How to Service and Repair a Steering Knuckle on 2007 Jeep Wrangler?

It is important to start the process by raising and holding up the car, then removing the wheel before addressing the steering knuckle. After that, take out the external tie rod end nut and separate the tie rod from the knuckle with the special 9360 tool. Use the special tool to remove the nut on the right side and then separate that drag link from the knuckle. After securing the area, loosen the disc brake caliper bolts to put no pressure on the brake hose and then remove the disc brake rotor. If you have the tools, remove the nut holding the axle shaft, along with the bolt on the wheel speed sensor and pull the wheel speed sensor out through the brake shield's hole. After that, take out the lower ball joint cotter pin and nut and follow the same step for the upper ball joint. To separate the lower ball joint from the knuckle, use C-4150A puller and to separate the upper, use 9360 separator. Last, take out the steering knuckle and carry the hub/bearing with its brake shield, if required.

OEM 2007 Jeep Wrangler Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Steering Knuckles found

View related parts
2007 Jeep Wrangler Knuckle, Front Passenger Side Part Number: 68003652AB
$48.32 MSRP: $82.95
You Save: $34.63 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle - Sunrider Top Pivot; Convertible Top Hinge, Front Right; Knuckle Sunrider Top Pivot
- Position: Front Passenger Side
- Replaces: 68003652AA
- Item Weight: 0.70 Pounds
- Item Dimensions: 8.3 x 2.1 x 1.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68003652AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Jeep Wrangler Submodels:
- Unlimited 70th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited X | 3.8L V6, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
2007 Jeep Wrangler Knuckle, Front Driver Side Part Number: 68003653AB
$49.83 MSRP: $85.55
You Save: $35.72 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle - Sunrider Top Pivot; Convertible Top Hinge, Front Left; Knuckle Sunrider Top Pivot
- Position: Front Driver Side
- Replaces: 68003653AA
- Item Weight: 11.00 Pounds
- Item Dimensions: 20.4 x 12.2 x 10.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68003653AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Jeep Wrangler Submodels:
- Unlimited 70th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited X | 3.8L V6, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
2007 Jeep Wrangler Knuckle, Front Driver Side Part Number: 68004087AA
$449.74 MSRP: $684.00
You Save: $234.26 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle - Front; Steering Knuckle, Front Left; Knuckle Front
- Position: Front Driver Side
- Item Weight: 11.80 Pounds
- Item Dimensions: 4.7 x 8.0 x 10.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68004087AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Jeep Wrangler Submodels:
- 70th Anniversary, 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 70th Anniversary, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S, Unlimited X, X, X-S | 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
2007 Jeep Wrangler Knuckle, Front Passenger Side Part Number: 68017195AA
$569.08 MSRP: $865.00
You Save: $295.92 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle - Front; Steering Knuckle, Front Right; Knuckle Front
- Position: Front Passenger Side
- Item Weight: 11.80 Pounds
- Item Dimensions: 10.0 x 9.8 x 4.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68017195AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Jeep Wrangler Submodels:
- 70th Anniversary, 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 70th Anniversary, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S, Unlimited X, X | 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
2007 Jeep Wrangler Knuckle, Front Passenger Side Part Number: 68004086AA
$501.67 MSRP: $762.00
You Save: $260.33 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle - Front; Steering Knuckle, Front Right; Knuckle Front
- Position: Front Passenger Side
- Item Weight: 14.80 Pounds
- Item Dimensions: 5.0 x 10.1 x 11.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68004086AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Jeep Wrangler Submodels:
- 70th Anniversary, 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 70th Anniversary, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S, Unlimited X, X, X-S | 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS

2007 Jeep Wrangler Steering Knuckle Parts and Q&A

Q: How to Service and Repair a Steering Knuckle on 2007 Jeep Wrangler?
A: It is important to start the process by raising and holding up the car, then removing the wheel before addressing the steering knuckle. After that, take out the external tie rod end nut and separate the tie rod from the knuckle with the special 9360 tool. Use the special tool to remove the nut on the right side and then separate that drag link from the knuckle. After securing the area, loosen the disc brake caliper bolts to put no pressure on the brake hose and then remove the disc brake rotor. If you have the tools, remove the nut holding the axle shaft, along with the bolt on the wheel speed sensor and pull the wheel speed sensor out through the brake shield's hole. After that, take out the lower ball joint cotter pin and nut and follow the same step for the upper ball joint. To separate the lower ball joint from the knuckle, use C-4150A puller and to separate the upper, use 9360 separator. Last, take out the steering knuckle and carry the hub/bearing with its brake shield, if required.