How to Effectively Service and Repair a Brake Master Cylinder on 2002 Chrysler Sebring?

The first step to servicing the brake master cylinder is to remove the vehicle wiring harness connector out of the brake fluid level switch inside the master cylinder brake fluid reservoir. Take out the brake tubes from the master cylinder outlets and connect plugs to the open ends on the assembly. Apply Mopers Brake Parts Cleaner or an alternative to the area around the master cylinder at its connection point on the booster. Get rid of the two screws M cost keeping the master cylinder assembly fixed to the vacuum booster and then pull the master cylinder straight from the studs. The studs on the power brake unit should hold the master cylinder assembly in place while the push rod from the power brake vacuum booster matches up with the piston of the master cylinder at installation. Bolt in both mounting nuts and fasten them with a torque of 26 Nm (230 inch lbs.). Join the brake tubes to the connections on the master cylinder and tighten the tube nuts until they reach a torque of 17 Nm (145 inch lbs.) Reconnect the wire connector to the brake fluid level switch, fill the master cylinder with clean Mopers Brake Fluid and keep a safety driver with you for a test drive.

OEM 2002 Chrysler Sebring Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Brake Master Cylinders found

View related parts
2002 Chrysler Sebring Overhaul Kit Part Number: MR493695
Product Specifications
- Other Name: Wheel Cylinder - Brake Master; Cylinder Brake Master
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR493695
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
2002 Chrysler Sebring Overhaul Kit Part Number: MR493691
Product Specifications
- Other Name: Wheel Cylinder - Brake Master; Cylinder Brake Master
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR493691
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
2002 Chrysler Sebring Overhaul Kit Part Number: MR493681
Product Specifications
- Other Name: Wheel Cylinder - Brake Master; Cylinder Brake Master
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR493681
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
2002 Chrysler Sebring Master Cylinder Part Number: MR475973
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Item Weight: 2.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR475973
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
2002 Chrysler Sebring Master Cylinder Part Number: MR475432
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Item Weight: 2.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR475432
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
2002 Chrysler Sebring Master Cylinder Part Number: MR475431
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Item Weight: 2.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: MR475431
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
2002 Chrysler Sebring Master Cylinder Part Number: 5019401AA
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Item Weight: 2.00 Pounds
- Item Dimensions: 5.4 x 3.2 x 8.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5019401AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
2002 Chrysler Sebring Reservoir Tank Part Number: 5019400AA
Product Specifications
- Other Name: Master Cylinder - Brake Master Cylinder; Brake Master Cylinder Reservoir; Reservoir; Reservoir Brake Master Cylinder
- Item Weight: 0.60 Pounds
- Item Dimensions: 9.9 x 6.0 x 4.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5019400AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS

2002 Chrysler Sebring Brake Master Cylinder Parts and Q&A

Q: How to Effectively Service and Repair a Brake Master Cylinder on 2002 Chrysler Sebring?
A: The first step to servicing the brake master cylinder is to remove the vehicle wiring harness connector out of the brake fluid level switch inside the master cylinder brake fluid reservoir. Take out the brake tubes from the master cylinder outlets and connect plugs to the open ends on the assembly. Apply Mopers Brake Parts Cleaner or an alternative to the area around the master cylinder at its connection point on the booster. Get rid of the two screws M cost keeping the master cylinder assembly fixed to the vacuum booster and then pull the master cylinder straight from the studs. The studs on the power brake unit should hold the master cylinder assembly in place while the push rod from the power brake vacuum booster matches up with the piston of the master cylinder at installation. Bolt in both mounting nuts and fasten them with a torque of 26 Nm (230 inch lbs.). Join the brake tubes to the connections on the master cylinder and tighten the tube nuts until they reach a torque of 17 Nm (145 inch lbs.) Reconnect the wire connector to the brake fluid level switch, fill the master cylinder with clean Mopers Brake Fluid and keep a safety driver with you for a test drive.