How to Service and Repair an Engine Mount for Front Mounts on 2002 Dodge Dakota?

Take care of the front engine mount by first taking off the negative battery cable and elevating the hood to make room for the top radiator hose. Always be careful not to lift up the engine through the intake manifold. Attach the engine lifting fixture and put the car up on a hoist. With 2WD, open the insulator's bolt to replace it, raise the engine a bit to get the retaining bolts for the insulator assembly and remove the insulator. When using 4WD, take off the negative battery cable, hoist the vehicle and hook the engine support onto it. Take off the front axle, left mount insulator and starter wires and unbolt the insulator from the frame. Lift the engine slightly and remove the upper insulator to support bracket stud nut and the insulator to support through bolt before you remove the engine mount insulator. Only replace the engine support bracket by removing the bracket-to-transmission bolts and the bolts holding it to the engine block. If you are installing the insulator in a 2WD, raise the engine and place the assembly on the block, then tighten the bolts to 41 Nm (30 ft. lbs.). Reduce the engine speed, slide the insulator assembly into the engine insulator bracket, fix the insulator to bracket thru-bolt and tighten the thru-bolt nut to 68 Nm (50 ft. lbs.). Take out the lifting fixture and link the negative cable to the battery. With the 4WD, set the engine support brackets and tighten both support bracket to block bolt(s) to 41 Nm (30 ft. lbs.) and support bracket to transmission bellhousing bolt(s) to 88 Nm (65 ft. lbs.). Tighten the insulator to the right engine support bracket nut to 41 Nm (30 ft. lbs.) and to the left nut to 102 Nm (75 ft. lbs.). Lower the engine, fit the insulator through the bolt and nut, tighten the nut to 95 Nm (70 ft. lbs.) and after that, mount the starter motor and bolts, securing them to 68 Nm (50 ft. lbs.). Connect the starter wires, take off the engine lifting fixture, set in the front axle assembly, lower the vehicle and at last attach the negative cable to the battery.

