Power Steering Return; Power Steering Hose; Lower Return Hose; Hose Power Steering Return
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR333811
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2001 Chrysler Sebring Submodels:
- LX, LXi, Limited | 6 Cyl 3.0 L GAS
View related parts
2001 Chrysler Sebring Power Steering Return Hose Part Number: MR333810
Product Specifications
- Other Name: Line - Power Steering Return; Lower Return Hose; Hose Power Steering Return
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR333810
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2001 Chrysler Sebring Submodels:
- Base, LX | 4 Cyl 2.4 L GAS
View related parts
2001 Chrysler Sebring Power Steering Return Hose Part Number: MR333806
Product Specifications
- Other Name: Line - Power Steering Return; Center Return Hose; Upper Return Hose; Hose Power Steering Return
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR333806
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2001 Chrysler Sebring Submodels:
- Base, LX, LXi, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
2001 Chrysler Sebring Center Return Hose Part Number: MR297550
Product Specifications
- Other Name: Line - Power Steering Return; Power Steering Return Hose; Upper Return Hose; Hose Power Steering Return
- Item Weight: 0.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR297550
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2001 Chrysler Sebring Submodels:
- Base, LX, LXi, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
2001 Chrysler Sebring Power Steering Pressure Hose Part Number: MR130914
Product Specifications
- Other Name: Line - Power Steering Pressure; Power Steering Hose; Pressure Hose; Hose Power Steering Pressure
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR130914
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2001 Chrysler Sebring Submodels:
- Base, LX | 4 Cyl 2.4 L GAS
View related parts
2001 Chrysler Sebring Reservoir Hose Part Number: 4764419AB
Product Specifications
- Other Name: Line - Power Steering Reservoir; Power Steering Reservoir Hose; Power Steering Hose; Gear Assembly; Power Steering Suction Hose; Hose Power Steering Reservoir
- Item Weight: 1.00 Pounds
- Item Dimensions: 11.7 x 4.6 x 2.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4764419AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
2001 Chrysler Sebring Power Steering Pressure Hose Part Number: 4764446AE
Product Specifications
- Other Name: Line - Power Steering Pressure; Power Steering Hose; Pressure Hose
- Replaces: 4764446AD, 4764446AC
- Item Weight: 1.00 Pounds
- Item Dimensions: 40.7 x 9.5 x 8.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4764446AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 2.7L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS

2001 Chrysler Sebring Power Steering Hose Parts and Q&A

Q: How to Service a Power Steering Hose on 2001 Chrysler Sebring?
A: First, siphon power steering fluid from the reservoir and then cover all ends of hoses, pump fittings and steering gear ports to stop them from becoming dirty while the repair is done. The Return Hose is made up of the Return Hose With Tube and the Return Hose To Reservoir components. To access the Return Hose With Tube, take off the front fascia, raise the vehicle if you need to and take off the attachment bolt and nut on the forward splash shield. Loosen the pressure hose of the power steering unit from its connection at the gear, then undo the return hose from its place and afterward remove the air shield beneath the left end of the reinforcement. After that, pull the clamp and return hose free from the right end of the return hose tube, along with the tube mounting clips and the tube from the routing clips on the left side of the body. Loop the steering gear end of the return hose tube outside of the frame rail and pull the whole assembly forward, moving it between the ABS ICU and the outline of the rail to remove it from the vehicle. For Return Hose To Reservoir, first suck fluid from the reservoir, then remove the screw holding the reservoir to the engine coolant recovery bottle, raise the reservoir off its guide and separate the hose clamp from the return hose. After removing the front fascia, if necessary, raise the vehicle, then unclamp the right end of the return hose and take the routing clip off the inside of the right frame rail. Adhere to the reverse order of the beginning steps to install the Return Hose With Tube. Pull the hose forward, set it in place in the routing clips and lock it. Join the return hose to the reservoir that's attached to the return hose tube and hold it in place with a clamp. Install the front fascia, lower the car and gradually tighten the left front wheel lug nuts to 135 Nm (100 ft. lbs.) as you crisscross them. Stuff the reservoir with fluid and bleed the system and make sure to look for leaking points. Take the Return Hose To Reservoir and lower it into the routing clip on the right frame rail and secure it to the return hose tube. Retail the front fascia, raise the vehicle up and clip the return hose to the reservoir fitting be sure that the hose clamp is properly set. Drop the reservoir over the chamber, add the screw and fill the container with coolant before releasing any trapped air.