Other Name: Seat Belt - Buckle Half; Seat Belt Receptacle, Front Center, Rear Left; Rear Belt Assembly Buckle; Latch; Seat Belt Buckle Half Center Buckle; Seat Belt Buckle Half Center Seat
Position: Front Center
Replaces: 5GW281D5AA
Item Weight: 1.00 Pounds
Item Dimensions: 12.2 x 3.1 x 1.7 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 5GW281D5AC
Warranty: This genuine part is guaranteed by Mopar's
factory warranty.
More Info
Fits the following 2008 Dodge Ram 1500 Submodels:
Laramie, SLT, SRT-10, ST, SXT, Sport, TRX4 | 10 Cyl 8.3 L GAS, 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
Other Name: Seat Belt - Front Inner; Seat Belt Receptacle, Rear Right; Rear Belt Assembly Buckle; Latch; Front Inner Center Shoulder Belt Buckle; Front Center Seat.
Position: Inner Passenger Side
Replaces: 5HG321D5AD, 5HG321J3AD
Item Weight: 1.20 Pounds
Item Dimensions: 9.4 x 3.4 x 2.9 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 5HG321X9AD
Warranty: This genuine part is guaranteed by Mopar's
factory warranty.
More Info
Fits the following 2008 Dodge Ram 1500 Submodels:
Laramie, SLT, SRT-10, ST, SXT, Sport, TRX4 | 10 Cyl 8.3 L GAS, 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
Other Name: Seat Belt - Rear Inner; Seat Belt Receptacle, Rear; Latch; Seat Belt Rear Inner Right Seat; Seat Belt Rear Inner
Position: Rear Inner
Item Weight: 1.00 Pounds
Item Dimensions: 15.1 x 2.6 x 2.1 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 5KN381J3AA
Warranty: This genuine part is guaranteed by Mopar's
factory warranty.
More Info
Fits the following 2008 Dodge Ram 1500 Submodels:
Laramie, SLT, SRT-10, ST, SXT, Sport, TRX4 | 10 Cyl 8.3 L GAS, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
| Page 1 of 2 |Next >
1-20 of 40 Results
2008 Dodge Ram 1500 Seat Belt Parts and Q&A
Q: How to Maintain and Fix the Rear Center Seat Belt in a Quad Cab on 2008 Dodge Ram 1500?
A: To handle rear center seat belt service and repairs in a Quad Cab, check every seat belt, buckle, hardware, retractor, strap and anchor for proper mounting, correct operation or wear, replace broken, worn or frayed belts, straighten twisted belts and fix or change any worn, damaged buckles, retractors, plates or anchors with parts from the DaimlerChrysler Mopar Parts Catalog. Only one unit contains the right outboard occupant seat belt buckle, the rear center seat belt and its retractor. Mount the rear center seat belt retractor and the right outboard occupant buckle unit under the rear floor near the base of the cab back panel. Then screw the right side seat belt retractor bracket to the body bracket on the upper cab back panel reinforcement. Screw in the two hold-down screws to 20 Nm (15 ft. lbs.); pull up the rear center seat belt webbing; and carefully stretch the cover over the belt bracket on the top part of the cab panel until it's seated. Coat the center rear belt's pass-thru with webbing, leverage the bezel upward to fit over the fabric and bracket and press the snap features against the bracket until secure. On vehicles that have a 60/40 split, only the 60 percent part of the rear bench should be reinstalled. Bring the middle seat belt lower anchor forward and put it between the rear seat back and seat cushion, then clamp it to the left side of the seat belt retractor mounting bracket on the lower panel of the back seat using a screw that you tighten up to 40 Nm (29 ft. lbs.). Application of 40 Nm (29 ft. lbs.) of torque to the right screw holding the seat belt retractor in place and adjusting the rear seat cushion to its former position finish this operation.