OEM 2002 Dodge Dakota Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

21 Engine Mounts found

View related parts
2002 Dodge Dakota Front Mount, Passenger Side Part Number: 52020244AA
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Rear Right, Right; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Rear Insulator; Front Insulator; Insulator Engine Mount
- Position: Passenger Side
- Item Weight: 1.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52020244AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Dodge Dakota Submodels:
- Base, SLT, SLT Plus, Sport, Sport Plus | 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2002 Dodge Dakota Front Mount, Driver Side Part Number: 52022032AB
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Left, Right; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Driver Side
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52022032AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Dodge Dakota Submodels:
- Base, SLT, SLT Plus, SXT, Sport, Sport Plus | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS
View related parts
2002 Dodge Dakota Front Mount, Passenger Side Part Number: 52022008
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Front Right, Right; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Passenger Side
- Item Weight: 7.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52022008
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Dodge Dakota Submodels:
- Base, R/T, SLT, Sport | 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
2002 Dodge Dakota Front Mount, Driver Side Part Number: 52021009
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Front Left, Left; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Front Driver Side
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52021009
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Dodge Dakota Submodels:
- Base, R/T, SLT, Sport | 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
2002 Dodge Dakota Rear Mount Part Number: 52020845AA
Product Specifications
- Other Name: Insulator - Transmission Support; Automatic Transmission Mount; Engine Mount Torque Strut; Bracket; Motor Mount; Rear Insulator; Lower Insulator; Bracket And Insulator Transmission Support; Insulator Engine Mount
- Item Weight: 2.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52020845AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Dodge Dakota Submodels:
- R/T, SLT, Sport | 8 Cyl 5.9 L GAS
View related parts
2002 Dodge Dakota Mount Bracket, Passenger Side Part Number: 52020346AB
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Right; Motor Mount; Bracket Engine Mount; Engine Mount Bracket
- Position: Passenger Side
- Item Weight: 1.70 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52020346AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Dodge Dakota Submodels:
- Base, R/T, SLT, SXT, Sport | 6 Cyl 3.9 L GAS, 8 Cyl 5.9 L GAS
View related parts
2002 Dodge Dakota Front Mount, Driver Side Part Number: 52020345AB
Product Specifications
- Other Name: Bag - Engine Mount; Engine Mount, Left, Rear Left; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Rear Insulator; Front Insulator; Insulator Engine Mount
- Position: Driver Side
- Item Weight: 8.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52020345AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Dodge Dakota Submodels:
- SLT, Sport | 8 Cyl 5.9 L GAS
View related parts
2002 Dodge Dakota Front Mount, Passenger Side Part Number: 52020342AA
Product Specifications
- Other Name: Insulator Engine Mount; Engine Mount, Right; Engine Mount Bracket; Motor Mount; Front Insulator
- Position: Passenger Side
- Item Weight: 4.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52020342AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Dodge Dakota Submodels:
- R/T, SLT, Sport | 8 Cyl 5.9 L GAS
View related parts
2002 Dodge Dakota Mount Bracket, Driver Side Part Number: 52020257AB
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Left; Motor Mount; Bracket Engine Mount; Engine Mount Bracket
- Position: Driver Side
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52020257AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Dodge Dakota Submodels:
- Base, SLT, SLT Plus, Sport, Sport Plus | 8 Cyl 4.7 L GAS
View related parts
2002 Dodge Dakota Mount Bracket, Driver Side Part Number: 52020247AC
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Left; Motor Mount; Front Mount; Bracket Engine Mount; Engine Mount Bracket
- Position: Driver Side
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52020247AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Dodge Dakota Submodels:
- Base, R/T, SLT, SXT, Sport | 6 Cyl 3.9 L GAS, 8 Cyl 5.9 L GAS
View related parts
2002 Dodge Dakota Front Mount, Rear Driver Side Part Number: 52020243AB
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Left, Rear Left; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Rear Insulator; Front Insulator; Insulator Engine Mount
- Position: Rear Driver Side
- Item Weight: 8.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52020243AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Dodge Dakota Submodels:
- Base, R/T, SLT, SLT Plus, Sport, Sport Plus | 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2002 Dodge Dakota Rear Mount Part Number: 52019998
Product Specifications
- Other Name: Insulator - Transmission Support; Automatic Transmission Mount; Engine Mount Torque Strut; Bracket; Motor Mount; Rear Insulator; Lower Insulator; Insulator; Bracket And Insulator Transmission Support; Isolator Engine Mount
- Item Weight: 2.80 Pounds
- Item Dimensions: 7.6 x 4.0 x 3.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52019998
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Dodge Dakota Submodels:
- Base, R/T, SLT, SLT Plus, SXT, Sport, Sport Plus, WS | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
2002 Dodge Dakota Front Mount, Driver Side Part Number: 52019961AC
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Front Left, Left; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Front Driver Side
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52019961AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Dodge Dakota Submodels:
- Base, SLT, SLT Plus, Sport, Sport Plus | 8 Cyl 4.7 L GAS
View related parts
2002 Dodge Dakota Mount Bracket, Passenger Side Part Number: 52019958AC
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Right; Motor Mount; Bracket Engine Mount; Engine Mount Bracket
- Position: Passenger Side
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52019958AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Dodge Dakota Submodels:
- Base, SLT, SLT Plus, Sport, Sport Plus | 8 Cyl 4.7 L GAS
View related parts
2002 Dodge Dakota Rear Mount Part Number: 52019394AD
Product Specifications
- Other Name: Insulator - Transmission Support; Automatic Transmission Mount; Engine Mount Torque Strut; Bracket; Motor Mount; Rear Insulator; Lower Insulator; Bracket And Insulator Transmission Support; Insulator Engine Mount
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52019394AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Dodge Dakota Submodels:
- Base, R/T, SLT, SLT Plus, Sport, Sport Plus | 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2002 Dodge Dakota Front Mount, Driver Side Part Number: 52010017
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Left; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Driver Side
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52010017
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2002 Dodge Dakota Submodels:
- Base, SLT, SXT, Sport | 6 Cyl 3.9 L GAS
View related parts
2002 Dodge Dakota Front Mount, Passenger Side Part Number: 52009030
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Right; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Passenger Side
- Item Weight: 5.70 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52009030
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Dodge Dakota Submodels:
- Base, SLT, SXT, Sport | 6 Cyl 3.9 L GAS
View related parts
2002 Dodge Dakota Front Mount, Passenger Side Part Number: 52019962AC
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Front Right, Right; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Front Passenger Side
- Item Weight: 4.80 Pounds
- Item Dimensions: 9.4 x 5.1 x 4.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52019962AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Dodge Dakota Submodels:
- Base, SLT, SLT Plus, Sport, Sport Plus | 8 Cyl 4.7 L GAS
View related parts
2002 Dodge Dakota Front Mount, Driver Side Part Number: 52022031AC
Product Specifications
- Other Name: Insulator - Engine Mount; Engine Mount, Left, Right; Engine Mount Bracket; Motor Mount; Front Insulator; Insulator Engine Mount
- Position: Driver Side
- Item Weight: 7.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52022031AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Dodge Dakota Submodels:
- Base, SLT, SLT Plus, SXT, Sport, Sport Plus | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS
View related parts
2002 Dodge Dakota Rear Mount Part Number: 52019615AC
Product Specifications
- Other Name: Insulator - Engine Mount; Support Bracket; Isolator, Rear; Torque Strut; Bracket; Motor Mount; Rear Insulator; Insulator Engine Mount
- Position: Rear
- Item Weight: 1.60 Pounds
- Item Dimensions: 6.0 x 4.1 x 3.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52019615AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2002 Dodge Dakota Submodels:
- Base, SLT, SLT Plus, SXT, Sport, Sport Plus | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS

