How to Safely Service an Air Bag Control Module on 2007 Dodge Ram 2500?

To take care of the Air Bag Control Module, first turn off the supplemental restraint system by removing the battery negative cable, isolating it and waiting two minutes so the system capacitor discharges. Keep the occupant restraint controller in good condition so drops or strikes do not damage the impact sensor, as this calls for the entire module to be replaced. Align the Occupant Restraint Controller over the three studs of the mounting bracket on the floor panel transmission tunnel such that the pin on the right mounting flange connects with the bracket. After locating the arrow on the ORC label toward the front of the engine, fit the three nuts and tighten them at a torque of 10 Nm (7 ft. lbs.). Attach the ORC connector ends to the wiring receptacles and make certain the latches are properly snapped together. Reinstall the ORC cover once you are finished, though wait until the supplemental restraint system verification has taken place after working on any pillar component.

OEM 2007 Dodge Ram 2500 Air Bag Control Module

SRS Airbag Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Air Bag Control Modules found

View related parts
2007 Dodge Ram 2500 Side Impact Sensor Part Number: 56043167AB
Product Specifications
- Other Name: Sensor - Impact; Air Bag Impact Sensor; Air Bag Sensor; Diagnostic Module; Side Sensor
- Replaces: 56043167AA
- Item Weight: 0.50 Pounds
- Item Dimensions: 3.8 x 2.6 x 1.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 56043167AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Ram 2500 Submodels:
- Laramie, Power Wagon, SLT, ST, SXT, Sport, TRX4 | 5.7L V8, 5.9L L6, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS
View related parts
2007 Dodge Ram 2500 Diagnostic Module Part Number: 56043706AF
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Passenger Presence Module; Occupant Module
- Replaces: 56043706AD, 56043706AC, 56043706AE
- Item Weight: 1.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 56043706AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Ram 2500 Submodels:
- Laramie, Power Wagon, SLT, ST, Sport, TRX4 | 5.7L V8, 5.9L L6, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS
View related parts
2007 Dodge Ram 2500 Diagnostic Module Part Number: 56043708AF
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Passenger Presence Module; Occupant Module
- Replaces: 56043708AE, 56043708AC, 56043708AD
- Item Weight: 1.30 Pounds
- Item Dimensions: 7.2 x 6.1 x 3.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 56043708AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Dodge Ram 2500 Submodels:
- Laramie, Power Wagon, SLT, ST, Sport, TRX4 | 5.7L V8, 5.9L L6, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS

2007 Dodge Ram 2500 Air Bag Control Module Parts and Q&A

Q: How to Safely Service an Air Bag Control Module on 2007 Dodge Ram 2500?
A: To take care of the Air Bag Control Module, first turn off the supplemental restraint system by removing the battery negative cable, isolating it and waiting two minutes so the system capacitor discharges. Keep the occupant restraint controller in good condition so drops or strikes do not damage the impact sensor, as this calls for the entire module to be replaced. Align the Occupant Restraint Controller over the three studs of the mounting bracket on the floor panel transmission tunnel such that the pin on the right mounting flange connects with the bracket. After locating the arrow on the ORC label toward the front of the engine, fit the three nuts and tighten them at a torque of 10 Nm (7 ft. lbs.). Attach the ORC connector ends to the wiring receptacles and make certain the latches are properly snapped together. Reinstall the ORC cover once you are finished, though wait until the supplemental restraint system verification has taken place after working on any pillar component.