How to Service a Brake Light Switch on 2008 Dodge Durango?

First, turn off the Supplemental Restraint System (SRS) by taking out the car's battery negative cable and holding it isolated for two minutes, so the capacitor can empty itself. After that, find the brake lamp switch next to where the support bracket connects to the lower steering column. Separate the wire harness connector from the brake lamp switch and then twist the switch housing clockwise approximately 30 degrees until the keys on the locking collar fall into the keyed hole in the switch mounting bracket. Use the switch and pull it right back out of the keyed hole to take it off the bracket. A self-adjusting switch plunger cannot be used again after being removed from the housing, so a replacement is necessary if needed. Get rid of the removed brake lamp switch.

OEM 2008 Dodge Durango Brake Light Switch

Brake Lamp Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Brake Light Switches found

View related parts
2008 Dodge Durango Parking Brake Switch, Black Part Number: 4221463
$18.50 MSRP: $27.20
You Save: $8.70 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Parking Brake; Electronic Parking Brake Control Switch; Parking Brake Warning Switch; Seat Adjuster, W/Bezel, Black Buttons, Woodgrain, W/Memory Opening.
- Item Weight: 0.40 Pounds
- Item Dimensions: 1.5 x 1.6 x 2.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4221463
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2008 Dodge Durango Submodels:
- Adventurer, Base, Citadel, Crew, Express, GT, GT Plus, GT Premium, Heat, Limited, Limited Hybrid, Pursuit, R/T, R/T Hemi Orange, R/T Plus, R/T Premium, Rallye, SE, SLT, SLT Plus, SRT, SRT 392, SRT 392 Plus, SRT 392 Premium, SRT Hellcat, SRT Hellcat Plus, SRT Hellcat Premium, ST, SXT, SXT Plus, Special Service, Sport | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
2008 Dodge Durango Switch Package - Stop Lamp Part Number: 5083344AB
Product Specifications
- Other Name: SW PKG-STOP LAMP
- SKU: 5083344AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2008 Dodge Durango Submodels:
- Adventurer, Base, Limited, Limited Hybrid, R/T, SE, SLT, SLT Plus, ST, SXT, Sport | 3.7L V6, 4.7L V8, 5.7L V8, 5.9L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS

2008 Dodge Durango Brake Light Switch Parts and Q&A

Q: How to Service a Brake Light Switch on 2008 Dodge Durango?
A: First, turn off the Supplemental Restraint System (SRS) by taking out the car's battery negative cable and holding it isolated for two minutes, so the capacitor can empty itself. After that, find the brake lamp switch next to where the support bracket connects to the lower steering column. Separate the wire harness connector from the brake lamp switch and then twist the switch housing clockwise approximately 30 degrees until the keys on the locking collar fall into the keyed hole in the switch mounting bracket. Use the switch and pull it right back out of the keyed hole to take it off the bracket. A self-adjusting switch plunger cannot be used again after being removed from the housing, so a replacement is necessary if needed. Get rid of the removed brake lamp switch.