| Page 1 of 2 |Next >

1-20 of 21 Results

2002 Dodge Dakota Engine Mount Parts and Q&A

Q: How to Service and Repair an Engine Mount for Front Mounts on 2002 Dodge Dakota?
A: Take care of the front engine mount by first taking off the negative battery cable and elevating the hood to make room for the top radiator hose. Always be careful not to lift up the engine through the intake manifold. Attach the engine lifting fixture and put the car up on a hoist. With 2WD, open the insulator's bolt to replace it, raise the engine a bit to get the retaining bolts for the insulator assembly and remove the insulator. When using 4WD, take off the negative battery cable, hoist the vehicle and hook the engine support onto it. Take off the front axle, left mount insulator and starter wires and unbolt the insulator from the frame. Lift the engine slightly and remove the upper insulator to support bracket stud nut and the insulator to support through bolt before you remove the engine mount insulator. Only replace the engine support bracket by removing the bracket-to-transmission bolts and the bolts holding it to the engine block. If you are installing the insulator in a 2WD, raise the engine and place the assembly on the block, then tighten the bolts to 41 Nm (30 ft. lbs.). Reduce the engine speed, slide the insulator assembly into the engine insulator bracket, fix the insulator to bracket thru-bolt and tighten the thru-bolt nut to 68 Nm (50 ft. lbs.). Take out the lifting fixture and link the negative cable to the battery. With the 4WD, set the engine support brackets and tighten both support bracket to block bolt(s) to 41 Nm (30 ft. lbs.) and support bracket to transmission bellhousing bolt(s) to 88 Nm (65 ft. lbs.). Tighten the insulator to the right engine support bracket nut to 41 Nm (30 ft. lbs.) and to the left nut to 102 Nm (75 ft. lbs.). Lower the engine, fit the insulator through the bolt and nut, tighten the nut to 95 Nm (70 ft. lbs.) and after that, mount the starter motor and bolts, securing them to 68 Nm (50 ft. lbs.). Connect the starter wires, take off the engine lifting fixture, set in the front axle assembly, lower the vehicle and at last attach the negative cable to the battery.